27/02/2023,10:28:27,$HST:Application just created
27/02/2023,10:28:27,$HST:SW-version 1.24, e-Callisto
27/02/2023,10:28:27,$HST:Configurationfile read
27/02/2023,10:28:27,$HST:Switched to automatic
27/02/2023,10:28:27,$HST:ATmega16 pre-configured
27/02/2023,10:28:27,$HST:Frequencyfile frq00470.cfg
27/02/2023,10:28:27,$HST:Callisto ready now...
27/02/2023,10:28:27,$HST:Measurement idle
27/02/2023,10:28:28,$HST:File scheduler.cfg read
27/02/2023,10:28:28,$HST:Measurement enable
27/02/2023,10:28:28,$CRX:AGC gain = 2.13V
27/02/2023,10:28:28,$CRX:Emitter BF199 = 0.19V
27/02/2023,10:28:28,$CRX:Analog Input = 11.32
27/02/2023,10:28:33,$HST:File FRQ00470.CFG read
27/02/2023,10:28:33,$HST:No calibration file found
27/02/2023,10:28:33,$HST:Plot buffer erased...
27/02/2023,10:28:33,$HST:Parametrisation RCU
27/02/2023,10:28:33,$CRX:V1.8 / 2012-04-02
27/02/2023,10:28:33,$HST:Found LO=25.43 MHz
27/02/2023,10:28:33,$CRX:Debug=Off
27/02/2023,10:28:33,$CRX:Trigger=No
27/02/2023,10:28:33,$CRX:FPUcodex=0
27/02/2023,10:28:33,$CRX:GS =0
27/02/2023,10:28:33,$CRX:GA =0
27/02/2023,10:28:33,$CRX:Delay=0msec
27/02/2023,10:28:33,$CRX:Frequency=0.0MHz
27/02/2023,10:28:33,$HST:Receiver connected
27/02/2023,10:28:33,$CRX:Sweeplength=0
27/02/2023,10:28:33,$CRX:low_band_max=171MHz
27/02/2023,10:28:33,$CRX:mid_band_max=450MHz
27/02/2023,10:28:33,$CRX:high_band_max=863MHz
27/02/2023,10:28:33,$CRX:Idle=0
27/02/2023,10:28:33,$CRX:V1.8 / 2012-04-02
27/02/2023,10:28:33,$HST:Found LO=25.43 MHz
27/02/2023,10:28:33,$CRX:Debug=Off
27/02/2023,10:28:33,$CRX:Trigger=Extern
27/02/2023,10:28:33,$CRX:FPUcodex=0
27/02/2023,10:28:33,$CRX:GS =0
27/02/2023,10:28:33,$CRX:GA =624
27/02/2023,10:28:33,$CRX:Delay=0msec
27/02/2023,10:28:33,$CRX:Frequency=45.0MHz
27/02/2023,10:28:33,$HST:Receiver connected
27/02/2023,10:28:33,$CRX:Sweeplength=200
27/02/2023,10:28:33,$CRX:low_band_max=171MHz
27/02/2023,10:28:33,$CRX:mid_band_max=450MHz
27/02/2023,10:28:33,$CRX:high_band_max=863MHz
27/02/2023,10:28:33,$CRX:Idle=0
27/02/2023,10:28:39,$HST:File FRQ00470.CFG read
27/02/2023,10:28:39,$HST:No calibration file found
27/02/2023,10:28:39,$HST:Plot buffer erased...
27/02/2023,10:28:39,$HST:Parametrisation RCU
27/02/2023,10:28:39,$CRX:V1.8 / 2012-04-02
27/02/2023,10:28:39,$HST:Found LO=25.43 MHz
27/02/2023,10:28:39,$CRX:Debug=Off
27/02/2023,10:28:39,$CRX:Trigger=Extern
27/02/2023,10:28:39,$CRX:FPUcodex=0
27/02/2023,10:28:39,$CRX:GS =0
27/02/2023,10:28:39,$CRX:GA =624
27/02/2023,10:28:39,$CRX:Delay=0msec
27/02/2023,10:28:39,$CRX:Frequency=45.0MHz
27/02/2023,10:28:39,$HST:Receiver connected
27/02/2023,10:28:39,$CRX:Sweeplength=200
27/02/2023,10:28:39,$CRX:low_band_max=171MHz
27/02/2023,10:28:39,$CRX:mid_band_max=450MHz
27/02/2023,10:28:39,$CRX:high_band_max=863MHz
27/02/2023,10:28:39,$CRX:Idle=0
27/02/2023,10:28:39,$CRX:V1.8 / 2012-04-02
27/02/2023,10:28:39,$HST:Found LO=25.43 MHz
27/02/2023,10:28:39,$CRX:Debug=Off
27/02/2023,10:28:39,$CRX:Trigger=Extern
27/02/2023,10:28:39,$CRX:FPUcodex=0
27/02/2023,10:28:39,$CRX:GS =0
27/02/2023,10:28:39,$CRX:GA =624
27/02/2023,10:28:39,$CRX:Delay=0msec
27/02/2023,10:28:39,$CRX:Frequency=45.0MHz
27/02/2023,10:28:39,$HST:Receiver connected
27/02/2023,10:28:39,$CRX:Sweeplength=200
27/02/2023,10:28:39,$CRX:low_band_max=171MHz
27/02/2023,10:28:39,$CRX:mid_band_max=450MHz
27/02/2023,10:28:39,$CRX:high_band_max=863MHz
27/02/2023,10:28:39,$CRX:Idle=0
27/02/2023,10:29:07,$HST:Param. RCU due to START
27/02/2023,10:29:07,$HST:Actual focuscode 01
27/02/2023,10:29:07,$HST:Enable data transfer
27/02/2023,10:29:07,$HST:Continuous measurement
27/02/2023,10:29:07,$CRX:Started
27/02/2023,10:29:08,$HST:Start new FITS-file
27/02/2023,10:29:08,$HST:Continous measurement
27/02/2023,10:31:05,$HST:XYZ plot selected
27/02/2023,11:59:58,$HST:Measurement stop
27/02/2023,11:59:58,$HST:EOT (&) detected
27/02/2023,11:59:58,$HST:Measurement wait...
27/02/2023,11:59:58,$HST:Measurement halted
27/02/2023,11:59:58,$HST:Measurement stop
27/02/2023,11:59:58,$CRX:Stopped
27/02/2023,11:59:58,$HST:Measurement wait...
27/02/2023,11:59:59,$HST:Measurement halted
27/02/2023,11:59:59,$HST:Measurement idle
27/02/2023,11:59:59,$CRX:Stopped
27/02/2023,11:59:59,$HST:Measurement enable
27/02/2023,11:59:59,$CRX:AGC gain = 2.39V
27/02/2023,11:59:59,$CRX:Emitter BF199 = 0.20V
27/02/2023,11:59:59,$CRX:Analog Input = 11.32
27/02/2023,12:00:00,$HST:Autostart via scheduler
27/02/2023,12:00:00,$HST:Param. RCU due to START
27/02/2023,12:00:00,$HST:Actual focuscode 02
27/02/2023,12:00:00,$HST:Enable data transfer
27/02/2023,12:00:00,$HST:Continuous measurement
27/02/2023,12:00:00,$CRX:Started
27/02/2023,12:00:00,$HST:Start new FITS-file
27/02/2023,12:00:00,$HST:Continous measurement
27/02/2023,15:59:58,$HST:Measurement stop
27/02/2023,15:59:58,$HST:Measurement wait...
27/02/2023,15:59:58,$HST:EOT (&) detected
27/02/2023,15:59:58,$HST:Measurement halted
27/02/2023,15:59:58,$HST:Measurement stop
27/02/2023,15:59:58,$CRX:Stopped
27/02/2023,15:59:58,$HST:Measurement wait...
27/02/2023,15:59:59,$HST:Measurement halted
27/02/2023,15:59:59,$HST:Measurement idle
27/02/2023,15:59:59,$CRX:Stopped
27/02/2023,16:00:00,$HST:Measurement enable
27/02/2023,16:00:00,$CRX:AGC gain = 2.40V
27/02/2023,16:00:00,$CRX:Emitter BF199 = 0.20V
27/02/2023,16:00:00,$CRX:Analog Input = 11.32
27/02/2023,16:00:00,$HST:Autostart via scheduler
27/02/2023,16:00:00,$HST:Param. RCU due to START
27/02/2023,16:00:00,$HST:Actual focuscode 02
27/02/2023,16:00:00,$HST:Enable data transfer
27/02/2023,16:00:00,$HST:Continuous measurement
27/02/2023,16:00:00,$CRX:Started
27/02/2023,16:00:00,$HST:Start new FITS-file
27/02/2023,16:00:00,$HST:Continous measurement
27/02/2023,19:59:58,$HST:Measurement stop
27/02/2023,19:59:58,$HST:Measurement wait...
27/02/2023,19:59:58,$HST:EOT (&) detected
27/02/2023,19:59:58,$HST:Measurement halted
27/02/2023,19:59:58,$HST:Measurement stop
27/02/2023,19:59:58,$CRX:Stopped
27/02/2023,19:59:58,$HST:Measurement wait...
27/02/2023,19:59:59,$HST:Measurement halted
27/02/2023,19:59:59,$HST:Measurement idle
27/02/2023,19:59:59,$CRX:Stopped
27/02/2023,20:00:00,$HST:Measurement enable
27/02/2023,20:00:00,$CRX:AGC gain = 2.59V
27/02/2023,20:00:00,$CRX:Emitter BF199 = 0.20V
27/02/2023,20:00:00,$CRX:Analog Input = 11.32
27/02/2023,20:00:00,$HST:Autostart via scheduler
27/02/2023,20:00:00,$HST:Param. RCU due to START
27/02/2023,20:00:00,$HST:Actual focuscode 02
27/02/2023,20:00:00,$HST:Enable data transfer
27/02/2023,20:00:00,$HST:Continuous measurement
27/02/2023,20:00:00,$CRX:Started
27/02/2023,20:00:00,$HST:Start new FITS-file
27/02/2023,20:00:00,$HST:Continous measurement
27/02/2023,20:00:01,$HST:No more entries in scheduler.
28/02/2023,00:00:00,$HST:Midnight -> memo cleared
28/02/2023,00:00:00,$HST:EOF(logfile)