18.08.2021,14:35:13,$HST:Application just created
18.08.2021,14:35:13,$HST:SW-version 1.24, e-Callisto
18.08.2021,14:35:13,$HST:Configurationfile read
18.08.2021,14:35:13,$HST:Switched to automatic
18.08.2021,14:35:13,$HST:ATmega16 pre-configured
18.08.2021,14:35:13,$HST:Frequencyfile frq00470.cfg
18.08.2021,14:35:13,$HST:Callisto ready now...
18.08.2021,14:35:14,$HST:Measurement idle
18.08.2021,14:35:14,$HST:File scheduler.cfg read
18.08.2021,14:35:14,$HST:Measurement enable
18.08.2021,14:35:14,$CRX:AGC gain = 2.54V
18.08.2021,14:35:20,$HST:File FRQ00470.CFG read
18.08.2021,14:35:20,$HST:No calibration file found
18.08.2021,14:35:20,$HST:Plot buffer erased...
18.08.2021,14:35:20,$HST:Parametrisation RCU
18.08.2021,14:35:27,$HST:File FRQ00470.CFG read
18.08.2021,14:35:27,$HST:No calibration file found
18.08.2021,14:35:27,$HST:Plot buffer erased...
18.08.2021,14:35:27,$HST:Parametrisation RCU
18.08.2021,14:35:30,$HST:XY plot selected
18.08.2021,14:35:37,$HST:Param. RCU due to START
18.08.2021,14:35:37,$HST:Actual focuscode 01
18.08.2021,14:35:38,$HST:Enable data transfer
18.08.2021,14:35:38,$HST:Continuous measurement
18.08.2021,14:35:38,$HST:Start new FITS-file
18.08.2021,14:35:38,$HST:Continous measurement
18.08.2021,14:37:32,$CRX:e-Callisto ETH Zurich
18.08.2021,14:37:32,$HST:Watchdog triggered -> Reset
18.08.2021,14:37:32,$CRX:V1.8 / 2012-04-02
18.08.2021,14:37:32,$HST:Found LO=25.43 MHz
18.08.2021,14:37:33,$CRX:V1.8 / 2012-04-02
18.08.2021,14:37:33,$HST:Found LO=25.43 MHz
18.08.2021,14:37:33,$CRX:Debug=Off
18.08.2021,14:37:33,$CRX:Trigger=No
18.08.2021,14:37:33,$CRX:FPUcodex=0
18.08.2021,14:37:33,$CRX:GS =0
18.08.2021,14:37:33,$CRX:GA =0
18.08.2021,14:37:33,$CRX:Delay=0msec
18.08.2021,14:37:33,$CRX:Frequency=0.0MHz
18.08.2021,14:37:33,$HST:Receiver connected
18.08.2021,14:37:33,$CRX:Sweeplength=0
18.08.2021,14:37:33,$CRX:low_band_max=171MHz
18.08.2021,14:37:33,$CRX:mid_band_max=450MHz
18.08.2021,14:37:33,$CRX:high_band_max=863MHz
18.08.2021,14:37:33,$CRX:Idle=0
18.08.2021,14:37:33,$CRX:V1.8 / 2012-04-02
18.08.2021,14:37:33,$HST:Found LO=25.43 MHz
18.08.2021,14:37:33,$CRX:Debug=Off
18.08.2021,14:37:33,$CRX:Trigger=Extern
18.08.2021,14:37:33,$CRX:FPUcodex=0
18.08.2021,14:37:33,$CRX:GS =0
18.08.2021,14:37:33,$CRX:GA =624
18.08.2021,14:37:33,$CRX:Delay=0msec
18.08.2021,14:37:33,$CRX:Frequency=45.0MHz
18.08.2021,14:37:33,$HST:Receiver connected
18.08.2021,14:37:33,$CRX:Sweeplength=200
18.08.2021,14:37:33,$CRX:low_band_max=171MHz
18.08.2021,14:37:33,$CRX:mid_band_max=450MHz
18.08.2021,14:37:33,$CRX:high_band_max=863MHz
18.08.2021,14:37:33,$CRX:Idle=0
18.08.2021,14:37:35,$HST:Auto stop due to data loss.
18.08.2021,14:37:35,$HST:Measurement stop
18.08.2021,14:37:36,$HST:Measurement wait...
18.08.2021,14:37:36,$HST:Measurement halted
18.08.2021,14:37:37,$HST:Measurement idle
18.08.2021,14:37:37,$CRX:Stopped
18.08.2021,14:37:37,$HST:Measurement enable
18.08.2021,14:37:37,$CRX:AGC gain = 2.60V
18.08.2021,14:37:37,$CRX:Emitter BF199 = 0.20V
18.08.2021,14:37:37,$CRX:Analog Input = 11.23
18.08.2021,14:37:38,$HST:Check RS232-connection!
18.08.2021,14:37:41,$HST:Attempting Auto-Start
18.08.2021,14:37:41,$HST:Param. RCU due to START
18.08.2021,14:37:41,$HST:Actual focuscode 01
18.08.2021,14:37:42,$HST:Enable data transfer
18.08.2021,14:37:42,$HST:Continuous measurement
18.08.2021,14:37:42,$CRX:Started
18.08.2021,14:37:42,$HST:Start new FITS-file
18.08.2021,14:37:42,$HST:Continous measurement
18.08.2021,14:39:31,$HST:XYZ plot selected
18.08.2021,15:59:58,$HST:Measurement stop
18.08.2021,15:59:58,$HST:EOT (&) detected
18.08.2021,15:59:58,$HST:Measurement wait...
18.08.2021,15:59:58,$HST:Measurement halted
18.08.2021,15:59:58,$HST:Measurement stop
18.08.2021,15:59:58,$CRX:Stopped
18.08.2021,15:59:58,$HST:Measurement wait...
18.08.2021,15:59:59,$HST:Measurement halted
18.08.2021,15:59:59,$HST:Measurement idle
18.08.2021,15:59:59,$CRX:Stopped
18.08.2021,16:00:00,$HST:Autostart via scheduler
18.08.2021,16:00:00,$HST:Param. RCU due to START
18.08.2021,16:00:00,$HST:Actual focuscode 02
18.08.2021,16:00:00,$CRX:AGC gain = 2.52V
18.08.2021,16:00:00,$CRX:Emitter BF199 = 0.20V
18.08.2021,16:00:00,$CRX:Analog Input = 11.23
18.08.2021,16:00:00,$CRX:Started
18.08.2021,16:00:00,$HST:Enable data transfer
18.08.2021,16:00:00,$HST:Continuous measurement
18.08.2021,16:00:00,$HST:Start new FITS-file
18.08.2021,16:00:00,$HST:Continous measurement
18.08.2021,19:59:58,$HST:Measurement stop
18.08.2021,19:59:58,$HST:Measurement wait...
18.08.2021,19:59:58,$HST:EOT (&) detected
18.08.2021,19:59:58,$HST:Measurement halted
18.08.2021,19:59:58,$HST:Measurement stop
18.08.2021,19:59:58,$CRX:Stopped
18.08.2021,19:59:58,$HST:Measurement wait...
18.08.2021,19:59:59,$HST:Measurement halted
18.08.2021,19:59:59,$HST:Measurement idle
18.08.2021,19:59:59,$CRX:Stopped
18.08.2021,20:00:00,$HST:Measurement enable
18.08.2021,20:00:00,$CRX:AGC gain = 2.34V
18.08.2021,20:00:00,$CRX:Emitter BF199 = 0.20V
18.08.2021,20:00:00,$CRX:Analog Input = 11.23
18.08.2021,20:00:00,$HST:Autostart via scheduler
18.08.2021,20:00:00,$HST:Param. RCU due to START
18.08.2021,20:00:00,$HST:Actual focuscode 02
18.08.2021,20:00:00,$HST:Enable data transfer
18.08.2021,20:00:00,$HST:Continuous measurement
18.08.2021,20:00:00,$CRX:Started
18.08.2021,20:00:00,$HST:Start new FITS-file
18.08.2021,20:00:01,$HST:No more entries in scheduler.
18.08.2021,20:00:01,$HST:Continous measurement
19.08.2021,00:00:00,$HST:Midnight -> memo cleared
19.08.2021,00:00:00,$HST:EOF(logfile)