30.07.2019,06:59:41,$HST:Application just created
30.07.2019,06:59:41,$HST:SW-version 1.23, e-Callisto
30.07.2019,06:59:41,$HST:Configurationfile read
30.07.2019,06:59:41,$HST:Switched to automatic
30.07.2019,06:59:41,$HST:ATmega16 pre-configured
30.07.2019,06:59:41,$HST:Frequencyfile frq00255.cfg
30.07.2019,06:59:41,$HST:Callisto ready now...
30.07.2019,06:59:41,$HST:Measurement idle
30.07.2019,06:59:41,$HST:File scheduler.cfg read
30.07.2019,06:59:42,$HST:Measurement enable
30.07.2019,06:59:42,$CRX:AGC gain = 1.79V
30.07.2019,06:59:42,$CRX:Emitter BF199 = 0.12V
30.07.2019,06:59:42,$CRX:Analog Input = 9.24
30.07.2019,06:59:43,$HST:XY plot selected
30.07.2019,06:59:47,$HST:File FRQ00255.CFG read
30.07.2019,06:59:47,$HST:No calibration file found
30.07.2019,06:59:47,$HST:Plot buffer erased...
30.07.2019,06:59:47,$HST:Parametrisation RCU
30.07.2019,06:59:47,$CRX:ChargePump=On
30.07.2019,06:59:47,$HST:CD1316LV/IV detected
30.07.2019,06:59:47,$CRX:Debug=Off
30.07.2019,06:59:47,$CRX:Trigger=Intern
30.07.2019,06:59:47,$CRX:FPUcodex=58
30.07.2019,06:59:47,$CRX:GS =3376
30.07.2019,06:59:47,$CRX:GA =253
30.07.2019,06:59:47,$CRX:Delay=2msec
30.07.2019,06:59:47,$CRX:Frequency=45.0MHz
30.07.2019,06:59:47,$HST:Receiver connected
30.07.2019,06:59:47,$CRX:Sweeplength=200
30.07.2019,06:59:47,$CRX:low_band_max=171MHz
30.07.2019,06:59:47,$CRX:mid_band_max=450MHz
30.07.2019,06:59:47,$CRX:high_band_max=863MHz
30.07.2019,06:59:47,$CRX:Idle=0x
30.07.2019,06:59:47,$CRX:ChargePump=On
30.07.2019,06:59:47,$HST:CD1316LV/IV detected
30.07.2019,06:59:47,$CRX:Debug=Off
30.07.2019,06:59:47,$CRX:Trigger=Extern
30.07.2019,06:59:47,$CRX:FPUcodex=58
30.07.2019,06:59:47,$CRX:GS =3376
30.07.2019,06:59:47,$CRX:GA =253
30.07.2019,06:59:47,$CRX:Delay=2msec
30.07.2019,06:59:47,$CRX:Frequency=45.0MHz
30.07.2019,06:59:47,$HST:Receiver connected
30.07.2019,06:59:47,$CRX:Sweeplength=200
30.07.2019,06:59:47,$CRX:low_band_max=171MHz
30.07.2019,06:59:47,$CRX:mid_band_max=450MHz
30.07.2019,06:59:47,$CRX:high_band_max=863MHz
30.07.2019,06:59:47,$CRX:Idle=0x
30.07.2019,06:59:53,$HST:File FRQ00255.CFG read
30.07.2019,06:59:54,$HST:No calibration file found
30.07.2019,06:59:54,$HST:Plot buffer erased...
30.07.2019,06:59:54,$HST:Parametrisation RCU
30.07.2019,06:59:54,$HST:Param. RCU due to START
30.07.2019,06:59:54,$HST:Actual focuscode 01
30.07.2019,06:59:54,$HST:Enable data transfer
30.07.2019,06:59:54,$HST:Continuous measurement
30.07.2019,06:59:55,$HST:Start new FITS-file
30.07.2019,06:59:55,$HST:Continous measurement
30.07.2019,07:01:18,$HST:callisto.cfg watched
30.07.2019,07:01:25,$HST:All threads terminated
30.07.2019,07:01:25,$HST:This application closed