24.06.2019,05:48:27,$HST:Application just created
24.06.2019,05:48:27,$HST:SW-version 1.23, e-Callisto
24.06.2019,05:48:27,$HST:Configurationfile read
24.06.2019,05:48:27,$HST:Switched to automatic
24.06.2019,05:48:27,$HST:ATmega16 pre-configured
24.06.2019,05:48:27,$HST:Frequencyfile frq01090.cfg
24.06.2019,05:48:27,$HST:Callisto ready now...
24.06.2019,05:48:27,$HST:Measurement idle
24.06.2019,05:48:28,$HST:File scheduler.cfg read
24.06.2019,05:48:28,$HST:Measurement enable
24.06.2019,05:48:28,$CRX:AGC gain = 2.49V
24.06.2019,05:48:28,$CRX:Emitter BF199 = 0.15V
24.06.2019,05:48:28,$CRX:Analog Input = 9.24
24.06.2019,05:48:33,$HST:Switched to manual
24.06.2019,05:48:33,$HST:File FRQ01090.CFG read
24.06.2019,05:48:33,$HST:No calibration file found
24.06.2019,05:48:33,$HST:Plot buffer erased...
24.06.2019,05:48:33,$HST:Parametrisation RCU
24.06.2019,05:48:33,$CRX:ChargePump=On
24.06.2019,05:48:33,$HST:CD1316LV/IV detected
24.06.2019,05:48:33,$CRX:Debug=Off
24.06.2019,05:48:33,$CRX:Trigger=Extern
24.06.2019,05:48:33,$CRX:FPUcodex=3
24.06.2019,05:48:33,$CRX:GS =21317
24.06.2019,05:48:33,$CRX:GA =253
24.06.2019,05:48:33,$CRX:Delay=0msec
24.06.2019,05:48:33,$CRX:Frequency=45.0MHz
24.06.2019,05:48:33,$HST:Receiver connected
24.06.2019,05:48:33,$CRX:Sweeplength=200
24.06.2019,05:48:33,$CRX:low_band_max=171MHz
24.06.2019,05:48:33,$CRX:mid_band_max=450MHz
24.06.2019,05:48:33,$CRX:high_band_max=863MHz
24.06.2019,05:48:33,$CRX:Idle=0x
24.06.2019,05:48:33,$CRX:ChargePump=On
24.06.2019,05:48:33,$HST:CD1316LV/IV detected
24.06.2019,05:48:33,$CRX:Debug=Off
24.06.2019,05:48:33,$CRX:Trigger=Extern
24.06.2019,05:48:33,$CRX:FPUcodex=3
24.06.2019,05:48:33,$CRX:GS =21317
24.06.2019,05:48:33,$CRX:GA =624
24.06.2019,05:48:33,$CRX:Delay=0msec
24.06.2019,05:48:33,$CRX:Frequency=45.0MHz
24.06.2019,05:48:33,$HST:Receiver connected
24.06.2019,05:48:33,$CRX:Sweeplength=200
24.06.2019,05:48:33,$CRX:low_band_max=171MHz
24.06.2019,05:48:33,$CRX:mid_band_max=450MHz
24.06.2019,05:48:33,$CRX:high_band_max=863MHz
24.06.2019,05:48:33,$CRX:Idle=0x
24.06.2019,05:48:39,$HST:File FRQ01090.CFG read
24.06.2019,05:48:39,$HST:No calibration file found
24.06.2019,05:48:39,$HST:Plot buffer erased...
24.06.2019,05:48:39,$HST:Parametrisation RCU
24.06.2019,05:48:39,$CRX:ChargePump=On
24.06.2019,05:48:39,$HST:CD1316LV/IV detected
24.06.2019,05:48:39,$CRX:Debug=Off
24.06.2019,05:48:39,$CRX:Trigger=Extern
24.06.2019,05:48:39,$CRX:FPUcodex=3
24.06.2019,05:48:39,$CRX:GS =21317
24.06.2019,05:48:39,$CRX:GA =624
24.06.2019,05:48:39,$CRX:Delay=0msec
24.06.2019,05:48:39,$CRX:Frequency=45.0MHz
24.06.2019,05:48:39,$HST:Receiver connected
24.06.2019,05:48:39,$CRX:Sweeplength=200
24.06.2019,05:48:39,$CRX:low_band_max=171MHz
24.06.2019,05:48:39,$CRX:mid_band_max=450MHz
24.06.2019,05:48:39,$CRX:high_band_max=863MHz
24.06.2019,05:48:39,$CRX:Idle=0x
24.06.2019,05:48:39,$CRX:ChargePump=On
24.06.2019,05:48:39,$HST:CD1316LV/IV detected
24.06.2019,05:48:39,$CRX:Debug=Off
24.06.2019,05:48:39,$CRX:Trigger=Extern
24.06.2019,05:48:39,$CRX:FPUcodex=3
24.06.2019,05:48:39,$CRX:GS =21317
24.06.2019,05:48:39,$CRX:GA =624
24.06.2019,05:48:39,$CRX:Delay=0msec
24.06.2019,05:48:39,$CRX:Frequency=45.0MHz
24.06.2019,05:48:39,$HST:Receiver connected
24.06.2019,05:48:39,$CRX:Sweeplength=200
24.06.2019,05:48:39,$CRX:low_band_max=171MHz
24.06.2019,05:48:39,$CRX:mid_band_max=450MHz
24.06.2019,05:48:39,$CRX:high_band_max=863MHz
24.06.2019,05:48:39,$CRX:Idle=0x
24.06.2019,05:48:40,$HST:Param. RCU due to START
24.06.2019,05:48:40,$HST:Actual focuscode 03
24.06.2019,05:48:40,$HST:Enable data transfer
24.06.2019,05:48:40,$HST:Receiver calibration
24.06.2019,05:48:40,$CRX:Started
24.06.2019,05:48:40,$HST:Start new FITS-file
24.06.2019,05:48:40,$HST:Continous measurement
24.06.2019,05:48:44,$HST:XYZ plot selected
24.06.2019,06:34:07,$HST:XYZ plot selected
25.06.2019,00:00:00,$HST:Midnight -> memo cleared
25.06.2019,00:00:00,$HST:EOF(logfile)