24.06.2019,05:48:23,$HST:Application just created
24.06.2019,05:48:23,$HST:SW-version 1.23, e-Callisto
24.06.2019,05:48:23,$HST:Configurationfile read
24.06.2019,05:48:23,$HST:Switched to automatic
24.06.2019,05:48:23,$HST:ATmega16 pre-configured
24.06.2019,05:48:23,$HST:Frequencyfile frq01005.cfg
24.06.2019,05:48:23,$HST:Callisto ready now...
24.06.2019,05:48:24,$HST:Measurement idle
24.06.2019,05:48:24,$HST:File scheduler.cfg read
24.06.2019,05:48:24,$HST:Measurement enable
24.06.2019,05:48:24,$CRX:AGC gain = 2.42V
24.06.2019,05:48:24,$CRX:Emitter BF199 = 0.14V
24.06.2019,05:48:24,$CRX:Analog Input = 9.24
24.06.2019,05:48:29,$HST:File FRQ01005.CFG read
24.06.2019,05:48:29,$HST:No calibration file found
24.06.2019,05:48:29,$HST:Plot buffer erased...
24.06.2019,05:48:29,$HST:Parametrisation RCU
24.06.2019,05:48:30,$CRX:ChargePump=On
24.06.2019,05:48:30,$HST:CD1316LV/IV detected
24.06.2019,05:48:30,$CRX:Debug=Off
24.06.2019,05:48:30,$CRX:Trigger=Extern
24.06.2019,05:48:30,$CRX:FPUcodex=2
24.06.2019,05:48:30,$CRX:GS =3397
24.06.2019,05:48:30,$CRX:GA =253
24.06.2019,05:48:30,$CRX:Delay=0msec
24.06.2019,05:48:30,$CRX:Frequency=45.0MHz
24.06.2019,05:48:30,$HST:Receiver connected
24.06.2019,05:48:30,$CRX:Sweeplength=200
24.06.2019,05:48:30,$CRX:low_band_max=171MHz
24.06.2019,05:48:30,$CRX:mid_band_max=450MHz
24.06.2019,05:48:30,$CRX:high_band_max=863MHz
24.06.2019,05:48:30,$CRX:Idle=0x
24.06.2019,05:48:30,$CRX:ChargePump=On
24.06.2019,05:48:30,$HST:CD1316LV/IV detected
24.06.2019,05:48:30,$CRX:Debug=Off
24.06.2019,05:48:30,$CRX:Trigger=Extern
24.06.2019,05:48:30,$CRX:FPUcodex=2
24.06.2019,05:48:30,$CRX:GS =3397
24.06.2019,05:48:30,$CRX:GA =624
24.06.2019,05:48:30,$CRX:Delay=0msec
24.06.2019,05:48:30,$CRX:Frequency=45.0MHz
24.06.2019,05:48:30,$HST:Receiver connected
24.06.2019,05:48:30,$CRX:Sweeplength=200
24.06.2019,05:48:30,$CRX:low_band_max=171MHz
24.06.2019,05:48:30,$CRX:mid_band_max=450MHz
24.06.2019,05:48:30,$CRX:high_band_max=863MHz
24.06.2019,05:48:30,$CRX:Idle=0x
24.06.2019,05:48:32,$HST:Switched to manual
24.06.2019,05:48:35,$HST:File FRQ01005.CFG read
24.06.2019,05:48:35,$HST:No calibration file found
24.06.2019,05:48:35,$HST:Plot buffer erased...
24.06.2019,05:48:35,$HST:Parametrisation RCU
24.06.2019,05:48:35,$CRX:ChargePump=On
24.06.2019,05:48:35,$HST:CD1316LV/IV detected
24.06.2019,05:48:35,$CRX:Debug=Off
24.06.2019,05:48:35,$CRX:Trigger=Extern
24.06.2019,05:48:35,$CRX:FPUcodex=2
24.06.2019,05:48:35,$CRX:GS =3397
24.06.2019,05:48:35,$CRX:GA =624
24.06.2019,05:48:35,$CRX:Delay=0msec
24.06.2019,05:48:35,$CRX:Frequency=45.0MHz
24.06.2019,05:48:35,$HST:Receiver connected
24.06.2019,05:48:35,$CRX:Sweeplength=200
24.06.2019,05:48:35,$CRX:low_band_max=171MHz
24.06.2019,05:48:35,$CRX:mid_band_max=450MHz
24.06.2019,05:48:35,$CRX:high_band_max=863MHz
24.06.2019,05:48:35,$CRX:Idle=0x
24.06.2019,05:48:35,$CRX:ChargePump=On
24.06.2019,05:48:35,$HST:CD1316LV/IV detected
24.06.2019,05:48:35,$CRX:Debug=Off
24.06.2019,05:48:35,$CRX:Trigger=Extern
24.06.2019,05:48:35,$CRX:FPUcodex=2
24.06.2019,05:48:35,$CRX:GS =3397
24.06.2019,05:48:35,$CRX:GA =624
24.06.2019,05:48:35,$CRX:Delay=0msec
24.06.2019,05:48:35,$CRX:Frequency=45.0MHz
24.06.2019,05:48:35,$HST:Receiver connected
24.06.2019,05:48:35,$CRX:Sweeplength=200
24.06.2019,05:48:35,$CRX:low_band_max=171MHz
24.06.2019,05:48:35,$CRX:mid_band_max=450MHz
24.06.2019,05:48:35,$CRX:high_band_max=863MHz
24.06.2019,05:48:35,$CRX:Idle=0x
24.06.2019,05:48:36,$HST:Param. RCU due to START
24.06.2019,05:48:36,$HST:Actual focuscode 02
24.06.2019,05:48:36,$HST:Enable data transfer
24.06.2019,05:48:36,$HST:Receiver calibration
24.06.2019,05:48:36,$CRX:Started
24.06.2019,05:48:36,$HST:Start new FITS-file
24.06.2019,05:48:37,$HST:Continous measurement
24.06.2019,05:48:41,$HST:XYZ plot selected
24.06.2019,05:48:43,$HST:XYZ plot hidden
24.06.2019,06:34:16,$HST:XYZ plot selected
25.06.2019,00:00:00,$HST:Midnight -> memo cleared
25.06.2019,00:00:00,$HST:EOF(logfile)