04.06.2019,12:15:34,$HST:Application just created
04.06.2019,12:15:34,$HST:SW-version 1.23, e-Callisto
04.06.2019,12:15:34,$HST:Configurationfile read
04.06.2019,12:15:34,$HST:Switched to automatic
04.06.2019,12:15:34,$HST:ATmega16 pre-configured
04.06.2019,12:15:34,$HST:Frequencyfile frq01090.cfg
04.06.2019,12:15:34,$HST:Callisto ready now...
04.06.2019,12:15:34,$HST:Measurement idle
04.06.2019,12:15:35,$HST:File scheduler.cfg read
04.06.2019,12:15:35,$HST:Measurement enable
04.06.2019,12:15:35,$CRX:AGC gain = 2.49V
04.06.2019,12:15:35,$CRX:Emitter BF199 = 0.15V
04.06.2019,12:15:35,$CRX:Analog Input = 9.24
04.06.2019,12:15:40,$HST:File FRQ01090.CFG read
04.06.2019,12:15:40,$HST:No calibration file found
04.06.2019,12:15:40,$HST:Plot buffer erased...
04.06.2019,12:15:40,$HST:Parametrisation RCU
04.06.2019,12:15:40,$CRX:ChargePump=On
04.06.2019,12:15:40,$HST:CD1316LV/IV detected
04.06.2019,12:15:40,$CRX:Debug=Off
04.06.2019,12:15:40,$CRX:Trigger=Extern
04.06.2019,12:15:40,$CRX:FPUcodex=3
04.06.2019,12:15:40,$CRX:GS =3397
04.06.2019,12:15:40,$CRX:GA =253
04.06.2019,12:15:40,$CRX:Delay=0msec
04.06.2019,12:15:40,$CRX:Frequency=45.0MHz
04.06.2019,12:15:40,$HST:Receiver connected
04.06.2019,12:15:40,$CRX:Sweeplength=200
04.06.2019,12:15:40,$CRX:low_band_max=171MHz
04.06.2019,12:15:40,$CRX:mid_band_max=450MHz
04.06.2019,12:15:40,$CRX:high_band_max=863MHz
04.06.2019,12:15:40,$CRX:Idle=0x
04.06.2019,12:15:40,$CRX:ChargePump=On
04.06.2019,12:15:40,$HST:CD1316LV/IV detected
04.06.2019,12:15:40,$CRX:Debug=Off
04.06.2019,12:15:40,$CRX:Trigger=Extern
04.06.2019,12:15:40,$CRX:FPUcodex=3
04.06.2019,12:15:40,$CRX:GS =3397
04.06.2019,12:15:40,$CRX:GA =624
04.06.2019,12:15:40,$CRX:Delay=0msec
04.06.2019,12:15:40,$CRX:Frequency=45.0MHz
04.06.2019,12:15:40,$HST:Receiver connected
04.06.2019,12:15:40,$CRX:Sweeplength=200
04.06.2019,12:15:40,$CRX:low_band_max=171MHz
04.06.2019,12:15:40,$CRX:mid_band_max=450MHz
04.06.2019,12:15:40,$CRX:high_band_max=863MHz
04.06.2019,12:15:40,$CRX:Idle=0x
04.06.2019,12:15:43,$HST:Param. RCU due to START
04.06.2019,12:15:43,$HST:Actual focuscode 03
04.06.2019,12:15:43,$HST:Enable data transfer
04.06.2019,12:15:43,$HST:Receiver calibration
04.06.2019,12:15:43,$CRX:Started
04.06.2019,12:15:43,$HST:Start new FITS-file
04.06.2019,12:15:43,$HST:Continous measurement
04.06.2019,12:15:43,$HST:XYZ plot selected
04.06.2019,18:44:58,$HST:Measurement stop
04.06.2019,18:44:58,$HST:Measurement wait...
04.06.2019,18:44:58,$HST:EOT (&) detected
04.06.2019,18:44:58,$HST:Measurement halted
04.06.2019,18:44:58,$HST:Measurement stop
04.06.2019,18:44:58,$CRX:Stopped
04.06.2019,18:44:58,$HST:Measurement wait...
04.06.2019,18:44:59,$HST:Measurement halted
04.06.2019,18:44:59,$HST:Measurement idle
04.06.2019,18:44:59,$CRX:Stopped
04.06.2019,18:45:00,$HST:Measurement enable
04.06.2019,18:45:00,$CRX:AGC gain = 2.49V
04.06.2019,18:45:00,$CRX:Emitter BF199 = 0.15V
04.06.2019,18:45:00,$CRX:Analog Input = 9.24
04.06.2019,18:45:01,$HST:No more entries in scheduler.
05.06.2019,00:00:00,$HST:Midnight -> memo cleared
05.06.2019,00:00:00,$HST:EOF(logfile)