16.08.2018,17:45:22,$HST:Application just created
16.08.2018,17:45:22,$HST:SW-version 1.23, e-Callisto
16.08.2018,17:45:22,$HST:Configurationfile read
16.08.2018,17:45:22,$HST:Switched to automatic
16.08.2018,17:45:22,$HST:ATmega16 pre-configured
16.08.2018,17:45:22,$HST:Frequencyfile frq01005.cfg
16.08.2018,17:45:22,$HST:Callisto ready now...
16.08.2018,17:45:23,$HST:Measurement idle
16.08.2018,17:45:23,$HST:File scheduler.cfg read
16.08.2018,17:45:23,$HST:Measurement enable
16.08.2018,17:45:23,$CRX:AGC gain = 2.42V
16.08.2018,17:45:23,$CRX:Emitter BF199 = 0.14V
16.08.2018,17:45:23,$CRX:Analog Input = 9.24
16.08.2018,17:45:26,$HST:File FRQ01005.CFG read
16.08.2018,17:45:26,$HST:No calibration file found
16.08.2018,17:45:26,$HST:Plot buffer erased...
16.08.2018,17:45:26,$HST:Parametrisation RCU
16.08.2018,17:45:26,$CRX:ChargePump=On
16.08.2018,17:45:26,$HST:CD1316LV/IV detected
16.08.2018,17:45:26,$CRX:Debug=Off
16.08.2018,17:45:26,$CRX:Trigger=Extern
16.08.2018,17:45:26,$CRX:FPUcodex=2
16.08.2018,17:45:26,$CRX:GS =3377
16.08.2018,17:45:26,$CRX:GA =253
16.08.2018,17:45:26,$CRX:Delay=0msec
16.08.2018,17:45:26,$CRX:Frequency=45.0MHz
16.08.2018,17:45:26,$HST:Receiver connected
16.08.2018,17:45:26,$CRX:Sweeplength=200
16.08.2018,17:45:26,$CRX:low_band_max=171MHz
16.08.2018,17:45:26,$CRX:mid_band_max=450MHz
16.08.2018,17:45:26,$CRX:high_band_max=863MHz
16.08.2018,17:45:26,$CRX:Idle=0x
16.08.2018,17:45:26,$CRX:ChargePump=On
16.08.2018,17:45:26,$HST:CD1316LV/IV detected
16.08.2018,17:45:26,$CRX:Debug=Off
16.08.2018,17:45:26,$CRX:Trigger=Extern
16.08.2018,17:45:26,$CRX:FPUcodex=2
16.08.2018,17:45:26,$CRX:GS =3377
16.08.2018,17:45:26,$CRX:GA =624
16.08.2018,17:45:26,$CRX:Delay=0msec
16.08.2018,17:45:26,$CRX:Frequency=45.0MHz
16.08.2018,17:45:26,$HST:Receiver connected
16.08.2018,17:45:26,$CRX:Sweeplength=200
16.08.2018,17:45:26,$CRX:low_band_max=171MHz
16.08.2018,17:45:26,$CRX:mid_band_max=450MHz
16.08.2018,17:45:26,$CRX:high_band_max=863MHz
16.08.2018,17:45:26,$CRX:Idle=0x
16.08.2018,17:45:34,$HST:Switched to manual
16.08.2018,17:45:35,$HST:Param. RCU due to START
16.08.2018,17:45:35,$HST:Actual focuscode 02
16.08.2018,17:45:36,$HST:Enable data transfer
16.08.2018,17:45:36,$HST:Receiver calibration
16.08.2018,17:45:36,$CRX:Started
16.08.2018,17:45:36,$HST:Start new FITS-file
16.08.2018,17:45:36,$HST:Continous measurement
16.08.2018,17:45:37,$HST:XYZ plot selected
17.08.2018,00:00:00,$HST:Midnight -> memo cleared
17.08.2018,00:00:00,$HST:EOF(logfile)