17.07.2018,06:45:48,$HST:Application just created
17.07.2018,06:45:48,$HST:SW-version 1.23, e-Callisto
17.07.2018,06:45:48,$HST:Configurationfile read
17.07.2018,06:45:48,$HST:Switched to automatic
17.07.2018,06:45:48,$HST:ATmega16 pre-configured
17.07.2018,06:45:48,$HST:Frequencyfile frq01005.cfg
17.07.2018,06:45:48,$HST:Callisto ready now...
17.07.2018,06:45:49,$HST:Measurement idle
17.07.2018,06:45:49,$HST:File scheduler.cfg read
17.07.2018,06:45:49,$HST:Measurement enable
17.07.2018,06:45:49,$CRX:AGC gain = 2.42V
17.07.2018,06:45:49,$CRX:Emitter BF199 = 0.14V
17.07.2018,06:45:49,$CRX:Analog Input = 9.24
17.07.2018,06:45:55,$HST:File FRQ01005.CFG read
17.07.2018,06:45:55,$HST:No calibration file found
17.07.2018,06:45:55,$HST:Plot buffer erased...
17.07.2018,06:45:55,$HST:Parametrisation RCU
17.07.2018,06:45:55,$CRX:ChargePump=On
17.07.2018,06:45:55,$HST:CD1316LV/IV detected
17.07.2018,06:45:55,$CRX:Debug=Off
17.07.2018,06:45:55,$CRX:Trigger=Extern
17.07.2018,06:45:55,$CRX:FPUcodex=2
17.07.2018,06:45:55,$CRX:GS =3385
17.07.2018,06:45:55,$CRX:GA =253
17.07.2018,06:45:55,$CRX:Delay=0msec
17.07.2018,06:45:55,$CRX:Frequency=45.0MHz
17.07.2018,06:45:55,$HST:Receiver connected
17.07.2018,06:45:55,$CRX:Sweeplength=200
17.07.2018,06:45:55,$CRX:low_band_max=171MHz
17.07.2018,06:45:55,$CRX:mid_band_max=450MHz
17.07.2018,06:45:55,$CRX:high_band_max=863MHz
17.07.2018,06:45:55,$CRX:Idle=0x
17.07.2018,06:45:55,$CRX:ChargePump=On
17.07.2018,06:45:55,$HST:CD1316LV/IV detected
17.07.2018,06:45:55,$CRX:Debug=Off
17.07.2018,06:45:55,$CRX:Trigger=Extern
17.07.2018,06:45:55,$CRX:FPUcodex=2
17.07.2018,06:45:55,$CRX:GS =3385
17.07.2018,06:45:55,$CRX:GA =624
17.07.2018,06:45:55,$CRX:Delay=0msec
17.07.2018,06:45:55,$CRX:Frequency=45.0MHz
17.07.2018,06:45:55,$HST:Receiver connected
17.07.2018,06:45:55,$CRX:Sweeplength=200
17.07.2018,06:45:55,$CRX:low_band_max=171MHz
17.07.2018,06:45:55,$CRX:mid_band_max=450MHz
17.07.2018,06:45:55,$CRX:high_band_max=863MHz
17.07.2018,06:45:55,$CRX:Idle=0x
17.07.2018,06:45:56,$HST:XY plot selected
17.07.2018,06:46:00,$HST:File FRQ01005.CFG read
17.07.2018,06:46:00,$HST:No calibration file found
17.07.2018,06:46:00,$HST:Plot buffer erased...
17.07.2018,06:46:00,$HST:Parametrisation RCU
17.07.2018,06:46:01,$CRX:ChargePump=On
17.07.2018,06:46:01,$HST:CD1316LV/IV detected
17.07.2018,06:46:01,$CRX:Debug=Off
17.07.2018,06:46:01,$CRX:Trigger=Extern
17.07.2018,06:46:01,$CRX:FPUcodex=2
17.07.2018,06:46:01,$CRX:GS =3385
17.07.2018,06:46:01,$CRX:GA =624
17.07.2018,06:46:01,$CRX:Delay=0msec
17.07.2018,06:46:01,$CRX:Frequency=45.0MHz
17.07.2018,06:46:01,$HST:Receiver connected
17.07.2018,06:46:01,$CRX:Sweeplength=200
17.07.2018,06:46:01,$CRX:low_band_max=171MHz
17.07.2018,06:46:01,$CRX:mid_band_max=450MHz
17.07.2018,06:46:01,$CRX:high_band_max=863MHz
17.07.2018,06:46:01,$CRX:Idle=0x
17.07.2018,06:46:01,$CRX:ChargePump=On
17.07.2018,06:46:01,$HST:CD1316LV/IV detected
17.07.2018,06:46:01,$CRX:Debug=Off
17.07.2018,06:46:01,$CRX:Trigger=Extern
17.07.2018,06:46:01,$CRX:FPUcodex=2
17.07.2018,06:46:01,$CRX:GS =3385
17.07.2018,06:46:01,$CRX:GA =624
17.07.2018,06:46:01,$CRX:Delay=0msec
17.07.2018,06:46:01,$CRX:Frequency=45.0MHz
17.07.2018,06:46:01,$HST:Receiver connected
17.07.2018,06:46:01,$CRX:Sweeplength=200
17.07.2018,06:46:01,$CRX:low_band_max=171MHz
17.07.2018,06:46:01,$CRX:mid_band_max=450MHz
17.07.2018,06:46:01,$CRX:high_band_max=863MHz
17.07.2018,06:46:01,$CRX:Idle=0x
17.07.2018,06:46:01,$HST:XYZ plot selected
17.07.2018,06:46:10,$HST:Switched to manual
17.07.2018,06:46:13,$HST:Param. RCU due to START
17.07.2018,06:46:13,$HST:Actual focuscode 02
17.07.2018,06:46:13,$HST:Enable data transfer
17.07.2018,06:46:13,$HST:Receiver calibration
17.07.2018,06:46:13,$CRX:Started
17.07.2018,06:46:14,$HST:Start new FITS-file
17.07.2018,06:46:14,$HST:Continous measurement
18.07.2018,00:00:00,$HST:Midnight -> memo cleared
18.07.2018,00:00:00,$HST:EOF(logfile)