05.01.2018,13:41:37,$HST:Application just created
05.01.2018,13:41:37,$HST:SW-version 1.23, e-Callisto
05.01.2018,13:41:37,$HST:Configurationfile read
05.01.2018,13:41:37,$HST:Switched to automatic
05.01.2018,13:41:37,$HST:ATmega16 pre-configured
05.01.2018,13:41:37,$HST:Frequencyfile frq01005.cfg
05.01.2018,13:41:37,$HST:Callisto ready now...
05.01.2018,13:41:37,$HST:Measurement idle
05.01.2018,13:41:37,$HST:File scheduler.cfg read
05.01.2018,13:41:37,$HST:Measurement enable
05.01.2018,13:41:37,$CRX:AGC gain = 0.00V
05.01.2018,13:41:37,$CRX:Emitter BF199 = 0.14V
05.01.2018,13:41:37,$CRX:Analog Input = 9.24
05.01.2018,13:41:43,$HST:File FRQ01005.CFG read
05.01.2018,13:41:43,$HST:No calibration file found
05.01.2018,13:41:43,$HST:Plot buffer erased...
05.01.2018,13:41:43,$HST:Parametrisation RCU
05.01.2018,13:41:43,$CRX:ChargePump=On
05.01.2018,13:41:43,$HST:CD1316LV/IV detected
05.01.2018,13:41:43,$CRX:Debug=Off
05.01.2018,13:41:43,$CRX:Trigger=No
05.01.2018,13:41:43,$CRX:FPUcodex=0
05.01.2018,13:41:43,$CRX:GS =13
05.01.2018,13:41:43,$CRX:GA =253
05.01.2018,13:41:43,$CRX:Delay=0msec
05.01.2018,13:41:43,$CRX:Frequency=0.0MHz
05.01.2018,13:41:43,$HST:Receiver connected
05.01.2018,13:41:43,$CRX:Sweeplength=0
05.01.2018,13:41:43,$CRX:low_band_max=171MHz
05.01.2018,13:41:43,$CRX:mid_band_max=450MHz
05.01.2018,13:41:43,$CRX:high_band_max=863MHz
05.01.2018,13:41:43,$CRX:Idle=0x
05.01.2018,13:41:43,$CRX:ChargePump=On
05.01.2018,13:41:43,$HST:CD1316LV/IV detected
05.01.2018,13:41:43,$CRX:Debug=Off
05.01.2018,13:41:43,$CRX:Trigger=Extern
05.01.2018,13:41:43,$CRX:FPUcodex=0
05.01.2018,13:41:43,$CRX:GS =13
05.01.2018,13:41:43,$CRX:GA =624
05.01.2018,13:41:43,$CRX:Delay=0msec
05.01.2018,13:41:43,$CRX:Frequency=45.0MHz
05.01.2018,13:41:43,$HST:Receiver connected
05.01.2018,13:41:43,$CRX:Sweeplength=200
05.01.2018,13:41:43,$CRX:low_band_max=171MHz
05.01.2018,13:41:43,$CRX:mid_band_max=450MHz
05.01.2018,13:41:43,$CRX:high_band_max=863MHz
05.01.2018,13:41:43,$CRX:Idle=0x
05.01.2018,13:41:46,$HST:Switched to manual
05.01.2018,13:41:49,$HST:XY plot selected
05.01.2018,13:41:55,$HST:Param. RCU due to START
05.01.2018,13:41:55,$HST:Actual focuscode 02
05.01.2018,13:41:55,$HST:Enable data transfer
05.01.2018,13:41:55,$HST:Receiver calibration
05.01.2018,13:41:55,$CRX:Started
05.01.2018,13:41:55,$HST:Start new FITS-file
05.01.2018,13:41:55,$HST:Continous measurement
06.01.2018,00:00:00,$HST:Midnight -> memo cleared
06.01.2018,00:00:00,$HST:EOF(logfile)