26.10.2017,07:20:12,$HST:Application just created
26.10.2017,07:20:12,$HST:SW-version 1.18, e-Callisto
26.10.2017,07:20:12,$HST:Configurationfile read
26.10.2017,07:20:12,$HST:Switched to automatic
26.10.2017,07:20:12,$HST:ATmega16 pre-configured
26.10.2017,07:20:12,$HST:Frequencyfile frq01005.cfg
26.10.2017,07:20:12,$HST:Callisto ready now...
26.10.2017,07:20:12,$HST:Measurement idle
26.10.2017,07:20:12,$HST:File scheduler.cfg read
26.10.2017,07:20:12,$HST:Measurement enable
26.10.2017,07:20:12,$CRX:AGC gain = 2.42V
26.10.2017,07:20:12,$CRX:Emitter BF199 = 0.14V
26.10.2017,07:20:12,$CRX:Analog Input = 9.24
26.10.2017,07:20:18,$HST:File frq01005.cfg read
26.10.2017,07:20:18,$HST:No calibration file found
26.10.2017,07:20:18,$HST:Plot buffer erased...
26.10.2017,07:20:18,$HST:Parametrisation RCU
26.10.2017,07:20:19,$CRX:ChargePump=On
26.10.2017,07:20:19,$HST:CD1316LV/IV detected
26.10.2017,07:20:19,$CRX:Debug=Off
26.10.2017,07:20:19,$CRX:Trigger=Extern
26.10.2017,07:20:19,$CRX:FPUcodex=2
26.10.2017,07:20:19,$CRX:GS =12340
26.10.2017,07:20:19,$CRX:GA =253
26.10.2017,07:20:19,$CRX:Delay=0msec
26.10.2017,07:20:19,$CRX:Frequency=45.0MHz
26.10.2017,07:20:19,$HST:Receiver connected
26.10.2017,07:20:19,$CRX:Sweeplength=200
26.10.2017,07:20:19,$CRX:low_band_max=171MHz
26.10.2017,07:20:19,$CRX:mid_band_max=450MHz
26.10.2017,07:20:19,$CRX:high_band_max=863MHz
26.10.2017,07:20:19,$CRX:Idle=0x
26.10.2017,07:20:19,$CRX:ChargePump=On
26.10.2017,07:20:19,$HST:CD1316LV/IV detected
26.10.2017,07:20:19,$CRX:Debug=Off
26.10.2017,07:20:19,$CRX:Trigger=Extern
26.10.2017,07:20:19,$CRX:FPUcodex=2
26.10.2017,07:20:19,$CRX:GS =12340
26.10.2017,07:20:19,$CRX:GA =624
26.10.2017,07:20:19,$CRX:Delay=0msec
26.10.2017,07:20:19,$CRX:Frequency=45.0MHz
26.10.2017,07:20:19,$HST:Receiver connected
26.10.2017,07:20:19,$CRX:Sweeplength=200
26.10.2017,07:20:19,$CRX:low_band_max=171MHz
26.10.2017,07:20:19,$CRX:mid_band_max=450MHz
26.10.2017,07:20:19,$CRX:high_band_max=863MHz
26.10.2017,07:20:19,$CRX:Idle=0x
26.10.2017,07:20:22,$HST:XY plot selected
26.10.2017,07:20:28,$HST:Param. RCU due to START
26.10.2017,07:20:28,$HST:Actual focuscode 02
26.10.2017,07:20:28,$HST:Enable data transfer
26.10.2017,07:20:28,$HST:Receiver calibration
26.10.2017,07:20:28,$CRX:Started
26.10.2017,07:20:29,$HST:Start new FITS-file
26.10.2017,07:20:29,$HST:Continous measurement
26.10.2017,07:21:59,$HST:XY plot selected
26.10.2017,07:22:02,$HST:XYZ plot selected
26.10.2017,07:29:58,$HST:Measurement stop
26.10.2017,07:29:58,$HST:Measurement wait...
26.10.2017,07:29:58,$HST:EOT (&) detected
26.10.2017,07:29:58,$HST:Measurement halted
26.10.2017,07:29:58,$HST:Measurement stop
26.10.2017,07:29:58,$CRX:Stopped
26.10.2017,07:29:59,$HST:Measurement wait...
26.10.2017,07:29:59,$HST:Measurement halted
26.10.2017,07:30:00,$HST:Measurement idle
26.10.2017,07:30:00,$CRX:Stopped
26.10.2017,07:30:00,$HST:Autostart via scheduler
26.10.2017,07:30:00,$HST:Param. RCU due to START
26.10.2017,07:30:00,$HST:Actual focuscode 02
26.10.2017,07:30:00,$CRX:AGC gain = 2.42V
26.10.2017,07:30:00,$CRX:Emitter BF199 = 0.14V
26.10.2017,07:30:00,$CRX:Analog Input = 9.24
26.10.2017,07:30:00,$HST:Enable data transfer
26.10.2017,07:30:00,$HST:Receiver calibration
26.10.2017,07:30:00,$CRX:Started
26.10.2017,07:30:00,$HST:Start new FITS-file
26.10.2017,07:30:00,$HST:Continous measurement
26.10.2017,09:46:32,$HST:Yt plot selected
26.10.2017,09:46:34,$HST:XY plot selected
26.10.2017,09:46:37,$HST:XYZ plot selected
26.10.2017,09:46:50,$HST:XYZ plot selected
26.10.2017,09:46:51,$HST:XYZ plot hidden
26.10.2017,09:46:51,$HST:XY plot hidden
26.10.2017,09:46:52,$HST:Yt plot hidden
26.10.2017,11:59:58,$HST:Measurement stop
26.10.2017,11:59:58,$HST:Measurement wait...
26.10.2017,11:59:58,$HST:EOT (&) detected
26.10.2017,11:59:58,$HST:Measurement halted
26.10.2017,11:59:58,$HST:Measurement stop
26.10.2017,11:59:58,$CRX:Stopped
26.10.2017,11:59:58,$HST:Measurement wait...
26.10.2017,11:59:59,$HST:Measurement halted
26.10.2017,11:59:59,$HST:Measurement idle
26.10.2017,11:59:59,$CRX:Stopped
26.10.2017,12:00:00,$HST:Measurement enable
26.10.2017,12:00:00,$CRX:AGC gain = 2.42V
26.10.2017,12:00:00,$CRX:Emitter BF199 = 0.14V
26.10.2017,12:00:00,$CRX:Analog Input = 9.24
26.10.2017,12:00:00,$HST:Autostart via scheduler
26.10.2017,12:00:00,$HST:Param. RCU due to START
26.10.2017,12:00:00,$HST:Actual focuscode 02
26.10.2017,12:00:00,$HST:Enable data transfer
26.10.2017,12:00:00,$HST:Receiver calibration
26.10.2017,12:00:00,$CRX:Started
26.10.2017,12:00:00,$HST:Start new FITS-file
26.10.2017,12:00:00,$HST:Continous measurement
26.10.2017,18:44:58,$HST:Measurement stop
26.10.2017,18:44:58,$HST:Measurement wait...
26.10.2017,18:44:58,$HST:EOT (&) detected
26.10.2017,18:44:58,$HST:Measurement halted
26.10.2017,18:44:58,$HST:Measurement stop
26.10.2017,18:44:58,$CRX:Stopped
26.10.2017,18:44:58,$HST:Measurement wait...
26.10.2017,18:44:59,$HST:Measurement halted
26.10.2017,18:44:59,$HST:Measurement idle
26.10.2017,18:44:59,$CRX:Stopped
26.10.2017,18:45:00,$HST:Measurement enable
26.10.2017,18:45:00,$CRX:AGC gain = 2.42V
26.10.2017,18:45:00,$CRX:Emitter BF199 = 0.14V
26.10.2017,18:45:00,$CRX:Analog Input = 9.24
26.10.2017,18:45:01,$HST:No more entries in scheduler.
27.10.2017,00:00:00,$HST:Midnight -> memo cleared
27.10.2017,00:00:00,$HST:EOF(logfile)