21.09.2017,07:47:53,$HST:Application just created
21.09.2017,07:47:53,$HST:SW-version 1.16, e-Callisto
21.09.2017,07:47:53,$HST:Configurationfile read
21.09.2017,07:47:53,$HST:Switched to automatic
21.09.2017,07:47:53,$HST:ATmega16 pre-configured
21.09.2017,07:47:53,$HST:Frequencyfile frq00255.cfg
21.09.2017,07:47:53,$HST:Callisto ready now...
21.09.2017,07:47:54,$HST:Measurement idle
21.09.2017,07:47:54,$HST:File scheduler.cfg read
21.09.2017,07:47:54,$HST:Measurement enable
21.09.2017,07:47:54,$CRX:AGC gain = 1.79V
21.09.2017,07:47:54,$CRX:Emitter BF199 = 0.12V
21.09.2017,07:47:54,$CRX:Analog Input = 9.24
21.09.2017,07:47:59,$HST:File frq00255.cfg read
21.09.2017,07:48:00,$HST:No calibration file found
21.09.2017,07:48:00,$HST:Plot buffer erased...
21.09.2017,07:48:00,$HST:Parametrisation RCU
21.09.2017,07:48:00,$CRX:ChargePump=On
21.09.2017,07:48:00,$HST:CD1316LV/IV detected
21.09.2017,07:48:00,$CRX:Debug=Off
21.09.2017,07:48:00,$CRX:Trigger=Soft
21.09.2017,07:48:00,$CRX:FPUcodex=58
21.09.2017,07:48:00,$CRX:GS =3382
21.09.2017,07:48:00,$CRX:GA =253
21.09.2017,07:48:00,$CRX:Delay=2msec
21.09.2017,07:48:00,$CRX:Frequency=870.0MHz
21.09.2017,07:48:00,$HST:Receiver connected
21.09.2017,07:48:00,$CRX:Sweeplength=200
21.09.2017,07:48:00,$CRX:low_band_max=171MHz
21.09.2017,07:48:00,$CRX:mid_band_max=450MHz
21.09.2017,07:48:00,$CRX:high_band_max=863MHz
21.09.2017,07:48:00,$CRX:Idle=0x
21.09.2017,07:48:00,$CRX:ChargePump=On
21.09.2017,07:48:00,$HST:CD1316LV/IV detected
21.09.2017,07:48:00,$CRX:Debug=Off
21.09.2017,07:48:00,$CRX:Trigger=Extern
21.09.2017,07:48:00,$CRX:FPUcodex=58
21.09.2017,07:48:00,$CRX:GS =3382
21.09.2017,07:48:00,$CRX:GA =624
21.09.2017,07:48:00,$CRX:Delay=2msec
21.09.2017,07:48:00,$CRX:Frequency=45.0MHz
21.09.2017,07:48:00,$HST:Receiver connected
21.09.2017,07:48:00,$CRX:Sweeplength=200
21.09.2017,07:48:00,$CRX:low_band_max=171MHz
21.09.2017,07:48:00,$CRX:mid_band_max=450MHz
21.09.2017,07:48:00,$CRX:high_band_max=863MHz
21.09.2017,07:48:00,$CRX:Idle=0x
21.09.2017,07:48:06,$HST:XYZ plot selected
21.09.2017,07:48:14,$HST:scheduler.cfg watched
21.09.2017,07:48:33,$HST:Param. RCU due to START
21.09.2017,07:48:33,$HST:Actual focuscode 01
21.09.2017,07:48:33,$HST:Enable data transfer
21.09.2017,07:48:33,$HST:Continuous measurement
21.09.2017,07:48:33,$CRX:Started
21.09.2017,07:48:33,$HST:Start new FITS-file
21.09.2017,07:48:34,$HST:Continous measurement
21.09.2017,07:49:16,$HST:scheduler.cfg watched
21.09.2017,07:59:58,$HST:Measurement stop
21.09.2017,07:59:58,$HST:FITS #1 200rows x 2737cols
21.09.2017,07:59:58,$HST:Measurement wait...
21.09.2017,07:59:58,$HST:EOT (&) detected
21.09.2017,07:59:58,$HST:Measurement halted
21.09.2017,07:59:58,$HST:Measurement stop
21.09.2017,07:59:58,$CRX:Stopped
21.09.2017,07:59:59,$HST:Measurement wait...
21.09.2017,07:59:59,$HST:Measurement halted
21.09.2017,07:59:59,$HST:Measurement idle
21.09.2017,07:59:59,$CRX:Stopped
21.09.2017,08:00:00,$HST:Autostart via scheduler
21.09.2017,08:00:00,$HST:Param. RCU due to START
21.09.2017,08:00:00,$HST:Actual focuscode 58
21.09.2017,08:00:00,$CRX:AGC gain = 1.79V
21.09.2017,08:00:00,$CRX:Emitter BF199 = 0.12V
21.09.2017,08:00:00,$CRX:Analog Input = 9.24
21.09.2017,08:00:00,$HST:Enable data transfer
21.09.2017,08:00:00,$HST:Continuous measurement
21.09.2017,08:00:00,$CRX:Started
21.09.2017,08:00:00,$HST:Start new FITS-file
21.09.2017,08:00:00,$HST:Continous measurement
21.09.2017,08:15:00,$HST:FITS #2 200rows x 3600cols
21.09.2017,08:30:00,$HST:FITS #3 200rows x 3600cols
21.09.2017,08:45:00,$HST:FITS #4 200rows x 3600cols
21.09.2017,09:00:00,$HST:FITS #5 200rows x 3600cols
21.09.2017,09:15:00,$HST:FITS #6 200rows x 3600cols
21.09.2017,09:30:00,$HST:FITS #7 200rows x 3600cols
21.09.2017,09:45:00,$HST:FITS #8 200rows x 3600cols
21.09.2017,10:00:00,$HST:FITS #9 200rows x 3600cols
21.09.2017,10:15:00,$HST:FITS #10 200rows x 3600cols
21.09.2017,10:30:00,$HST:FITS #11 200rows x 3600cols
21.09.2017,10:45:00,$HST:FITS #12 200rows x 3600cols
21.09.2017,10:48:06,$HST:All threads terminated
21.09.2017,10:48:06,$HST:This application closed