20.06.2017,06:27:56,$HST:Application just created
20.06.2017,06:27:56,$HST:SW-version 1.18, e-Callisto
20.06.2017,06:27:56,$HST:Configurationfile read
20.06.2017,06:27:56,$HST:Switched to automatic
20.06.2017,06:27:56,$HST:ATmega16 pre-configured
20.06.2017,06:27:56,$HST:Frequencyfile frq01005.cfg
20.06.2017,06:27:56,$HST:Callisto ready now...
20.06.2017,06:27:56,$HST:Measurement idle
20.06.2017,06:27:56,$HST:File scheduler.cfg read
20.06.2017,06:27:57,$HST:Measurement enable
20.06.2017,06:27:57,$CRX:AGC gain = 2.42V
20.06.2017,06:27:57,$CRX:Emitter BF199 = 0.14V
20.06.2017,06:27:57,$CRX:Analog Input = 9.24
20.06.2017,06:28:02,$HST:File frq01005.cfg read
20.06.2017,06:28:02,$HST:No calibration file found
20.06.2017,06:28:02,$HST:Plot buffer erased...
20.06.2017,06:28:02,$HST:Parametrisation RCU
20.06.2017,06:28:02,$CRX:ChargePump=On
20.06.2017,06:28:02,$HST:CD1316LV/IV detected
20.06.2017,06:28:02,$CRX:Debug=Off
20.06.2017,06:28:02,$CRX:Trigger=Extern
20.06.2017,06:28:02,$CRX:FPUcodex=2
20.06.2017,06:28:02,$CRX:GS =61764
20.06.2017,06:28:02,$CRX:GA =253
20.06.2017,06:28:02,$CRX:Delay=0msec
20.06.2017,06:28:02,$CRX:Frequency=45.0MHz
20.06.2017,06:28:02,$HST:Receiver connected
20.06.2017,06:28:02,$CRX:Sweeplength=200
20.06.2017,06:28:02,$CRX:low_band_max=171MHz
20.06.2017,06:28:02,$CRX:mid_band_max=450MHz
20.06.2017,06:28:02,$CRX:high_band_max=863MHz
20.06.2017,06:28:02,$CRX:Idle=0x
20.06.2017,06:28:02,$CRX:ChargePump=On
20.06.2017,06:28:02,$HST:CD1316LV/IV detected
20.06.2017,06:28:02,$CRX:Debug=Off
20.06.2017,06:28:02,$CRX:Trigger=Extern
20.06.2017,06:28:02,$CRX:FPUcodex=2
20.06.2017,06:28:02,$CRX:GS =61764
20.06.2017,06:28:02,$CRX:GA =624
20.06.2017,06:28:02,$CRX:Delay=0msec
20.06.2017,06:28:02,$CRX:Frequency=45.0MHz
20.06.2017,06:28:02,$HST:Receiver connected
20.06.2017,06:28:02,$CRX:Sweeplength=200
20.06.2017,06:28:02,$CRX:low_band_max=171MHz
20.06.2017,06:28:02,$CRX:mid_band_max=450MHz
20.06.2017,06:28:02,$CRX:high_band_max=863MHz
20.06.2017,06:28:02,$CRX:Idle=0x
20.06.2017,06:28:03,$HST:Switched to manual
20.06.2017,06:28:05,$HST:Param. RCU due to START
20.06.2017,06:28:05,$HST:Actual focuscode 02
20.06.2017,06:28:05,$HST:Enable data transfer
20.06.2017,06:28:05,$HST:Receiver calibration
20.06.2017,06:28:05,$CRX:Started
20.06.2017,06:28:05,$HST:Start new FITS-file
20.06.2017,06:28:06,$HST:Continous measurement
20.06.2017,06:45:04,$HST:XY plot selected
20.06.2017,06:45:06,$HST:XY plot hidden
20.06.2017,06:45:07,$HST:XYZ plot selected
20.06.2017,07:32:22,$HST:XYZ plot hidden
21.06.2017,00:00:00,$HST:Midnight -> memo cleared
21.06.2017,00:00:00,$HST:EOF(logfile)