10.05.2017,13:48:43,$HST:Application just created
10.05.2017,13:48:43,$HST:SW-version 1.18, e-Callisto
10.05.2017,13:48:43,$HST:Configurationfile read
10.05.2017,13:48:43,$HST:Switched to automatic
10.05.2017,13:48:43,$HST:ATmega16 pre-configured
10.05.2017,13:48:43,$HST:Frequencyfile frq01005.cfg
10.05.2017,13:48:43,$HST:Callisto ready now...
10.05.2017,13:48:44,$HST:Measurement idle
10.05.2017,13:48:44,$HST:File scheduler.cfg read
10.05.2017,13:48:44,$HST:Measurement enable
10.05.2017,13:48:44,$CRX:AGC gain = 2.43V
10.05.2017,13:48:44,$CRX:Emitter BF199 = 0.14V
10.05.2017,13:48:44,$CRX:Analog Input = 9.24
10.05.2017,13:48:49,$HST:File frq01005.cfg read
10.05.2017,13:48:49,$HST:No calibration file found
10.05.2017,13:48:49,$HST:Plot buffer erased...
10.05.2017,13:48:49,$HST:Parametrisation RCU
10.05.2017,13:48:50,$CRX:ChargePump=On
10.05.2017,13:48:50,$HST:CD1316LV/IV detected
10.05.2017,13:48:50,$CRX:Debug=Off
10.05.2017,13:48:50,$CRX:Trigger=No
10.05.2017,13:48:50,$CRX:FPUcodex=0
10.05.2017,13:48:50,$CRX:GS =13
10.05.2017,13:48:50,$CRX:GA =253
10.05.2017,13:48:50,$CRX:Delay=0msec
10.05.2017,13:48:50,$CRX:Frequency=0.0MHz
10.05.2017,13:48:50,$HST:Receiver connected
10.05.2017,13:48:50,$CRX:Sweeplength=0
10.05.2017,13:48:50,$CRX:low_band_max=171MHz
10.05.2017,13:48:50,$CRX:mid_band_max=450MHz
10.05.2017,13:48:50,$CRX:high_band_max=863MHz
10.05.2017,13:48:50,$CRX:Idle=0x
10.05.2017,13:48:50,$CRX:ChargePump=On
10.05.2017,13:48:50,$HST:CD1316LV/IV detected
10.05.2017,13:48:50,$CRX:Debug=Off
10.05.2017,13:48:50,$CRX:Trigger=Extern
10.05.2017,13:48:50,$CRX:FPUcodex=0
10.05.2017,13:48:50,$CRX:GS =13
10.05.2017,13:48:50,$CRX:GA =624
10.05.2017,13:48:50,$CRX:Delay=0msec
10.05.2017,13:48:50,$CRX:Frequency=45.0MHz
10.05.2017,13:48:50,$HST:Receiver connected
10.05.2017,13:48:50,$CRX:Sweeplength=200
10.05.2017,13:48:50,$CRX:low_band_max=171MHz
10.05.2017,13:48:50,$CRX:mid_band_max=450MHz
10.05.2017,13:48:50,$CRX:high_band_max=863MHz
10.05.2017,13:48:50,$CRX:Idle=0x
10.05.2017,13:48:56,$HST:XY plot selected
10.05.2017,13:49:02,$HST:Switched to manual
10.05.2017,13:49:04,$HST:Param. RCU due to START
10.05.2017,13:49:04,$HST:Actual focuscode 02
10.05.2017,13:49:05,$HST:Enable data transfer
10.05.2017,13:49:05,$HST:Receiver calibration
10.05.2017,13:49:05,$CRX:Started
10.05.2017,13:49:05,$HST:Start new FITS-file
10.05.2017,13:49:05,$HST:Continous measurement
10.05.2017,13:49:20,$HST:XYZ plot selected
11.05.2017,00:00:00,$HST:Midnight -> memo cleared
11.05.2017,00:00:00,$HST:EOF(logfile)