18.10.2016,00:00:00,$HST:STX(logfile)
18.10.2016,05:59:58,$HST:Measurement stop
18.10.2016,05:59:58,$HST:Measurement wait...
18.10.2016,05:59:59,$HST:Measurement halted
18.10.2016,05:59:59,$HST:Measurement idle
18.10.2016,05:59:59,$CRX:Stopped
18.10.2016,05:59:59,$HST:Measurement enable
18.10.2016,05:59:59,$CRX:AGC gain = 1.59V
18.10.2016,05:59:59,$CRX:Emitter BF199 = 0.13V
18.10.2016,05:59:59,$CRX:Analog Input = 9.24
18.10.2016,06:00:00,$HST:Autostart via scheduler
18.10.2016,06:00:00,$HST:Param. RCU due to START
18.10.2016,06:00:00,$HST:Actual focuscode 59
18.10.2016,06:00:00,$HST:Enable data transfer
18.10.2016,06:00:00,$HST:Continuous measurement
18.10.2016,06:00:00,$CRX:Started
18.10.2016,06:00:00,$HST:Start new FITS-file
18.10.2016,06:00:00,$HST:Continous measurement
18.10.2016,06:15:00,$HST:FITS #1 200rows x 3600cols
18.10.2016,06:30:00,$HST:FITS #2 200rows x 3600cols
18.10.2016,06:45:00,$HST:FITS #3 200rows x 3600cols
18.10.2016,07:00:00,$HST:FITS #4 200rows x 3600cols
18.10.2016,07:15:00,$HST:FITS #5 200rows x 3600cols
18.10.2016,07:21:10,$HST:XYZ plot selected
18.10.2016,07:21:13,$HST:Measurement stop
18.10.2016,07:21:13,$HST:FITS #6 200rows x 1492cols
18.10.2016,07:21:13,$HST:EOT (&) detected
18.10.2016,07:21:13,$HST:Measurement wait...
18.10.2016,07:21:13,$HST:Measurement halted
18.10.2016,07:21:13,$HST:Measurement idle
18.10.2016,07:21:13,$CRX:Stopped
18.10.2016,07:21:13,$HST:Measurement enable
18.10.2016,07:21:13,$CRX:AGC gain = 1.59V
18.10.2016,07:21:13,$CRX:Emitter BF199 = 0.13V
18.10.2016,07:21:13,$CRX:Analog Input = 9.24
18.10.2016,08:20:30,$HST:Manual frequencyfile sel.
18.10.2016,08:20:34,$HST:callisto.cfg watched
18.10.2016,08:20:36,$HST:File c:\users\bleien\myprogs\callisto_argos\callistov117\frq00201.cfg read
18.10.2016,08:20:36,$HST:No calibration file found
18.10.2016,08:20:36,$HST:Plot buffer erased...
18.10.2016,08:20:36,$HST:Parametrisation RCU
18.10.2016,08:20:36,$CRX:ChargePump=On
18.10.2016,08:20:36,$HST:CD1316LV/IV detected
18.10.2016,08:20:36,$CRX:Debug=Off
18.10.2016,08:20:36,$CRX:Trigger=Soft
18.10.2016,08:20:36,$CRX:FPUcodex=59
18.10.2016,08:20:36,$CRX:GS =61750
18.10.2016,08:20:36,$CRX:GA =253
18.10.2016,08:20:36,$CRX:Delay=2msec
18.10.2016,08:20:36,$CRX:Frequency=870.0MHz
18.10.2016,08:20:36,$HST:Receiver connected
18.10.2016,08:20:36,$CRX:Sweeplength=200
18.10.2016,08:20:36,$CRX:low_band_max=171MHz
18.10.2016,08:20:36,$CRX:mid_band_max=450MHz
18.10.2016,08:20:36,$CRX:high_band_max=863MHz
18.10.2016,08:20:36,$CRX:Idle=0x
18.10.2016,08:20:36,$CRX:ChargePump=On
18.10.2016,08:20:36,$HST:CD1316LV/IV detected
18.10.2016,08:20:36,$CRX:Debug=Off
18.10.2016,08:20:36,$CRX:Trigger=Intern
18.10.2016,08:20:36,$CRX:FPUcodex=59
18.10.2016,08:20:36,$CRX:GS =107
18.10.2016,08:20:36,$CRX:GA =253
18.10.2016,08:20:36,$CRX:Delay=2msec
18.10.2016,08:20:36,$CRX:Frequency=45.0MHz
18.10.2016,08:20:36,$HST:Receiver connected
18.10.2016,08:20:36,$CRX:Sweeplength=200
18.10.2016,08:20:36,$CRX:low_band_max=171MHz
18.10.2016,08:20:36,$CRX:mid_band_max=450MHz
18.10.2016,08:20:36,$CRX:high_band_max=863MHz
18.10.2016,08:20:36,$CRX:Idle=0x
18.10.2016,08:20:58,$HST:Yt plot selected
18.10.2016,08:20:59,$HST:XY plot selected
18.10.2016,08:21:00,$HST:Param. RCU due to START
18.10.2016,08:21:00,$HST:Actual focuscode 03
18.10.2016,08:21:00,$HST:Enable data transfer
18.10.2016,08:21:00,$HST:Continuous measurement
18.10.2016,08:21:00,$CRX:Started
18.10.2016,08:21:01,$HST:Start new FITS-file
18.10.2016,08:21:01,$HST:Continous measurement
18.10.2016,09:29:30,$HST:Measurement stop
18.10.2016,09:29:30,$HST:Measurement wait...
18.10.2016,09:29:30,$HST:EOT (&) detected
18.10.2016,09:29:31,$HST:Measurement halted
18.10.2016,09:29:31,$HST:Measurement idle
18.10.2016,09:29:31,$CRX:Stopped
18.10.2016,09:29:31,$HST:Measurement enable
18.10.2016,09:29:31,$CRX:AGC gain = 1.58V
18.10.2016,09:29:31,$CRX:Emitter BF199 = 0.13V
18.10.2016,09:29:31,$CRX:Analog Input = 9.24
18.10.2016,09:29:32,$HST:Start overview...
18.10.2016,09:29:32,$HST:Wait ~45sec please!
18.10.2016,09:30:14,$HST:End spectral overview...
18.10.2016,09:30:14,$HST:Data in log-directory
18.10.2016,09:30:18,$HST:Info panel opened
18.10.2016,09:31:40,$HST:Manual frequencyfile sel.
18.10.2016,09:31:46,$HST:File c:\users\bleien\myprogs\callisto_argos\callistov117\frq00380.cfg read
18.10.2016,09:31:46,$HST:No calibration file found
18.10.2016,09:31:46,$HST:Plot buffer erased...
18.10.2016,09:31:46,$HST:Parametrisation RCU
18.10.2016,09:31:46,$CRX:ChargePump=On
18.10.2016,09:31:46,$HST:CD1316LV/IV detected
18.10.2016,09:31:46,$CRX:Debug=Off
18.10.2016,09:31:46,$CRX:Trigger=Soft
18.10.2016,09:31:46,$CRX:FPUcodex=3
18.10.2016,09:31:46,$CRX:GS =61764
18.10.2016,09:31:46,$CRX:GA =253
18.10.2016,09:31:46,$CRX:Delay=2msec
18.10.2016,09:31:46,$CRX:Frequency=870.0MHz
18.10.2016,09:31:46,$HST:Receiver connected
18.10.2016,09:31:46,$CRX:Sweeplength=13200
18.10.2016,09:31:46,$CRX:low_band_max=171MHz
18.10.2016,09:31:46,$CRX:mid_band_max=450MHz
18.10.2016,09:31:46,$CRX:high_band_max=863MHz
18.10.2016,09:31:46,$CRX:Idle=0x
18.10.2016,09:31:46,$CRX:ChargePump=On
18.10.2016,09:31:46,$HST:CD1316LV/IV detected
18.10.2016,09:31:46,$CRX:Debug=Off
18.10.2016,09:31:46,$CRX:Trigger=Intern
18.10.2016,09:31:46,$CRX:FPUcodex=3
18.10.2016,09:31:46,$CRX:GS =107
18.10.2016,09:31:46,$CRX:GA =253
18.10.2016,09:31:46,$CRX:Delay=2msec
18.10.2016,09:31:46,$CRX:Frequency=45.0MHz
18.10.2016,09:31:46,$HST:Receiver connected
18.10.2016,09:31:46,$CRX:Sweeplength=200
18.10.2016,09:31:46,$CRX:low_band_max=171MHz
18.10.2016,09:31:46,$CRX:mid_band_max=450MHz
18.10.2016,09:31:46,$CRX:high_band_max=863MHz
18.10.2016,09:31:46,$CRX:Idle=0x
18.10.2016,09:31:47,$HST:Param. RCU due to START
18.10.2016,09:31:47,$HST:Actual focuscode 03
18.10.2016,09:31:47,$HST:Enable data transfer
18.10.2016,09:31:47,$HST:Continuous measurement
18.10.2016,09:31:47,$CRX:Started
18.10.2016,09:31:47,$HST:Start new FITS-file
18.10.2016,09:31:47,$HST:Continous measurement
18.10.2016,09:37:34,$HST:Measurement stop
18.10.2016,09:37:34,$HST:Measurement wait...
18.10.2016,09:37:34,$HST:EOT (&) detected
18.10.2016,09:37:34,$HST:Measurement halted
18.10.2016,09:37:35,$HST:Measurement idle
18.10.2016,09:37:35,$CRX:Stopped
18.10.2016,09:37:35,$HST:Measurement enable
18.10.2016,09:37:35,$CRX:AGC gain = 1.59V
18.10.2016,09:37:35,$CRX:Emitter BF199 = 0.13V
18.10.2016,09:37:35,$CRX:Analog Input = 9.24
18.10.2016,09:37:37,$HST:Manual frequencyfile sel.
18.10.2016,09:37:43,$HST:File c:\users\bleien\myprogs\callisto_argos\callistov117\frq00370.cfg read
18.10.2016,09:37:43,$HST:No calibration file found
18.10.2016,09:37:43,$HST:Plot buffer erased...
18.10.2016,09:37:43,$HST:Parametrisation RCU
18.10.2016,09:37:43,$CRX:ChargePump=On
18.10.2016,09:37:43,$HST:CD1316LV/IV detected
18.10.2016,09:37:43,$CRX:Debug=Off
18.10.2016,09:37:43,$CRX:Trigger=Intern
18.10.2016,09:37:43,$CRX:FPUcodex=3
18.10.2016,09:37:43,$CRX:GS =61744
18.10.2016,09:37:43,$CRX:GA =253
18.10.2016,09:37:43,$CRX:Delay=2msec
18.10.2016,09:37:43,$CRX:Frequency=45.0MHz
18.10.2016,09:37:43,$HST:Receiver connected
18.10.2016,09:37:43,$CRX:Sweeplength=200
18.10.2016,09:37:43,$CRX:low_band_max=171MHz
18.10.2016,09:37:43,$CRX:mid_band_max=450MHz
18.10.2016,09:37:43,$CRX:high_band_max=863MHz
18.10.2016,09:37:43,$CRX:Idle=0x
18.10.2016,09:37:43,$CRX:ChargePump=On
18.10.2016,09:37:43,$HST:CD1316LV/IV detected
18.10.2016,09:37:43,$CRX:Debug=Off
18.10.2016,09:37:43,$CRX:Trigger=Intern
18.10.2016,09:37:43,$CRX:FPUcodex=3
18.10.2016,09:37:43,$CRX:GS =107
18.10.2016,09:37:43,$CRX:GA =253
18.10.2016,09:37:43,$CRX:Delay=2msec
18.10.2016,09:37:43,$CRX:Frequency=45.0MHz
18.10.2016,09:37:43,$HST:Receiver connected
18.10.2016,09:37:43,$CRX:Sweeplength=200
18.10.2016,09:37:43,$CRX:low_band_max=171MHz
18.10.2016,09:37:43,$CRX:mid_band_max=450MHz
18.10.2016,09:37:43,$CRX:high_band_max=863MHz
18.10.2016,09:37:43,$CRX:Idle=0x
18.10.2016,09:37:49,$HST:Param. RCU due to START
18.10.2016,09:37:49,$HST:Actual focuscode 03
18.10.2016,09:37:49,$HST:Enable data transfer
18.10.2016,09:37:49,$HST:Continuous measurement
18.10.2016,09:37:49,$CRX:Started
18.10.2016,09:37:50,$HST:Start new FITS-file
18.10.2016,09:37:50,$HST:Continous measurement
18.10.2016,09:39:44,$HST:callisto.cfg watched
18.10.2016,09:49:20,$HST:Info panel opened
18.10.2016,09:52:50,$HST:FITS #7 200rows x 3600cols
18.10.2016,10:07:50,$HST:FITS #8 200rows x 3600cols
18.10.2016,10:22:50,$HST:FITS #9 200rows x 3600cols
18.10.2016,10:37:50,$HST:FITS #10 200rows x 3600cols
18.10.2016,10:52:49,$HST:FITS #11 200rows x 3600cols
18.10.2016,10:59:58,$HST:Measurement stop
18.10.2016,10:59:58,$HST:FITS #12 200rows x 1713cols
18.10.2016,10:59:58,$HST:Measurement wait...
18.10.2016,10:59:58,$HST:EOT (&) detected
18.10.2016,10:59:58,$HST:Measurement halted
18.10.2016,10:59:58,$HST:Measurement stop
18.10.2016,10:59:58,$CRX:Stopped
18.10.2016,10:59:58,$HST:Measurement wait...
18.10.2016,10:59:59,$HST:Measurement halted
18.10.2016,10:59:59,$HST:Measurement idle
18.10.2016,10:59:59,$CRX:Stopped
18.10.2016,10:59:59,$HST:Measurement enable
18.10.2016,10:59:59,$CRX:AGC gain = 1.59V
18.10.2016,10:59:59,$CRX:Emitter BF199 = 0.13V
18.10.2016,10:59:59,$CRX:Analog Input = 9.24
18.10.2016,11:00:00,$HST:Autostart via scheduler
18.10.2016,11:00:00,$HST:Param. RCU due to START
18.10.2016,11:00:00,$HST:Actual focuscode 59
18.10.2016,11:00:00,$HST:Enable data transfer
18.10.2016,11:00:00,$HST:Continuous measurement
18.10.2016,11:00:00,$CRX:Started
18.10.2016,11:00:00,$HST:Start new FITS-file
18.10.2016,11:00:00,$HST:Continous measurement
18.10.2016,11:15:00,$HST:FITS #13 200rows x 3600cols
18.10.2016,11:30:00,$HST:FITS #14 200rows x 3600cols
18.10.2016,11:45:00,$HST:FITS #15 200rows x 3600cols
18.10.2016,12:00:00,$HST:FITS #16 200rows x 3600cols
18.10.2016,12:15:00,$HST:FITS #17 200rows x 3600cols
18.10.2016,12:30:00,$HST:FITS #18 200rows x 3600cols
18.10.2016,12:31:57,$HST:Measurement stop
18.10.2016,12:31:57,$HST:FITS #19 200rows x 469cols
18.10.2016,12:31:57,$HST:Measurement wait...
18.10.2016,12:31:57,$HST:EOT (&) detected
18.10.2016,12:31:58,$HST:Measurement halted
18.10.2016,12:31:58,$HST:Measurement idle
18.10.2016,12:31:58,$CRX:Stopped
18.10.2016,12:31:58,$HST:Measurement enable
18.10.2016,12:31:58,$CRX:AGC gain = 1.59V
18.10.2016,12:31:58,$CRX:Emitter BF199 = 0.13V
18.10.2016,12:31:58,$CRX:Analog Input = 9.24
18.10.2016,12:32:00,$HST:Manual frequencyfile sel.
18.10.2016,12:32:02,$HST:callisto.cfg watched
18.10.2016,12:32:06,$HST:File c:\users\bleien\myprogs\callisto_argos\callistov117\frq00350.cfg read
18.10.2016,12:32:06,$HST:No calibration file found
18.10.2016,12:32:06,$HST:Plot buffer erased...
18.10.2016,12:32:06,$HST:Parametrisation RCU
18.10.2016,12:32:06,$CRX:ChargePump=On
18.10.2016,12:32:06,$HST:CD1316LV/IV detected
18.10.2016,12:32:06,$CRX:Debug=Off
18.10.2016,12:32:06,$CRX:Trigger=Intern
18.10.2016,12:32:06,$CRX:FPUcodex=59
18.10.2016,12:32:06,$CRX:GS =61763
18.10.2016,12:32:06,$CRX:GA =253
18.10.2016,12:32:06,$CRX:Delay=2msec
18.10.2016,12:32:06,$CRX:Frequency=45.0MHz
18.10.2016,12:32:06,$HST:Receiver connected
18.10.2016,12:32:06,$CRX:Sweeplength=200
18.10.2016,12:32:06,$CRX:low_band_max=171MHz
18.10.2016,12:32:06,$CRX:mid_band_max=450MHz
18.10.2016,12:32:06,$CRX:high_band_max=863MHz
18.10.2016,12:32:06,$CRX:Idle=0x
18.10.2016,12:32:06,$CRX:ChargePump=On
18.10.2016,12:32:06,$HST:CD1316LV/IV detected
18.10.2016,12:32:06,$CRX:Debug=Off
18.10.2016,12:32:06,$CRX:Trigger=Intern
18.10.2016,12:32:06,$CRX:FPUcodex=59
18.10.2016,12:32:06,$CRX:GS =107
18.10.2016,12:32:06,$CRX:GA =253
18.10.2016,12:32:06,$CRX:Delay=2msec
18.10.2016,12:32:06,$CRX:Frequency=45.0MHz
18.10.2016,12:32:06,$HST:Receiver connected
18.10.2016,12:32:06,$CRX:Sweeplength=200
18.10.2016,12:32:06,$CRX:low_band_max=171MHz
18.10.2016,12:32:06,$CRX:mid_band_max=450MHz
18.10.2016,12:32:06,$CRX:high_band_max=863MHz
18.10.2016,12:32:06,$CRX:Idle=0x
18.10.2016,12:32:19,$HST:Param. RCU due to START
18.10.2016,12:32:19,$HST:Actual focuscode 03
18.10.2016,12:32:19,$HST:Enable data transfer
18.10.2016,12:32:19,$HST:Continuous measurement
18.10.2016,12:32:19,$CRX:Started
18.10.2016,12:32:19,$HST:Start new FITS-file
18.10.2016,12:32:19,$HST:Continous measurement
18.10.2016,12:43:55,$HST:Measurement stop
18.10.2016,12:43:55,$HST:FITS #20 200rows x 2786cols
18.10.2016,12:43:56,$HST:Measurement wait...
18.10.2016,12:43:56,$HST:EOT (&) detected
18.10.2016,12:43:56,$HST:Measurement halted
18.10.2016,12:43:56,$HST:Measurement idle
18.10.2016,12:43:56,$CRX:Stopped
18.10.2016,12:43:56,$HST:Measurement enable
18.10.2016,12:43:56,$CRX:AGC gain = 1.59V
18.10.2016,12:43:56,$CRX:Emitter BF199 = 0.13V
18.10.2016,12:43:56,$CRX:Analog Input = 9.24
18.10.2016,12:43:58,$HST:Manual frequencyfile sel.
18.10.2016,12:44:04,$HST:File c:\users\bleien\myprogs\callisto_argos\callistov117\frq00350.cfg read
18.10.2016,12:44:04,$HST:No calibration file found
18.10.2016,12:44:04,$HST:Plot buffer erased...
18.10.2016,12:44:04,$HST:Parametrisation RCU
18.10.2016,12:44:04,$CRX:ChargePump=On
18.10.2016,12:44:04,$HST:CD1316LV/IV detected
18.10.2016,12:44:04,$CRX:Debug=Off
18.10.2016,12:44:04,$CRX:Trigger=Intern
18.10.2016,12:44:04,$CRX:FPUcodex=3
18.10.2016,12:44:04,$CRX:GS =61763
18.10.2016,12:44:04,$CRX:GA =253
18.10.2016,12:44:04,$CRX:Delay=2msec
18.10.2016,12:44:04,$CRX:Frequency=45.0MHz
18.10.2016,12:44:04,$HST:Receiver connected
18.10.2016,12:44:04,$CRX:Sweeplength=200
18.10.2016,12:44:04,$CRX:low_band_max=171MHz
18.10.2016,12:44:04,$CRX:mid_band_max=450MHz
18.10.2016,12:44:04,$CRX:high_band_max=863MHz
18.10.2016,12:44:04,$CRX:Idle=0x
18.10.2016,12:44:04,$CRX:ChargePump=On
18.10.2016,12:44:04,$HST:CD1316LV/IV detected
18.10.2016,12:44:04,$CRX:Debug=Off
18.10.2016,12:44:04,$CRX:Trigger=Intern
18.10.2016,12:44:04,$CRX:FPUcodex=3
18.10.2016,12:44:04,$CRX:GS =107
18.10.2016,12:44:04,$CRX:GA =253
18.10.2016,12:44:04,$CRX:Delay=2msec
18.10.2016,12:44:04,$CRX:Frequency=45.0MHz
18.10.2016,12:44:04,$HST:Receiver connected
18.10.2016,12:44:04,$CRX:Sweeplength=200
18.10.2016,12:44:04,$CRX:low_band_max=171MHz
18.10.2016,12:44:04,$CRX:mid_band_max=450MHz
18.10.2016,12:44:04,$CRX:high_band_max=863MHz
18.10.2016,12:44:04,$CRX:Idle=0x
18.10.2016,12:44:05,$HST:Param. RCU due to START
18.10.2016,12:44:05,$HST:Actual focuscode 03
18.10.2016,12:44:05,$HST:Enable data transfer
18.10.2016,12:44:05,$HST:Continuous measurement
18.10.2016,12:44:05,$CRX:Started
18.10.2016,12:44:05,$HST:Start new FITS-file
18.10.2016,12:44:05,$HST:Continous measurement
18.10.2016,12:44:08,$HST:scheduler.cfg watched
18.10.2016,12:44:58,$HST:Measurement stop
18.10.2016,12:44:58,$HST:FITS #21 200rows x 211cols
18.10.2016,12:44:58,$HST:EOT (&) detected
18.10.2016,12:44:58,$HST:Measurement wait...
18.10.2016,12:44:58,$HST:Measurement halted
18.10.2016,12:44:58,$HST:Measurement stop
18.10.2016,12:44:58,$CRX:Stopped
18.10.2016,12:44:58,$HST:Measurement wait...
18.10.2016,12:44:59,$HST:Measurement halted
18.10.2016,12:44:59,$HST:Measurement idle
18.10.2016,12:44:59,$CRX:Stopped
18.10.2016,12:44:59,$HST:Measurement enable
18.10.2016,12:44:59,$CRX:AGC gain = 1.59V
18.10.2016,12:44:59,$CRX:Emitter BF199 = 0.13V
18.10.2016,12:44:59,$CRX:Analog Input = 9.24
18.10.2016,12:45:00,$HST:Autostart via scheduler
18.10.2016,12:45:00,$HST:Param. RCU due to START
18.10.2016,12:45:00,$HST:Actual focuscode 59
18.10.2016,12:45:00,$HST:Enable data transfer
18.10.2016,12:45:00,$HST:Continuous measurement
18.10.2016,12:45:00,$CRX:Started
18.10.2016,12:45:00,$HST:Start new FITS-file
18.10.2016,12:45:00,$HST:Continous measurement
18.10.2016,13:00:00,$HST:FITS #22 200rows x 3600cols
18.10.2016,13:15:00,$HST:FITS #23 200rows x 3600cols
18.10.2016,13:30:00,$HST:FITS #24 200rows x 3600cols
18.10.2016,13:45:00,$HST:FITS #25 200rows x 3600cols
18.10.2016,14:00:00,$HST:FITS #26 200rows x 3600cols
18.10.2016,14:15:00,$HST:FITS #27 200rows x 3600cols
18.10.2016,14:30:00,$HST:FITS #28 200rows x 3600cols
18.10.2016,14:45:00,$HST:FITS #29 200rows x 3600cols
18.10.2016,15:00:00,$HST:FITS #30 200rows x 3600cols
18.10.2016,15:15:00,$HST:FITS #31 200rows x 3600cols
18.10.2016,15:30:00,$HST:FITS #32 200rows x 3600cols
18.10.2016,15:45:00,$HST:FITS #33 200rows x 3600cols
18.10.2016,16:00:00,$HST:FITS #34 200rows x 3600cols
18.10.2016,16:14:58,$HST:Measurement stop
18.10.2016,16:14:58,$HST:FITS #35 200rows x 3591cols
18.10.2016,16:14:58,$HST:Measurement wait...
18.10.2016,16:14:58,$HST:EOT (&) detected
18.10.2016,16:14:58,$HST:Measurement halted
18.10.2016,16:14:58,$HST:Measurement stop
18.10.2016,16:14:58,$CRX:Stopped
18.10.2016,16:14:58,$HST:Measurement wait...
18.10.2016,16:14:59,$HST:Measurement halted
18.10.2016,16:14:59,$HST:Measurement idle
18.10.2016,16:14:59,$CRX:Stopped
18.10.2016,16:14:59,$HST:Measurement enable
18.10.2016,16:14:59,$CRX:AGC gain = 1.59V
18.10.2016,16:14:59,$CRX:Emitter BF199 = 0.13V
18.10.2016,16:14:59,$CRX:Analog Input = 9.24
18.10.2016,16:59:58,$HST:Measurement stop
18.10.2016,16:59:58,$HST:Measurement wait...
18.10.2016,16:59:59,$HST:Measurement halted
18.10.2016,16:59:59,$HST:Measurement idle
18.10.2016,16:59:59,$CRX:Stopped
18.10.2016,16:59:59,$HST:Measurement enable
18.10.2016,16:59:59,$CRX:AGC gain = 1.59V
18.10.2016,16:59:59,$CRX:Emitter BF199 = 0.13V
18.10.2016,16:59:59,$CRX:Analog Input = 9.24
18.10.2016,17:00:00,$HST:Radio monitoring
18.10.2016,17:00:00,$HST:Start overview...
18.10.2016,17:00:00,$HST:Wait ~45sec please!
18.10.2016,17:00:41,$HST:End spectral overview...
18.10.2016,17:00:41,$HST:Data in log-directory
19.10.2016,00:00:00,$HST:Midnight -> memo cleared
19.10.2016,00:00:00,$HST:EOF(logfile)