12.10.2016,08:04:15,$HST:Application just created
12.10.2016,08:04:15,$HST:SW-version 1.18, e-Callisto
12.10.2016,08:04:15,$HST:Configurationfile read
12.10.2016,08:04:15,$HST:Switched to automatic
12.10.2016,08:04:15,$HST:ATmega16 pre-configured
12.10.2016,08:04:15,$HST:Frequencyfile frq01005.cfg
12.10.2016,08:04:15,$HST:Callisto ready now...
12.10.2016,08:04:16,$HST:Measurement idle
12.10.2016,08:04:16,$HST:File scheduler.cfg read
12.10.2016,08:04:16,$HST:Measurement enable
12.10.2016,08:04:16,$CRX:AGC gain = 2.43V
12.10.2016,08:04:16,$CRX:Emitter BF199 = 0.14V
12.10.2016,08:04:16,$CRX:Analog Input = 9.24
12.10.2016,08:04:21,$HST:File frq01005.cfg read
12.10.2016,08:04:21,$HST:No calibration file found
12.10.2016,08:04:21,$HST:Plot buffer erased...
12.10.2016,08:04:21,$HST:Parametrisation RCU
12.10.2016,08:04:22,$CRX:ChargePump=On
12.10.2016,08:04:22,$HST:CD1316LV/IV detected
12.10.2016,08:04:22,$CRX:Debug=Off
12.10.2016,08:04:22,$CRX:Trigger=Extern
12.10.2016,08:04:22,$CRX:FPUcodex=2
12.10.2016,08:04:22,$CRX:GS =3378
12.10.2016,08:04:22,$CRX:GA =624
12.10.2016,08:04:22,$CRX:Delay=0msec
12.10.2016,08:04:22,$CRX:Frequency=45.0MHz
12.10.2016,08:04:22,$HST:Receiver connected
12.10.2016,08:04:22,$CRX:Sweeplength=200
12.10.2016,08:04:22,$CRX:low_band_max=171MHz
12.10.2016,08:04:22,$CRX:mid_band_max=450MHz
12.10.2016,08:04:22,$CRX:high_band_max=863MHz
12.10.2016,08:04:22,$CRX:Idle=0x
12.10.2016,08:04:22,$CRX:ChargePump=On
12.10.2016,08:04:22,$HST:CD1316LV/IV detected
12.10.2016,08:04:22,$CRX:Debug=Off
12.10.2016,08:04:22,$CRX:Trigger=Extern
12.10.2016,08:04:22,$CRX:FPUcodex=2
12.10.2016,08:04:22,$CRX:GS =3378
12.10.2016,08:04:22,$CRX:GA =624
12.10.2016,08:04:22,$CRX:Delay=0msec
12.10.2016,08:04:22,$CRX:Frequency=45.0MHz
12.10.2016,08:04:22,$HST:Receiver connected
12.10.2016,08:04:22,$CRX:Sweeplength=200
12.10.2016,08:04:22,$CRX:low_band_max=171MHz
12.10.2016,08:04:22,$CRX:mid_band_max=450MHz
12.10.2016,08:04:22,$CRX:high_band_max=863MHz
12.10.2016,08:04:22,$CRX:Idle=0x
12.10.2016,08:04:27,$HST:File FRQ01005.CFG read
12.10.2016,08:04:27,$HST:No calibration file found
12.10.2016,08:04:27,$HST:Plot buffer erased...
12.10.2016,08:04:27,$HST:Parametrisation RCU
12.10.2016,08:04:27,$CRX:ChargePump=On
12.10.2016,08:04:27,$HST:CD1316LV/IV detected
12.10.2016,08:04:27,$CRX:Debug=Off
12.10.2016,08:04:27,$CRX:Trigger=Extern
12.10.2016,08:04:27,$CRX:FPUcodex=2
12.10.2016,08:04:27,$CRX:GS =3378
12.10.2016,08:04:27,$CRX:GA =624
12.10.2016,08:04:27,$CRX:Delay=0msec
12.10.2016,08:04:27,$CRX:Frequency=45.0MHz
12.10.2016,08:04:27,$HST:Receiver connected
12.10.2016,08:04:27,$CRX:Sweeplength=200
12.10.2016,08:04:27,$CRX:low_band_max=171MHz
12.10.2016,08:04:27,$CRX:mid_band_max=450MHz
12.10.2016,08:04:27,$CRX:high_band_max=863MHz
12.10.2016,08:04:27,$CRX:Idle=0x
12.10.2016,08:04:27,$CRX:ChargePump=On
12.10.2016,08:04:27,$HST:CD1316LV/IV detected
12.10.2016,08:04:27,$CRX:Debug=Off
12.10.2016,08:04:27,$CRX:Trigger=Extern
12.10.2016,08:04:27,$CRX:FPUcodex=2
12.10.2016,08:04:27,$CRX:GS =3378
12.10.2016,08:04:27,$CRX:GA =624
12.10.2016,08:04:27,$CRX:Delay=0msec
12.10.2016,08:04:27,$CRX:Frequency=45.0MHz
12.10.2016,08:04:27,$HST:Receiver connected
12.10.2016,08:04:27,$CRX:Sweeplength=200
12.10.2016,08:04:27,$CRX:low_band_max=171MHz
12.10.2016,08:04:27,$CRX:mid_band_max=450MHz
12.10.2016,08:04:27,$CRX:high_band_max=863MHz
12.10.2016,08:04:27,$CRX:Idle=0x
12.10.2016,08:04:34,$HST:Param. RCU due to START
12.10.2016,08:04:34,$HST:Actual focuscode 02
12.10.2016,08:04:34,$HST:Enable data transfer
12.10.2016,08:04:34,$HST:Receiver calibration
12.10.2016,08:04:34,$CRX:Started
12.10.2016,08:04:34,$HST:Start new FITS-file
12.10.2016,08:04:35,$HST:Continous measurement
12.10.2016,08:04:37,$HST:Switched to manual
12.10.2016,08:04:54,$HST:XYZ plot selected
12.10.2016,08:31:32,$HST:Yt plot selected
12.10.2016,08:31:45,$HST:XYZ plot selected
13.10.2016,00:00:00,$HST:Midnight -> memo cleared
13.10.2016,00:00:00,$HST:EOF(logfile)