12.10.2016,08:11:39,$HST:Application just created
12.10.2016,08:11:39,$HST:SW-version 1.16, e-Callisto
12.10.2016,08:11:39,$HST:Configurationfile read
12.10.2016,08:11:39,$HST:Switched to automatic
12.10.2016,08:11:39,$HST:ATmega16 pre-configured
12.10.2016,08:11:39,$HST:Frequencyfile frq00255.cfg
12.10.2016,08:11:39,$HST:Callisto ready now...
12.10.2016,08:11:40,$HST:Measurement idle
12.10.2016,08:11:40,$HST:File scheduler.cfg read
12.10.2016,08:11:40,$HST:Measurement enable
12.10.2016,08:11:40,$CRX:AGC gain = 0.89V
12.10.2016,08:11:40,$CRX:Emitter BF199 = 0.12V
12.10.2016,08:11:40,$CRX:Analog Input = 9.24
12.10.2016,08:11:46,$HST:File frq00255.cfg read
12.10.2016,08:11:46,$HST:No calibration file found
12.10.2016,08:11:46,$HST:Plot buffer erased...
12.10.2016,08:11:46,$HST:Parametrisation RCU
12.10.2016,08:11:46,$CRX:ChargePump=On
12.10.2016,08:11:46,$HST:CD1316LV/IV detected
12.10.2016,08:11:46,$CRX:Debug=Off
12.10.2016,08:11:46,$CRX:Trigger=Soft
12.10.2016,08:11:46,$CRX:FPUcodex=58
12.10.2016,08:11:46,$CRX:GS =3385
12.10.2016,08:11:46,$CRX:GA =253
12.10.2016,08:11:46,$CRX:Delay=2msec
12.10.2016,08:11:46,$CRX:Frequency=870.0MHz
12.10.2016,08:11:46,$HST:Receiver connected
12.10.2016,08:11:46,$CRX:Sweeplength=200
12.10.2016,08:11:46,$CRX:low_band_max=171MHz
12.10.2016,08:11:46,$CRX:mid_band_max=450MHz
12.10.2016,08:11:46,$CRX:high_band_max=863MHz
12.10.2016,08:11:46,$CRX:Idle=0x
12.10.2016,08:11:46,$CRX:ChargePump=On
12.10.2016,08:11:46,$HST:CD1316LV/IV detected
12.10.2016,08:11:46,$CRX:Debug=Off
12.10.2016,08:11:46,$CRX:Trigger=Extern
12.10.2016,08:11:46,$CRX:FPUcodex=58
12.10.2016,08:11:46,$CRX:GS =3385
12.10.2016,08:11:46,$CRX:GA =624
12.10.2016,08:11:46,$CRX:Delay=2msec
12.10.2016,08:11:46,$CRX:Frequency=45.0MHz
12.10.2016,08:11:46,$HST:Receiver connected
12.10.2016,08:11:46,$CRX:Sweeplength=200
12.10.2016,08:11:46,$CRX:low_band_max=171MHz
12.10.2016,08:11:46,$CRX:mid_band_max=450MHz
12.10.2016,08:11:46,$CRX:high_band_max=863MHz
12.10.2016,08:11:46,$CRX:Idle=0x
12.10.2016,08:11:50,$HST:Param. RCU due to START
12.10.2016,08:11:50,$HST:Actual focuscode 02
12.10.2016,08:11:50,$HST:Enable data transfer
12.10.2016,08:11:50,$HST:Continuous measurement
12.10.2016,08:11:50,$CRX:Started
12.10.2016,08:11:50,$HST:Start new FITS-file
12.10.2016,08:11:50,$HST:Continous measurement
12.10.2016,08:11:53,$HST:XYZ plot selected
12.10.2016,08:12:16,$HST:scheduler.cfg watched
12.10.2016,08:12:39,$HST:XYZ plot hidden
12.10.2016,08:14:58,$HST:Measurement stop
12.10.2016,08:14:58,$HST:FITS #1 200rows x 750cols
12.10.2016,08:14:58,$HST:Measurement wait...
12.10.2016,08:14:58,$HST:EOT (&) detected
12.10.2016,08:14:58,$HST:Measurement halted
12.10.2016,08:14:58,$HST:Measurement stop
12.10.2016,08:14:58,$CRX:Stopped
12.10.2016,08:14:58,$HST:Measurement wait...
12.10.2016,08:14:59,$HST:Measurement halted
12.10.2016,08:14:59,$HST:Measurement idle
12.10.2016,08:14:59,$CRX:Stopped
12.10.2016,08:15:00,$HST:Autostart via scheduler
12.10.2016,08:15:00,$HST:Param. RCU due to START
12.10.2016,08:15:00,$HST:Actual focuscode 58
12.10.2016,08:15:00,$CRX:AGC gain = 0.89V
12.10.2016,08:15:00,$CRX:Emitter BF199 = 0.12V
12.10.2016,08:15:00,$CRX:Analog Input = 9.24
12.10.2016,08:15:00,$HST:Enable data transfer
12.10.2016,08:15:00,$HST:Continuous measurement
12.10.2016,08:15:00,$CRX:Started
12.10.2016,08:15:00,$HST:Start new FITS-file
12.10.2016,08:15:00,$HST:Continous measurement
12.10.2016,08:30:00,$HST:FITS #2 200rows x 3600cols
12.10.2016,08:45:00,$HST:FITS #3 200rows x 3600cols
12.10.2016,09:00:00,$HST:FITS #4 200rows x 3600cols
12.10.2016,09:15:00,$HST:FITS #5 200rows x 3600cols
12.10.2016,09:30:00,$HST:FITS #6 200rows x 3600cols
12.10.2016,09:45:00,$HST:FITS #7 200rows x 3600cols
12.10.2016,10:00:00,$HST:FITS #8 200rows x 3600cols
12.10.2016,10:15:00,$HST:FITS #9 200rows x 3600cols
12.10.2016,10:30:00,$HST:FITS #10 200rows x 3600cols
12.10.2016,10:45:00,$HST:FITS #11 200rows x 3600cols
12.10.2016,10:59:58,$HST:Measurement stop
12.10.2016,10:59:58,$HST:FITS #12 200rows x 3591cols
12.10.2016,10:59:58,$HST:Measurement wait...
12.10.2016,10:59:58,$HST:EOT (&) detected
12.10.2016,10:59:58,$HST:Measurement halted
12.10.2016,10:59:58,$HST:Measurement stop
12.10.2016,10:59:58,$CRX:Stopped
12.10.2016,10:59:58,$HST:Measurement wait...
12.10.2016,10:59:59,$HST:Measurement halted
12.10.2016,10:59:59,$HST:Measurement idle
12.10.2016,10:59:59,$CRX:Stopped
12.10.2016,11:00:00,$HST:Measurement enable
12.10.2016,11:00:00,$CRX:AGC gain = 0.89V
12.10.2016,11:00:00,$CRX:Emitter BF199 = 0.13V
12.10.2016,11:00:00,$CRX:Analog Input = 9.24
12.10.2016,11:00:00,$HST:Autostart via scheduler
12.10.2016,11:00:00,$HST:Param. RCU due to START
12.10.2016,11:00:00,$HST:Actual focuscode 58
12.10.2016,11:00:00,$HST:Enable data transfer
12.10.2016,11:00:00,$HST:Continuous measurement
12.10.2016,11:00:00,$CRX:Started
12.10.2016,11:00:00,$HST:Start new FITS-file
12.10.2016,11:00:00,$HST:Continous measurement
12.10.2016,11:15:00,$HST:FITS #13 200rows x 3600cols
12.10.2016,11:30:00,$HST:FITS #14 200rows x 3600cols
12.10.2016,11:45:00,$HST:FITS #15 200rows x 3600cols
12.10.2016,12:00:00,$HST:FITS #16 200rows x 3600cols
12.10.2016,12:15:00,$HST:FITS #17 200rows x 3600cols
12.10.2016,12:30:00,$HST:FITS #18 200rows x 3600cols
12.10.2016,12:45:00,$HST:FITS #19 200rows x 3600cols
12.10.2016,13:00:00,$HST:FITS #20 200rows x 3600cols
12.10.2016,13:15:00,$HST:FITS #21 200rows x 3600cols
12.10.2016,13:30:00,$HST:FITS #22 200rows x 3600cols
12.10.2016,13:45:00,$HST:FITS #23 200rows x 3600cols
12.10.2016,14:00:00,$HST:FITS #24 200rows x 3600cols
12.10.2016,14:15:00,$HST:FITS #25 200rows x 3600cols
12.10.2016,14:30:00,$HST:FITS #26 200rows x 3600cols
12.10.2016,14:45:00,$HST:FITS #27 200rows x 3600cols
12.10.2016,15:00:00,$HST:FITS #28 200rows x 3600cols
12.10.2016,15:15:00,$HST:FITS #29 200rows x 3600cols
12.10.2016,15:30:00,$HST:FITS #30 200rows x 3600cols
12.10.2016,15:45:00,$HST:FITS #31 200rows x 3600cols
12.10.2016,16:00:00,$HST:FITS #32 200rows x 3600cols
12.10.2016,16:15:00,$HST:FITS #33 200rows x 3600cols
12.10.2016,16:29:58,$HST:Measurement stop
12.10.2016,16:29:58,$HST:FITS #34 200rows x 3591cols
12.10.2016,16:29:58,$HST:Measurement wait...
12.10.2016,16:29:58,$HST:EOT (&) detected
12.10.2016,16:29:58,$HST:Measurement halted
12.10.2016,16:29:58,$HST:Measurement stop
12.10.2016,16:29:58,$CRX:Stopped
12.10.2016,16:29:59,$HST:Measurement wait...
12.10.2016,16:29:59,$HST:Measurement halted
12.10.2016,16:30:00,$HST:Measurement idle
12.10.2016,16:30:00,$CRX:Stopped
12.10.2016,16:30:00,$HST:Measurement enable
12.10.2016,16:30:00,$CRX:AGC gain = 0.89V
12.10.2016,16:30:00,$CRX:Emitter BF199 = 0.13V
12.10.2016,16:30:00,$CRX:Analog Input = 9.24
12.10.2016,16:59:58,$HST:Measurement stop
12.10.2016,16:59:58,$HST:Measurement wait...
12.10.2016,16:59:59,$HST:Measurement halted
12.10.2016,16:59:59,$HST:Measurement idle
12.10.2016,16:59:59,$CRX:Stopped
12.10.2016,16:59:59,$HST:Measurement enable
12.10.2016,16:59:59,$CRX:AGC gain = 0.89V
12.10.2016,16:59:59,$CRX:Emitter BF199 = 0.13V
12.10.2016,16:59:59,$CRX:Analog Input = 9.24
12.10.2016,17:00:00,$HST:Radio monitoring
12.10.2016,17:00:00,$HST:Start overview...
12.10.2016,17:00:00,$HST:Wait ~45sec please!
12.10.2016,17:00:01,$HST:No more entries in scheduler.
12.10.2016,17:00:41,$HST:End spectral overview...
12.10.2016,17:00:41,$HST:Data in log-directory
13.10.2016,00:00:00,$HST:Midnight -> memo cleared
13.10.2016,00:00:00,$HST:EOF(logfile)