27.05.2016,18:41:27,$HST:Application just created
27.05.2016,18:41:27,$HST:SW-version 1.16, e-Callisto
27.05.2016,18:41:27,$HST:Configurationfile read
27.05.2016,18:41:27,$HST:Switched to automatic
27.05.2016,18:41:27,$HST:ATmega16 pre-configured
27.05.2016,18:41:27,$HST:Frequencyfile frq00255.cfg
27.05.2016,18:41:27,$HST:Callisto ready now...
27.05.2016,18:41:28,$HST:Measurement idle
27.05.2016,18:41:28,$HST:File scheduler.cfg read
27.05.2016,18:41:28,$HST:Measurement enable
27.05.2016,18:41:28,$CRX:AGC gain = 0.89V
27.05.2016,18:41:28,$CRX:Emitter BF199 = 0.13V
27.05.2016,18:41:28,$CRX:Analog Input = 9.24
27.05.2016,18:41:31,$HST:XY plot selected
27.05.2016,18:41:34,$HST:File frq00255.cfg read
27.05.2016,18:41:34,$HST:No calibration file found
27.05.2016,18:41:34,$HST:Plot buffer erased...
27.05.2016,18:41:34,$HST:Parametrisation RCU
27.05.2016,18:41:34,$CRX:ChargePump=On
27.05.2016,18:41:34,$HST:CD1316LV/IV detected
27.05.2016,18:41:34,$CRX:Debug=Off
27.05.2016,18:41:34,$CRX:Trigger=Soft
27.05.2016,18:41:34,$CRX:FPUcodex=58
27.05.2016,18:41:34,$CRX:GS =3382
27.05.2016,18:41:34,$CRX:GA =253
27.05.2016,18:41:34,$CRX:Delay=2msec
27.05.2016,18:41:34,$CRX:Frequency=870.0MHz
27.05.2016,18:41:34,$HST:Receiver connected
27.05.2016,18:41:34,$CRX:Sweeplength=200
27.05.2016,18:41:34,$CRX:low_band_max=171MHz
27.05.2016,18:41:34,$CRX:mid_band_max=450MHz
27.05.2016,18:41:34,$CRX:high_band_max=863MHz
27.05.2016,18:41:34,$CRX:Idle=0x
27.05.2016,18:41:34,$CRX:ChargePump=On
27.05.2016,18:41:34,$HST:CD1316LV/IV detected
27.05.2016,18:41:34,$CRX:Debug=Off
27.05.2016,18:41:34,$CRX:Trigger=Extern
27.05.2016,18:41:34,$CRX:FPUcodex=58
27.05.2016,18:41:34,$CRX:GS =3382
27.05.2016,18:41:34,$CRX:GA =624
27.05.2016,18:41:34,$CRX:Delay=2msec
27.05.2016,18:41:34,$CRX:Frequency=45.0MHz
27.05.2016,18:41:34,$HST:Receiver connected
27.05.2016,18:41:34,$CRX:Sweeplength=200
27.05.2016,18:41:34,$CRX:low_band_max=171MHz
27.05.2016,18:41:34,$CRX:mid_band_max=450MHz
27.05.2016,18:41:34,$CRX:high_band_max=863MHz
27.05.2016,18:41:34,$CRX:Idle=0x
27.05.2016,18:41:40,$HST:Param. RCU due to START
27.05.2016,18:41:40,$HST:Actual focuscode 02
27.05.2016,18:41:41,$HST:Enable data transfer
27.05.2016,18:41:41,$HST:Continuous measurement
27.05.2016,18:41:41,$CRX:Started
27.05.2016,18:41:41,$HST:Start new FITS-file
27.05.2016,18:41:41,$HST:Continous measurement
27.05.2016,18:42:01,$HST:All threads terminated
27.05.2016,18:42:01,$HST:This application closed