21.01.2016,10:33:13,$HST:Application just created
21.01.2016,10:33:13,$HST:SW-version 1.16, e-Callisto
21.01.2016,10:33:13,$HST:Configurationfile read
21.01.2016,10:33:13,$HST:Switched to automatic
21.01.2016,10:33:13,$HST:ATmega16 pre-configured
21.01.2016,10:33:13,$HST:Frequencyfile frq00255.cfg
21.01.2016,10:33:13,$HST:Callisto ready now...
21.01.2016,10:33:13,$HST:Measurement idle
21.01.2016,10:33:13,$HST:File scheduler.cfg read
21.01.2016,10:33:13,$HST:Measurement enable
21.01.2016,10:33:13,$CRX:AGC gain = 1.79V
21.01.2016,10:33:13,$CRX:Emitter BF199 = 0.12V
21.01.2016,10:33:13,$CRX:Analog Input = 9.24
21.01.2016,10:33:19,$HST:File frq00255.cfg read
21.01.2016,10:33:19,$HST:No calibration file found
21.01.2016,10:33:19,$HST:Plot buffer erased...
21.01.2016,10:33:19,$HST:Parametrisation RCU
21.01.2016,10:33:19,$CRX:ChargePump=On
21.01.2016,10:33:19,$HST:CD1316LV/IV detected
21.01.2016,10:33:19,$CRX:Debug=Off
21.01.2016,10:33:19,$CRX:Trigger=Soft
21.01.2016,10:33:19,$CRX:FPUcodex=58
21.01.2016,10:33:19,$CRX:GS =3377
21.01.2016,10:33:19,$CRX:GA =253
21.01.2016,10:33:19,$CRX:Delay=2msec
21.01.2016,10:33:19,$CRX:Frequency=870.0MHz
21.01.2016,10:33:19,$HST:Receiver connected
21.01.2016,10:33:19,$CRX:Sweeplength=200
21.01.2016,10:33:19,$CRX:low_band_max=171MHz
21.01.2016,10:33:19,$CRX:mid_band_max=450MHz
21.01.2016,10:33:19,$CRX:high_band_max=863MHz
21.01.2016,10:33:19,$CRX:Idle=0x
21.01.2016,10:33:19,$CRX:ChargePump=On
21.01.2016,10:33:19,$HST:CD1316LV/IV detected
21.01.2016,10:33:19,$CRX:Debug=Off
21.01.2016,10:33:19,$CRX:Trigger=Extern
21.01.2016,10:33:19,$CRX:FPUcodex=58
21.01.2016,10:33:19,$CRX:GS =3377
21.01.2016,10:33:19,$CRX:GA =624
21.01.2016,10:33:19,$CRX:Delay=2msec
21.01.2016,10:33:19,$CRX:Frequency=45.0MHz
21.01.2016,10:33:19,$HST:Receiver connected
21.01.2016,10:33:19,$CRX:Sweeplength=200
21.01.2016,10:33:19,$CRX:low_band_max=171MHz
21.01.2016,10:33:19,$CRX:mid_band_max=450MHz
21.01.2016,10:33:19,$CRX:high_band_max=863MHz
21.01.2016,10:33:19,$CRX:Idle=0x
21.01.2016,10:33:31,$HST:XY plot selected
21.01.2016,10:33:33,$HST:Param. RCU due to START
21.01.2016,10:33:33,$HST:Actual focuscode 01
21.01.2016,10:33:34,$HST:Enable data transfer
21.01.2016,10:33:34,$HST:Continuous measurement
21.01.2016,10:33:34,$CRX:Started
21.01.2016,10:33:34,$HST:Start new FITS-file
21.01.2016,10:33:34,$HST:Continous measurement
21.01.2016,10:33:44,$HST:XYZ plot selected
21.01.2016,10:48:34,$HST:FITS #1 200rows x 3600cols
21.01.2016,11:03:34,$HST:FITS #2 200rows x 3600cols
21.01.2016,11:18:34,$HST:FITS #3 200rows x 3600cols
21.01.2016,11:29:58,$HST:Measurement stop
21.01.2016,11:29:58,$HST:FITS #4 200rows x 2736cols
21.01.2016,11:29:58,$HST:Measurement wait...
21.01.2016,11:29:58,$HST:EOT (&) detected
21.01.2016,11:29:58,$HST:Measurement halted
21.01.2016,11:29:58,$HST:Measurement stop
21.01.2016,11:29:58,$CRX:Stopped
21.01.2016,11:29:58,$HST:Measurement wait...
21.01.2016,11:29:59,$HST:Measurement halted
21.01.2016,11:29:59,$HST:Measurement idle
21.01.2016,11:29:59,$CRX:Stopped
21.01.2016,11:30:00,$HST:Autostart via scheduler
21.01.2016,11:30:00,$HST:Param. RCU due to START
21.01.2016,11:30:00,$HST:Actual focuscode 58
21.01.2016,11:30:00,$CRX:AGC gain = 1.79V
21.01.2016,11:30:00,$CRX:Emitter BF199 = 0.12V
21.01.2016,11:30:00,$CRX:Analog Input = 9.24
21.01.2016,11:30:00,$HST:Enable data transfer
21.01.2016,11:30:00,$HST:Continuous measurement