23.04.2015,09:00:22,$HST:Application just created
23.04.2015,09:00:22,$HST:SW-version 1.18, e-Callisto
23.04.2015,09:00:22,$HST:Configurationfile read
23.04.2015,09:00:22,$HST:Switched to automatic
23.04.2015,09:00:22,$HST:ATmega16 pre-configured
23.04.2015,09:00:22,$HST:Frequencyfile frq01000.cfg
23.04.2015,09:00:22,$HST:Callisto ready now...
23.04.2015,09:00:23,$HST:Measurement idle
23.04.2015,09:00:23,$HST:File scheduler.cfg read
23.04.2015,09:00:23,$HST:Measurement enable
23.04.2015,09:00:23,$CRX:AGC gain = 1.57V
23.04.2015,09:00:23,$CRX:Emitter BF199 = 0.14V
23.04.2015,09:00:23,$CRX:Analog Input = 9.24
23.04.2015,09:00:29,$HST:File frq01000.cfg read
23.04.2015,09:00:29,$HST:No calibration file found
23.04.2015,09:00:29,$HST:Plot buffer erased...
23.04.2015,09:00:29,$HST:Parametrisation RCU
23.04.2015,09:00:29,$CRX:ChargePump=On
23.04.2015,09:00:29,$HST:CD1316LV/IV detected
23.04.2015,09:00:29,$CRX:Debug=Off
23.04.2015,09:00:29,$CRX:Trigger=Soft
23.04.2015,09:00:29,$CRX:FPUcodex=2
23.04.2015,09:00:29,$CRX:GS =61748
23.04.2015,09:00:29,$CRX:GA =253
23.04.2015,09:00:29,$CRX:Delay=2msec
23.04.2015,09:00:29,$CRX:Frequency=870.0MHz
23.04.2015,09:00:29,$HST:Receiver connected
23.04.2015,09:00:29,$CRX:Sweeplength=13200
23.04.2015,09:00:29,$CRX:low_band_max=171MHz
23.04.2015,09:00:29,$CRX:mid_band_max=450MHz
23.04.2015,09:00:29,$CRX:high_band_max=863MHz
23.04.2015,09:00:29,$CRX:Idle=0x
23.04.2015,09:00:29,$CRX:ChargePump=On
23.04.2015,09:00:29,$HST:CD1316LV/IV detected
23.04.2015,09:00:29,$CRX:Debug=Off
23.04.2015,09:00:29,$CRX:Trigger=Extern
23.04.2015,09:00:29,$CRX:FPUcodex=2
23.04.2015,09:00:29,$CRX:GS =61748
23.04.2015,09:00:29,$CRX:GA =624
23.04.2015,09:00:29,$CRX:Delay=2msec
23.04.2015,09:00:29,$CRX:Frequency=45.0MHz
23.04.2015,09:00:29,$HST:Receiver connected
23.04.2015,09:00:29,$CRX:Sweeplength=200
23.04.2015,09:00:29,$CRX:low_band_max=171MHz
23.04.2015,09:00:29,$CRX:mid_band_max=450MHz
23.04.2015,09:00:29,$CRX:high_band_max=863MHz
23.04.2015,09:00:29,$CRX:Idle=0x
23.04.2015,09:00:35,$HST:File FRQ01000.CFG read
23.04.2015,09:00:35,$HST:No calibration file found
23.04.2015,09:00:35,$HST:Plot buffer erased...
23.04.2015,09:00:35,$HST:Parametrisation RCU
23.04.2015,09:00:35,$CRX:ChargePump=On
23.04.2015,09:00:35,$HST:CD1316LV/IV detected
23.04.2015,09:00:35,$CRX:Debug=Off
23.04.2015,09:00:35,$CRX:Trigger=Extern
23.04.2015,09:00:35,$CRX:FPUcodex=2
23.04.2015,09:00:35,$CRX:GS =61748
23.04.2015,09:00:35,$CRX:GA =624
23.04.2015,09:00:35,$CRX:Delay=2msec
23.04.2015,09:00:35,$CRX:Frequency=45.0MHz
23.04.2015,09:00:35,$HST:Receiver connected
23.04.2015,09:00:35,$CRX:Sweeplength=200
23.04.2015,09:00:35,$CRX:low_band_max=171MHz
23.04.2015,09:00:35,$CRX:mid_band_max=450MHz
23.04.2015,09:00:35,$CRX:high_band_max=863MHz
23.04.2015,09:00:35,$CRX:Idle=0x
23.04.2015,09:00:35,$CRX:ChargePump=On
23.04.2015,09:00:35,$HST:CD1316LV/IV detected
23.04.2015,09:00:35,$CRX:Debug=Off
23.04.2015,09:00:35,$CRX:Trigger=Extern
23.04.2015,09:00:35,$CRX:FPUcodex=2
23.04.2015,09:00:35,$CRX:GS =61748
23.04.2015,09:00:35,$CRX:GA =624
23.04.2015,09:00:35,$CRX:Delay=2msec
23.04.2015,09:00:35,$CRX:Frequency=45.0MHz
23.04.2015,09:00:35,$HST:Receiver connected
23.04.2015,09:00:35,$CRX:Sweeplength=200
23.04.2015,09:00:35,$CRX:low_band_max=171MHz
23.04.2015,09:00:35,$CRX:mid_band_max=450MHz
23.04.2015,09:00:35,$CRX:high_band_max=863MHz
23.04.2015,09:00:35,$CRX:Idle=0x
23.04.2015,09:00:37,$HST:Yt plot selected
23.04.2015,09:00:37,$HST:XY plot selected
23.04.2015,09:00:38,$HST:XYZ plot selected
23.04.2015,09:00:39,$HST:Param. RCU due to START
23.04.2015,09:00:39,$HST:Actual focuscode 02
23.04.2015,09:00:39,$HST:Enable data transfer
23.04.2015,09:00:39,$HST:Receiver calibration
23.04.2015,09:00:39,$CRX:Started
23.04.2015,09:00:39,$HST:Start new FITS-file
23.04.2015,09:00:39,$HST:Continous measurement
23.04.2015,09:00:48,$HST:callisto.cfg watched
23.04.2015,09:15:39,$HST:FITS #1 200rows x 3600cols
23.04.2015,09:30:39,$HST:FITS #2 200rows x 3600cols
23.04.2015,09:45:39,$HST:FITS #3 200rows x 3600cols
23.04.2015,10:00:39,$HST:FITS #4 200rows x 3600cols
23.04.2015,10:15:39,$HST:FITS #5 200rows x 3600cols
23.04.2015,10:30:39,$HST:FITS #6 200rows x 3600cols
23.04.2015,10:45:39,$HST:FITS #7 200rows x 3600cols
23.04.2015,11:00:39,$HST:FITS #8 200rows x 3600cols
23.04.2015,11:14:58,$HST:Measurement stop
23.04.2015,11:14:58,$HST:FITS #9 200rows x 3436cols
23.04.2015,11:14:58,$HST:Measurement wait...
23.04.2015,11:14:58,$HST:EOT (&) detected
23.04.2015,11:14:58,$HST:Measurement halted
23.04.2015,11:14:58,$HST:Measurement stop
23.04.2015,11:14:58,$CRX:Stopped
23.04.2015,11:14:58,$HST:Measurement wait...
23.04.2015,11:14:59,$HST:Measurement halted
23.04.2015,11:14:59,$HST:Measurement idle
23.04.2015,11:14:59,$CRX:Stopped
23.04.2015,11:15:00,$HST:Measurement enable
23.04.2015,11:15:00,$CRX:AGC gain = 1.55V
23.04.2015,11:15:00,$CRX:Emitter BF199 = 0.14V
23.04.2015,11:15:00,$CRX:Analog Input = 9.24
23.04.2015,11:15:00,$HST:Autostart via scheduler
23.04.2015,11:15:00,$HST:Param. RCU due to START
23.04.2015,11:15:00,$HST:Actual focuscode 25
23.04.2015,11:15:00,$HST:Enable data transfer
23.04.2015,11:15:00,$HST:Receiver calibration
23.04.2015,11:15:00,$CRX:Started
23.04.2015,11:15:00,$HST:Start new FITS-file
23.04.2015,11:15:00,$HST:Continous measurement
23.04.2015,11:24:46,$HST:Measurement stop
23.04.2015,11:24:46,$HST:FITS #10 200rows x 2343cols
23.04.2015,11:24:46,$HST:Measurement wait...
23.04.2015,11:24:46,$HST:EOT (&) detected
23.04.2015,11:24:46,$HST:Measurement halted
23.04.2015,11:24:46,$HST:Measurement idle
23.04.2015,11:24:46,$CRX:Stopped
23.04.2015,11:24:47,$HST:Measurement enable
23.04.2015,11:24:47,$CRX:AGC gain = 1.57V
23.04.2015,11:24:47,$CRX:Emitter BF199 = 0.14V
23.04.2015,11:24:47,$CRX:Analog Input = 9.24
23.04.2015,11:24:47,$HST:Start overview...
23.04.2015,11:24:47,$HST:Wait ~45sec please!
23.04.2015,11:25:29,$HST:End spectral overview...
23.04.2015,11:25:29,$HST:Data in log-directory
23.04.2015,11:46:50,$HST:Param. RCU due to START
23.04.2015,11:46:50,$HST:Actual focuscode 02
23.04.2015,11:46:51,$HST:Enable data transfer
23.04.2015,11:46:51,$HST:Receiver calibration
23.04.2015,11:46:51,$CRX:Started
23.04.2015,11:46:51,$HST:Start new FITS-file
23.04.2015,11:46:51,$HST:Continous measurement
23.04.2015,11:54:56,$HST:Measurement stop
23.04.2015,11:54:56,$HST:FITS #11 200rows x 1940cols
23.04.2015,11:54:56,$HST:Measurement wait...
23.04.2015,11:54:56,$HST:EOT (&) detected
23.04.2015,11:54:56,$HST:Measurement halted
23.04.2015,11:54:56,$HST:Measurement idle
23.04.2015,11:54:56,$CRX:Stopped
23.04.2015,11:54:57,$HST:Measurement enable
23.04.2015,11:54:57,$CRX:AGC gain = 1.57V
23.04.2015,11:54:57,$CRX:Emitter BF199 = 0.14V
23.04.2015,11:54:57,$CRX:Analog Input = 9.24
23.04.2015,11:54:58,$HST:Start overview...
23.04.2015,11:54:58,$HST:Wait ~45sec please!
23.04.2015,11:55:40,$HST:End spectral overview...
23.04.2015,11:55:40,$HST:Data in log-directory
23.04.2015,11:56:47,$HST:Param. RCU due to START
23.04.2015,11:56:47,$HST:Actual focuscode 02
23.04.2015,11:56:47,$HST:Enable data transfer
23.04.2015,11:56:47,$HST:Receiver calibration
23.04.2015,11:56:47,$CRX:Started
23.04.2015,11:56:47,$HST:Start new FITS-file
23.04.2015,11:56:47,$HST:Continous measurement
23.04.2015,11:57:22,$HST:Measurement stop
23.04.2015,11:57:22,$HST:FITS #12 200rows x 141cols
23.04.2015,11:57:22,$HST:Measurement wait...
23.04.2015,11:57:23,$HST:EOT (&) detected
23.04.2015,11:57:23,$HST:Measurement halted
23.04.2015,11:57:23,$HST:Measurement idle
23.04.2015,11:57:23,$CRX:Stopped
23.04.2015,11:57:23,$HST:Measurement enable
23.04.2015,11:57:23,$CRX:AGC gain = 1.57V
23.04.2015,11:57:23,$CRX:Emitter BF199 = 0.14V
23.04.2015,11:57:23,$CRX:Analog Input = 9.24
23.04.2015,11:57:25,$HST:Start overview...
23.04.2015,11:57:25,$HST:Wait ~45sec please!
23.04.2015,11:58:06,$HST:End spectral overview...
23.04.2015,11:58:06,$HST:Data in log-directory
23.04.2015,12:10:53,$HST:Param. RCU due to START
23.04.2015,12:10:53,$HST:Actual focuscode 02
23.04.2015,12:10:54,$HST:Enable data transfer
23.04.2015,12:10:54,$HST:Receiver calibration
23.04.2015,12:10:54,$CRX:Started
23.04.2015,12:10:54,$HST:Start new FITS-file
23.04.2015,12:10:54,$HST:Continous measurement
23.04.2015,12:11:04,$HST:Measurement stop
23.04.2015,12:11:04,$HST:FITS #13 200rows x 40cols
23.04.2015,12:11:04,$HST:Measurement wait...
23.04.2015,12:11:04,$HST:EOT (&) detected
23.04.2015,12:11:04,$HST:Measurement halted
23.04.2015,12:11:05,$HST:Measurement idle
23.04.2015,12:11:05,$CRX:Stopped
23.04.2015,12:11:05,$HST:Measurement enable
23.04.2015,12:11:05,$CRX:AGC gain = 1.57V
23.04.2015,12:11:05,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:11:05,$CRX:Analog Input = 9.24
23.04.2015,12:11:05,$HST:Start overview...
23.04.2015,12:11:05,$HST:Wait ~45sec please!
23.04.2015,12:11:47,$HST:End spectral overview...
23.04.2015,12:11:47,$HST:Data in log-directory
23.04.2015,12:12:14,$HST:Param. RCU due to START
23.04.2015,12:12:14,$HST:Actual focuscode 02
23.04.2015,12:12:14,$HST:Enable data transfer
23.04.2015,12:12:14,$HST:Receiver calibration
23.04.2015,12:12:14,$CRX:Started
23.04.2015,12:12:15,$HST:Start new FITS-file
23.04.2015,12:12:15,$HST:Continous measurement
23.04.2015,12:18:42,$HST:Measurement stop
23.04.2015,12:18:42,$HST:FITS #14 200rows x 1548cols
23.04.2015,12:18:42,$HST:Measurement wait...
23.04.2015,12:18:42,$HST:EOT (&) detected
23.04.2015,12:18:42,$HST:Measurement halted
23.04.2015,12:18:42,$HST:Measurement idle
23.04.2015,12:18:42,$CRX:Stopped
23.04.2015,12:18:42,$HST:Measurement enable
23.04.2015,12:18:42,$CRX:AGC gain = 1.57V
23.04.2015,12:18:42,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:18:42,$CRX:Analog Input = 9.24
23.04.2015,12:18:43,$HST:Start overview...
23.04.2015,12:18:43,$HST:Wait ~45sec please!
23.04.2015,12:19:25,$HST:End spectral overview...
23.04.2015,12:19:25,$HST:Data in log-directory
23.04.2015,12:29:51,$HST:Param. RCU due to START
23.04.2015,12:29:51,$HST:Actual focuscode 02
23.04.2015,12:29:51,$HST:Enable data transfer
23.04.2015,12:29:51,$HST:Receiver calibration
23.04.2015,12:29:51,$CRX:Started
23.04.2015,12:29:52,$HST:Start new FITS-file
23.04.2015,12:29:52,$HST:Continous measurement
23.04.2015,12:30:02,$HST:Measurement stop
23.04.2015,12:30:02,$HST:FITS #15 200rows x 41cols
23.04.2015,12:30:02,$HST:Measurement wait...
23.04.2015,12:30:02,$HST:EOT (&) detected
23.04.2015,12:30:02,$HST:Measurement halted
23.04.2015,12:30:02,$HST:Measurement idle
23.04.2015,12:30:02,$CRX:Stopped
23.04.2015,12:30:03,$HST:Measurement enable
23.04.2015,12:30:03,$CRX:AGC gain = 1.57V
23.04.2015,12:30:03,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:30:03,$CRX:Analog Input = 9.24
23.04.2015,12:30:03,$HST:Start overview...
23.04.2015,12:30:03,$HST:Wait ~45sec please!
23.04.2015,12:30:45,$HST:End spectral overview...
23.04.2015,12:30:45,$HST:Data in log-directory
23.04.2015,12:31:06,$HST:Param. RCU due to START
23.04.2015,12:31:06,$HST:Actual focuscode 02
23.04.2015,12:31:06,$HST:Enable data transfer
23.04.2015,12:31:06,$HST:Receiver calibration
23.04.2015,12:31:06,$CRX:Started
23.04.2015,12:31:06,$HST:Start new FITS-file
23.04.2015,12:31:07,$HST:Continous measurement
23.04.2015,12:36:50,$HST:Measurement stop
23.04.2015,12:36:50,$HST:FITS #16 200rows x 1376cols
23.04.2015,12:36:50,$HST:Measurement wait...
23.04.2015,12:36:51,$HST:EOT (&) detected
23.04.2015,12:36:51,$HST:Measurement halted
23.04.2015,12:36:51,$HST:Measurement idle
23.04.2015,12:36:51,$CRX:Stopped
23.04.2015,12:36:51,$HST:Measurement enable
23.04.2015,12:36:51,$CRX:AGC gain = 1.57V
23.04.2015,12:36:51,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:36:51,$CRX:Analog Input = 9.24
23.04.2015,12:36:52,$HST:Start overview...
23.04.2015,12:36:52,$HST:Wait ~45sec please!
23.04.2015,12:37:34,$HST:End spectral overview...
23.04.2015,12:37:34,$HST:Data in log-directory
23.04.2015,12:39:46,$HST:Param. RCU due to START
23.04.2015,12:39:46,$HST:Actual focuscode 02
23.04.2015,12:39:46,$HST:Enable data transfer
23.04.2015,12:39:46,$HST:Receiver calibration
23.04.2015,12:39:46,$CRX:Started
23.04.2015,12:39:46,$HST:Start new FITS-file
23.04.2015,12:39:47,$HST:Continous measurement
23.04.2015,12:43:08,$CRX:e-Callisto ETH Zurich
23.04.2015,12:43:08,$HST:Watchdog triggered -> Reset
23.04.2015,12:43:08,$CRX:V1.5, 2006-11-04
23.04.2015,12:43:08,$CRX:ChargePump=On
23.04.2015,12:43:08,$HST:CD1316LV/IV detected
23.04.2015,12:43:08,$CRX:Debug=Off
23.04.2015,12:43:08,$CRX:Trigger=No
23.04.2015,12:43:08,$CRX:FPUcodex=0
23.04.2015,12:43:08,$CRX:GS =13
23.04.2015,12:43:08,$CRX:GA =253
23.04.2015,12:43:08,$CRX:Delay=0msec
23.04.2015,12:43:08,$CRX:Frequency=0.0MHz
23.04.2015,12:43:08,$HST:Receiver connected
23.04.2015,12:43:08,$CRX:Sweeplength=0
23.04.2015,12:43:08,$CRX:low_band_max=171MHz
23.04.2015,12:43:08,$CRX:mid_band_max=450MHz
23.04.2015,12:43:08,$CRX:high_band_max=863MHz
23.04.2015,12:43:08,$CRX:Idle=0x
23.04.2015,12:43:08,$CRX:ChargePump=On
23.04.2015,12:43:08,$HST:CD1316LV/IV detected
23.04.2015,12:43:08,$CRX:Debug=Off
23.04.2015,12:43:08,$CRX:Trigger=Extern
23.04.2015,12:43:08,$CRX:FPUcodex=0
23.04.2015,12:43:08,$CRX:GS =13
23.04.2015,12:43:08,$CRX:GA =624
23.04.2015,12:43:08,$CRX:Delay=0msec
23.04.2015,12:43:08,$CRX:Frequency=45.0MHz
23.04.2015,12:43:08,$HST:Receiver connected
23.04.2015,12:43:08,$CRX:Sweeplength=200
23.04.2015,12:43:08,$CRX:low_band_max=171MHz
23.04.2015,12:43:08,$CRX:mid_band_max=450MHz
23.04.2015,12:43:08,$CRX:high_band_max=863MHz
23.04.2015,12:43:08,$CRX:Idle=0x
23.04.2015,12:43:11,$HST:Auto stop due to data loss.
23.04.2015,12:43:11,$HST:Measurement stop
23.04.2015,12:43:11,$HST:Measurement wait...
23.04.2015,12:43:12,$HST:Measurement halted
23.04.2015,12:43:12,$HST:Measurement idle
23.04.2015,12:43:12,$CRX:Stopped
23.04.2015,12:43:12,$HST:Measurement enable
23.04.2015,12:43:12,$CRX:AGC gain = 1.57V
23.04.2015,12:43:12,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:43:12,$CRX:Analog Input = 9.24
23.04.2015,12:43:14,$HST:Check RS232-connection!
23.04.2015,12:43:17,$HST:Attempting Auto-Start
23.04.2015,12:43:17,$HST:Param. RCU due to START
23.04.2015,12:43:17,$HST:Actual focuscode 02
23.04.2015,12:43:17,$HST:Enable data transfer
23.04.2015,12:43:17,$HST:Receiver calibration
23.04.2015,12:43:17,$CRX:Started
23.04.2015,12:43:17,$HST:Start new FITS-file
23.04.2015,12:43:17,$HST:Continous measurement
23.04.2015,12:43:19,$CRX:e-Callisto ETH Zurich
23.04.2015,12:43:19,$HST:Watchdog triggered -> Reset
23.04.2015,12:43:19,$CRX:V1.5, 2006-11-04
23.04.2015,12:43:19,$CRX:ChargePump=On
23.04.2015,12:43:19,$HST:CD1316LV/IV detected
23.04.2015,12:43:19,$CRX:Debug=Off
23.04.2015,12:43:19,$CRX:Trigger=No
23.04.2015,12:43:19,$CRX:FPUcodex=0
23.04.2015,12:43:19,$CRX:GS =13
23.04.2015,12:43:19,$CRX:GA =253
23.04.2015,12:43:19,$CRX:Delay=0msec
23.04.2015,12:43:19,$CRX:Frequency=0.0MHz
23.04.2015,12:43:19,$HST:Receiver connected
23.04.2015,12:43:19,$CRX:Sweeplength=0
23.04.2015,12:43:19,$CRX:low_band_max=171MHz
23.04.2015,12:43:19,$CRX:mid_band_max=450MHz
23.04.2015,12:43:19,$CRX:high_band_max=863MHz
23.04.2015,12:43:19,$CRX:Idle=0x
23.04.2015,12:43:19,$CRX:ChargePump=On
23.04.2015,12:43:19,$HST:CD1316LV/IV detected
23.04.2015,12:43:19,$CRX:Debug=Off
23.04.2015,12:43:19,$CRX:Trigger=Extern
23.04.2015,12:43:19,$CRX:FPUcodex=0
23.04.2015,12:43:19,$CRX:GS =13
23.04.2015,12:43:19,$CRX:GA =624
23.04.2015,12:43:19,$CRX:Delay=0msec
23.04.2015,12:43:19,$CRX:Frequency=45.0MHz
23.04.2015,12:43:19,$HST:Receiver connected
23.04.2015,12:43:19,$CRX:Sweeplength=200
23.04.2015,12:43:19,$CRX:low_band_max=171MHz
23.04.2015,12:43:19,$CRX:mid_band_max=450MHz
23.04.2015,12:43:19,$CRX:high_band_max=863MHz
23.04.2015,12:43:19,$CRX:Idle=0x
23.04.2015,12:43:22,$HST:Auto stop due to data loss.
23.04.2015,12:43:22,$HST:Measurement stop
23.04.2015,12:43:22,$HST:Measurement wait...
23.04.2015,12:43:23,$HST:Measurement halted
23.04.2015,12:43:23,$HST:Measurement idle
23.04.2015,12:43:23,$CRX:Stopped
23.04.2015,12:43:24,$HST:Measurement enable
23.04.2015,12:43:24,$CRX:AGC gain = 1.57V
23.04.2015,12:43:24,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:43:24,$CRX:Analog Input = 9.24
23.04.2015,12:43:25,$HST:Check RS232-connection!
23.04.2015,12:43:28,$HST:Attempting Auto-Start
23.04.2015,12:43:28,$HST:Param. RCU due to START
23.04.2015,12:43:28,$HST:Actual focuscode 02
23.04.2015,12:43:28,$HST:Enable data transfer
23.04.2015,12:43:28,$HST:Receiver calibration
23.04.2015,12:43:28,$CRX:Started
23.04.2015,12:43:29,$HST:Start new FITS-file
23.04.2015,12:43:29,$HST:Continous measurement
23.04.2015,12:43:31,$CRX:e-Callisto ETH Zurich
23.04.2015,12:43:31,$HST:Watchdog triggered -> Reset
23.04.2015,12:43:31,$CRX:V1.5, 2006-11-04
23.04.2015,12:43:31,$CRX:ChargePump=On
23.04.2015,12:43:31,$HST:CD1316LV/IV detected
23.04.2015,12:43:31,$CRX:Debug=Off
23.04.2015,12:43:31,$CRX:Trigger=No
23.04.2015,12:43:31,$CRX:FPUcodex=0
23.04.2015,12:43:31,$CRX:GS =13
23.04.2015,12:43:31,$CRX:GA =253
23.04.2015,12:43:31,$CRX:Delay=0msec
23.04.2015,12:43:31,$CRX:Frequency=0.0MHz
23.04.2015,12:43:31,$HST:Receiver connected
23.04.2015,12:43:31,$CRX:Sweeplength=0
23.04.2015,12:43:31,$CRX:low_band_max=171MHz
23.04.2015,12:43:31,$CRX:mid_band_max=450MHz
23.04.2015,12:43:31,$CRX:high_band_max=863MHz
23.04.2015,12:43:31,$CRX:Idle=0x
23.04.2015,12:43:31,$CRX:ChargePump=On
23.04.2015,12:43:31,$HST:CD1316LV/IV detected
23.04.2015,12:43:31,$CRX:Debug=Off
23.04.2015,12:43:31,$CRX:Trigger=Extern
23.04.2015,12:43:31,$CRX:FPUcodex=0
23.04.2015,12:43:31,$CRX:GS =13
23.04.2015,12:43:31,$CRX:GA =624
23.04.2015,12:43:31,$CRX:Delay=0msec
23.04.2015,12:43:31,$CRX:Frequency=45.0MHz
23.04.2015,12:43:31,$HST:Receiver connected
23.04.2015,12:43:31,$CRX:Sweeplength=200
23.04.2015,12:43:31,$CRX:low_band_max=171MHz
23.04.2015,12:43:31,$CRX:mid_band_max=450MHz
23.04.2015,12:43:31,$CRX:high_band_max=863MHz
23.04.2015,12:43:31,$CRX:Idle=0x
23.04.2015,12:43:34,$HST:Auto stop due to data loss.
23.04.2015,12:43:34,$HST:Measurement stop
23.04.2015,12:43:34,$HST:Measurement wait...
23.04.2015,12:43:35,$HST:Measurement halted
23.04.2015,12:43:35,$HST:Measurement idle
23.04.2015,12:43:35,$CRX:Stopped
23.04.2015,12:43:35,$HST:Measurement enable
23.04.2015,12:43:35,$CRX:AGC gain = 1.56V
23.04.2015,12:43:35,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:43:35,$CRX:Analog Input = 9.24
23.04.2015,12:43:37,$HST:Check RS232-connection!
23.04.2015,12:43:40,$HST:Attempting Auto-Start
23.04.2015,12:43:40,$HST:Param. RCU due to START
23.04.2015,12:43:40,$HST:Actual focuscode 02
23.04.2015,12:43:40,$HST:Enable data transfer
23.04.2015,12:43:40,$HST:Receiver calibration
23.04.2015,12:43:40,$CRX:Started
23.04.2015,12:43:40,$HST:Start new FITS-file
23.04.2015,12:43:40,$HST:Continous measurement
23.04.2015,12:43:42,$CRX:e-Callisto ETH Zurich
23.04.2015,12:43:42,$HST:Watchdog triggered -> Reset
23.04.2015,12:43:42,$CRX:V1.5, 2006-11-04
23.04.2015,12:43:42,$CRX:ChargePump=On
23.04.2015,12:43:42,$HST:CD1316LV/IV detected
23.04.2015,12:43:42,$CRX:Debug=Off
23.04.2015,12:43:42,$CRX:Trigger=No
23.04.2015,12:43:42,$CRX:FPUcodex=0
23.04.2015,12:43:42,$CRX:GS =13
23.04.2015,12:43:42,$CRX:GA =253
23.04.2015,12:43:42,$CRX:Delay=0msec
23.04.2015,12:43:42,$CRX:Frequency=0.0MHz
23.04.2015,12:43:42,$HST:Receiver connected
23.04.2015,12:43:42,$CRX:Sweeplength=0
23.04.2015,12:43:42,$CRX:low_band_max=171MHz
23.04.2015,12:43:42,$CRX:mid_band_max=450MHz
23.04.2015,12:43:42,$CRX:high_band_max=863MHz
23.04.2015,12:43:42,$CRX:Idle=0x
23.04.2015,12:43:42,$CRX:ChargePump=On
23.04.2015,12:43:42,$HST:CD1316LV/IV detected
23.04.2015,12:43:42,$CRX:Debug=Off
23.04.2015,12:43:42,$CRX:Trigger=Extern
23.04.2015,12:43:42,$CRX:FPUcodex=0
23.04.2015,12:43:42,$CRX:GS =13
23.04.2015,12:43:42,$CRX:GA =624
23.04.2015,12:43:42,$CRX:Delay=0msec
23.04.2015,12:43:42,$CRX:Frequency=45.0MHz
23.04.2015,12:43:42,$HST:Receiver connected
23.04.2015,12:43:42,$CRX:Sweeplength=200
23.04.2015,12:43:42,$CRX:low_band_max=171MHz
23.04.2015,12:43:42,$CRX:mid_band_max=450MHz
23.04.2015,12:43:42,$CRX:high_band_max=863MHz
23.04.2015,12:43:42,$CRX:Idle=0x
23.04.2015,12:43:45,$HST:Auto stop due to data loss.
23.04.2015,12:43:45,$HST:Measurement stop
23.04.2015,12:43:45,$HST:Measurement wait...
23.04.2015,12:43:46,$HST:Measurement halted
23.04.2015,12:43:46,$HST:Measurement idle
23.04.2015,12:43:46,$CRX:Stopped
23.04.2015,12:43:46,$HST:Measurement enable
23.04.2015,12:43:46,$CRX:AGC gain = 1.57V
23.04.2015,12:43:46,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:43:46,$CRX:Analog Input = 9.24
23.04.2015,12:43:48,$HST:Check RS232-connection!
23.04.2015,12:43:51,$HST:Attempting Auto-Start
23.04.2015,12:43:51,$HST:Param. RCU due to START
23.04.2015,12:43:51,$HST:Actual focuscode 02
23.04.2015,12:43:51,$HST:Enable data transfer
23.04.2015,12:43:51,$HST:Receiver calibration
23.04.2015,12:43:51,$CRX:Started
23.04.2015,12:43:51,$HST:Start new FITS-file
23.04.2015,12:43:52,$HST:Continous measurement
23.04.2015,12:43:53,$CRX:e-Callisto ETH Zurich
23.04.2015,12:43:53,$HST:Watchdog triggered -> Reset
23.04.2015,12:43:53,$CRX:V1.5, 2006-11-04
23.04.2015,12:43:54,$CRX:ChargePump=On
23.04.2015,12:43:54,$HST:CD1316LV/IV detected
23.04.2015,12:43:54,$CRX:Debug=Off
23.04.2015,12:43:54,$CRX:Trigger=No
23.04.2015,12:43:54,$CRX:FPUcodex=0
23.04.2015,12:43:54,$CRX:GS =13
23.04.2015,12:43:54,$CRX:GA =253
23.04.2015,12:43:54,$CRX:Delay=0msec
23.04.2015,12:43:54,$CRX:Frequency=0.0MHz
23.04.2015,12:43:54,$HST:Receiver connected
23.04.2015,12:43:54,$CRX:Sweeplength=0
23.04.2015,12:43:54,$CRX:low_band_max=171MHz
23.04.2015,12:43:54,$CRX:mid_band_max=450MHz
23.04.2015,12:43:54,$CRX:high_band_max=863MHz
23.04.2015,12:43:54,$CRX:Idle=0x
23.04.2015,12:43:54,$CRX:ChargePump=On
23.04.2015,12:43:54,$HST:CD1316LV/IV detected
23.04.2015,12:43:54,$CRX:Debug=Off
23.04.2015,12:43:54,$CRX:Trigger=Extern
23.04.2015,12:43:54,$CRX:FPUcodex=0
23.04.2015,12:43:54,$CRX:GS =13
23.04.2015,12:43:54,$CRX:GA =624
23.04.2015,12:43:54,$CRX:Delay=0msec
23.04.2015,12:43:54,$CRX:Frequency=45.0MHz
23.04.2015,12:43:54,$HST:Receiver connected
23.04.2015,12:43:54,$CRX:Sweeplength=200
23.04.2015,12:43:54,$CRX:low_band_max=171MHz
23.04.2015,12:43:54,$CRX:mid_band_max=450MHz
23.04.2015,12:43:54,$CRX:high_band_max=863MHz
23.04.2015,12:43:54,$CRX:Idle=0x
23.04.2015,12:43:56,$HST:Auto stop due to data loss.
23.04.2015,12:43:57,$HST:Measurement stop
23.04.2015,12:43:57,$HST:Measurement wait...
23.04.2015,12:43:57,$HST:Measurement halted
23.04.2015,12:43:58,$HST:Measurement idle
23.04.2015,12:43:58,$CRX:Stopped
23.04.2015,12:43:58,$HST:Measurement enable
23.04.2015,12:43:58,$CRX:AGC gain = 1.57V
23.04.2015,12:43:58,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:43:58,$CRX:Analog Input = 9.24
23.04.2015,12:43:59,$HST:Check RS232-connection!
23.04.2015,12:44:02,$HST:Attempting Auto-Start
23.04.2015,12:44:03,$HST:Param. RCU due to START
23.04.2015,12:44:03,$HST:Actual focuscode 02
23.04.2015,12:44:03,$HST:Enable data transfer
23.04.2015,12:44:03,$HST:Receiver calibration
23.04.2015,12:44:03,$CRX:Started
23.04.2015,12:44:03,$HST:Start new FITS-file
23.04.2015,12:44:03,$HST:Continous measurement
23.04.2015,12:44:05,$CRX:e-Callisto ETH Zurich
23.04.2015,12:44:05,$HST:Watchdog triggered -> Reset
23.04.2015,12:44:05,$CRX:V1.5, 2006-11-04
23.04.2015,12:44:05,$CRX:ChargePump=On
23.04.2015,12:44:05,$HST:CD1316LV/IV detected
23.04.2015,12:44:05,$CRX:Debug=Off
23.04.2015,12:44:05,$CRX:Trigger=No
23.04.2015,12:44:05,$CRX:FPUcodex=0
23.04.2015,12:44:05,$CRX:GS =13
23.04.2015,12:44:05,$CRX:GA =253
23.04.2015,12:44:05,$CRX:Delay=0msec
23.04.2015,12:44:05,$CRX:Frequency=0.0MHz
23.04.2015,12:44:05,$HST:Receiver connected
23.04.2015,12:44:05,$CRX:Sweeplength=0
23.04.2015,12:44:05,$CRX:low_band_max=171MHz
23.04.2015,12:44:05,$CRX:mid_band_max=450MHz
23.04.2015,12:44:05,$CRX:high_band_max=863MHz
23.04.2015,12:44:05,$CRX:Idle=0x
23.04.2015,12:44:05,$CRX:ChargePump=On
23.04.2015,12:44:05,$HST:CD1316LV/IV detected
23.04.2015,12:44:05,$CRX:Debug=Off
23.04.2015,12:44:05,$CRX:Trigger=Extern
23.04.2015,12:44:05,$CRX:FPUcodex=0
23.04.2015,12:44:05,$CRX:GS =13
23.04.2015,12:44:05,$CRX:GA =624
23.04.2015,12:44:05,$CRX:Delay=0msec
23.04.2015,12:44:05,$CRX:Frequency=45.0MHz
23.04.2015,12:44:05,$HST:Receiver connected
23.04.2015,12:44:05,$CRX:Sweeplength=200
23.04.2015,12:44:05,$CRX:low_band_max=171MHz
23.04.2015,12:44:05,$CRX:mid_band_max=450MHz
23.04.2015,12:44:05,$CRX:high_band_max=863MHz
23.04.2015,12:44:05,$CRX:Idle=0x
23.04.2015,12:44:08,$HST:Auto stop due to data loss.
23.04.2015,12:44:08,$HST:Measurement stop
23.04.2015,12:44:08,$HST:Measurement wait...
23.04.2015,12:44:09,$HST:Measurement halted
23.04.2015,12:44:09,$HST:Measurement idle
23.04.2015,12:44:09,$CRX:Stopped
23.04.2015,12:44:09,$HST:Measurement enable
23.04.2015,12:44:09,$CRX:AGC gain = 1.57V
23.04.2015,12:44:09,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:44:09,$CRX:Analog Input = 9.24
23.04.2015,12:44:11,$HST:Check RS232-connection!
23.04.2015,12:44:14,$HST:Attempting Auto-Start
23.04.2015,12:44:14,$HST:Param. RCU due to START
23.04.2015,12:44:14,$HST:Actual focuscode 02
23.04.2015,12:44:14,$HST:Enable data transfer
23.04.2015,12:44:14,$HST:Receiver calibration
23.04.2015,12:44:14,$CRX:Started
23.04.2015,12:44:14,$HST:Start new FITS-file
23.04.2015,12:44:15,$HST:Continous measurement
23.04.2015,12:44:16,$CRX:e-Callisto ETH Zurich
23.04.2015,12:44:16,$HST:Watchdog triggered -> Reset
23.04.2015,12:44:16,$CRX:V1.5, 2006-11-04
23.04.2015,12:44:16,$CRX:ChargePump=On
23.04.2015,12:44:16,$HST:CD1316LV/IV detected
23.04.2015,12:44:16,$CRX:Debug=Off
23.04.2015,12:44:16,$CRX:Trigger=No
23.04.2015,12:44:16,$CRX:FPUcodex=0
23.04.2015,12:44:16,$CRX:GS =13
23.04.2015,12:44:16,$CRX:GA =253
23.04.2015,12:44:16,$CRX:Delay=0msec
23.04.2015,12:44:16,$CRX:Frequency=0.0MHz
23.04.2015,12:44:16,$HST:Receiver connected
23.04.2015,12:44:16,$CRX:Sweeplength=0
23.04.2015,12:44:16,$CRX:low_band_max=171MHz
23.04.2015,12:44:16,$CRX:mid_band_max=450MHz
23.04.2015,12:44:16,$CRX:high_band_max=863MHz
23.04.2015,12:44:16,$CRX:Idle=0x
23.04.2015,12:44:16,$CRX:ChargePump=On
23.04.2015,12:44:16,$HST:CD1316LV/IV detected
23.04.2015,12:44:16,$CRX:Debug=Off
23.04.2015,12:44:16,$CRX:Trigger=Extern
23.04.2015,12:44:16,$CRX:FPUcodex=0
23.04.2015,12:44:16,$CRX:GS =13
23.04.2015,12:44:16,$CRX:GA =624
23.04.2015,12:44:16,$CRX:Delay=0msec
23.04.2015,12:44:16,$CRX:Frequency=45.0MHz
23.04.2015,12:44:16,$HST:Receiver connected
23.04.2015,12:44:16,$CRX:Sweeplength=200
23.04.2015,12:44:16,$CRX:low_band_max=171MHz
23.04.2015,12:44:16,$CRX:mid_band_max=450MHz
23.04.2015,12:44:16,$CRX:high_band_max=863MHz
23.04.2015,12:44:16,$CRX:Idle=0x
23.04.2015,12:44:19,$HST:Auto stop due to data loss.
23.04.2015,12:44:19,$HST:Measurement stop
23.04.2015,12:44:20,$HST:Measurement wait...
23.04.2015,12:44:20,$HST:Measurement halted
23.04.2015,12:44:21,$HST:Measurement idle
23.04.2015,12:44:21,$CRX:Stopped
23.04.2015,12:44:21,$HST:Measurement enable
23.04.2015,12:44:21,$CRX:AGC gain = 1.57V
23.04.2015,12:44:21,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:44:21,$CRX:Analog Input = 9.24
23.04.2015,12:44:22,$HST:Check RS232-connection!
23.04.2015,12:44:25,$HST:Attempting Auto-Start
23.04.2015,12:44:25,$HST:Param. RCU due to START
23.04.2015,12:44:25,$HST:Actual focuscode 02
23.04.2015,12:44:26,$HST:Enable data transfer
23.04.2015,12:44:26,$HST:Receiver calibration
23.04.2015,12:44:26,$CRX:Started
23.04.2015,12:44:26,$HST:Start new FITS-file
23.04.2015,12:44:26,$HST:Continous measurement
23.04.2015,12:44:28,$CRX:e-Callisto ETH Zurich
23.04.2015,12:44:28,$HST:Watchdog triggered -> Reset
23.04.2015,12:44:28,$CRX:V1.5, 2006-11-04
23.04.2015,12:44:28,$CRX:ChargePump=On
23.04.2015,12:44:28,$HST:CD1316LV/IV detected
23.04.2015,12:44:28,$CRX:Debug=Off
23.04.2015,12:44:28,$CRX:Trigger=No
23.04.2015,12:44:28,$CRX:FPUcodex=0
23.04.2015,12:44:28,$CRX:GS =13
23.04.2015,12:44:28,$CRX:GA =253
23.04.2015,12:44:28,$CRX:Delay=0msec
23.04.2015,12:44:28,$CRX:Frequency=0.0MHz
23.04.2015,12:44:28,$HST:Receiver connected
23.04.2015,12:44:28,$CRX:Sweeplength=0
23.04.2015,12:44:28,$CRX:low_band_max=171MHz
23.04.2015,12:44:28,$CRX:mid_band_max=450MHz
23.04.2015,12:44:28,$CRX:high_band_max=863MHz
23.04.2015,12:44:28,$CRX:Idle=0x
23.04.2015,12:44:28,$CRX:ChargePump=On
23.04.2015,12:44:28,$HST:CD1316LV/IV detected
23.04.2015,12:44:28,$CRX:Debug=Off
23.04.2015,12:44:28,$CRX:Trigger=Extern
23.04.2015,12:44:28,$CRX:FPUcodex=0
23.04.2015,12:44:28,$CRX:GS =13
23.04.2015,12:44:28,$CRX:GA =624
23.04.2015,12:44:28,$CRX:Delay=0msec
23.04.2015,12:44:28,$CRX:Frequency=45.0MHz
23.04.2015,12:44:28,$HST:Receiver connected
23.04.2015,12:44:28,$CRX:Sweeplength=200
23.04.2015,12:44:28,$CRX:low_band_max=171MHz
23.04.2015,12:44:28,$CRX:mid_band_max=450MHz
23.04.2015,12:44:28,$CRX:high_band_max=863MHz
23.04.2015,12:44:28,$CRX:Idle=0x
23.04.2015,12:44:31,$HST:Auto stop due to data loss.
23.04.2015,12:44:31,$HST:Measurement stop
23.04.2015,12:44:31,$HST:Measurement wait...
23.04.2015,12:44:32,$HST:Measurement halted
23.04.2015,12:44:32,$HST:Measurement idle
23.04.2015,12:44:32,$CRX:Stopped
23.04.2015,12:44:32,$HST:Measurement enable
23.04.2015,12:44:32,$CRX:AGC gain = 1.57V
23.04.2015,12:44:32,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:44:32,$CRX:Analog Input = 9.24
23.04.2015,12:44:34,$HST:Check RS232-connection!
23.04.2015,12:44:37,$HST:Attempting Auto-Start
23.04.2015,12:44:37,$HST:Param. RCU due to START
23.04.2015,12:44:37,$HST:Actual focuscode 02
23.04.2015,12:44:37,$HST:Enable data transfer
23.04.2015,12:44:37,$HST:Receiver calibration
23.04.2015,12:44:37,$CRX:Started
23.04.2015,12:44:37,$HST:Start new FITS-file
23.04.2015,12:44:37,$HST:Continous measurement
23.04.2015,12:44:39,$CRX:e-Callisto ETH Zurich
23.04.2015,12:44:39,$HST:Watchdog triggered -> Reset
23.04.2015,12:44:39,$CRX:V1.5, 2006-11-04
23.04.2015,12:44:39,$CRX:ChargePump=On
23.04.2015,12:44:39,$HST:CD1316LV/IV detected
23.04.2015,12:44:39,$CRX:Debug=Off
23.04.2015,12:44:39,$CRX:Trigger=No
23.04.2015,12:44:39,$CRX:FPUcodex=0
23.04.2015,12:44:39,$CRX:GS =13
23.04.2015,12:44:39,$CRX:GA =253
23.04.2015,12:44:39,$CRX:Delay=0msec
23.04.2015,12:44:39,$CRX:Frequency=0.0MHz
23.04.2015,12:44:39,$HST:Receiver connected
23.04.2015,12:44:39,$CRX:Sweeplength=0
23.04.2015,12:44:39,$CRX:low_band_max=171MHz
23.04.2015,12:44:39,$CRX:mid_band_max=450MHz
23.04.2015,12:44:39,$CRX:high_band_max=863MHz
23.04.2015,12:44:39,$CRX:Idle=0x
23.04.2015,12:44:39,$CRX:ChargePump=On
23.04.2015,12:44:39,$HST:CD1316LV/IV detected
23.04.2015,12:44:39,$CRX:Debug=Off
23.04.2015,12:44:39,$CRX:Trigger=Extern
23.04.2015,12:44:39,$CRX:FPUcodex=0
23.04.2015,12:44:39,$CRX:GS =13
23.04.2015,12:44:39,$CRX:GA =624
23.04.2015,12:44:39,$CRX:Delay=0msec
23.04.2015,12:44:39,$CRX:Frequency=45.0MHz
23.04.2015,12:44:39,$HST:Receiver connected
23.04.2015,12:44:39,$CRX:Sweeplength=200
23.04.2015,12:44:39,$CRX:low_band_max=171MHz
23.04.2015,12:44:39,$CRX:mid_band_max=450MHz
23.04.2015,12:44:39,$CRX:high_band_max=863MHz
23.04.2015,12:44:39,$CRX:Idle=0x
23.04.2015,12:44:42,$HST:Auto stop due to data loss.
23.04.2015,12:44:42,$HST:Measurement stop
23.04.2015,12:44:42,$HST:Measurement wait...
23.04.2015,12:44:43,$HST:Measurement halted
23.04.2015,12:44:43,$HST:Measurement idle
23.04.2015,12:44:43,$CRX:Stopped
23.04.2015,12:44:44,$HST:Measurement enable
23.04.2015,12:44:44,$CRX:AGC gain = 1.57V
23.04.2015,12:44:44,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:44:44,$CRX:Analog Input = 9.24
23.04.2015,12:44:45,$HST:Check RS232-connection!
23.04.2015,12:44:48,$HST:Attempting Auto-Start
23.04.2015,12:44:48,$HST:Param. RCU due to START
23.04.2015,12:44:48,$HST:Actual focuscode 02
23.04.2015,12:44:48,$HST:Enable data transfer
23.04.2015,12:44:48,$HST:Receiver calibration
23.04.2015,12:44:48,$CRX:Started
23.04.2015,12:44:49,$HST:Start new FITS-file
23.04.2015,12:44:49,$HST:Continous measurement
23.04.2015,12:44:50,$CRX:e-Callisto ETH Zurich
23.04.2015,12:44:50,$HST:Watchdog triggered -> Reset
23.04.2015,12:44:50,$CRX:V1.5, 2006-11-04
23.04.2015,12:44:51,$CRX:ChargePump=On
23.04.2015,12:44:51,$HST:CD1316LV/IV detected
23.04.2015,12:44:51,$CRX:Debug=Off
23.04.2015,12:44:51,$CRX:Trigger=No
23.04.2015,12:44:51,$CRX:FPUcodex=0
23.04.2015,12:44:51,$CRX:GS =13
23.04.2015,12:44:51,$CRX:GA =253
23.04.2015,12:44:51,$CRX:Delay=0msec
23.04.2015,12:44:51,$CRX:Frequency=0.0MHz
23.04.2015,12:44:51,$HST:Receiver connected
23.04.2015,12:44:51,$CRX:Sweeplength=0
23.04.2015,12:44:51,$CRX:low_band_max=171MHz
23.04.2015,12:44:51,$CRX:mid_band_max=450MHz
23.04.2015,12:44:51,$CRX:high_band_max=863MHz
23.04.2015,12:44:51,$CRX:Idle=0x
23.04.2015,12:44:51,$CRX:ChargePump=On
23.04.2015,12:44:51,$HST:CD1316LV/IV detected
23.04.2015,12:44:51,$CRX:Debug=Off
23.04.2015,12:44:51,$CRX:Trigger=Extern
23.04.2015,12:44:51,$CRX:FPUcodex=0
23.04.2015,12:44:51,$CRX:GS =13
23.04.2015,12:44:51,$CRX:GA =624
23.04.2015,12:44:51,$CRX:Delay=0msec
23.04.2015,12:44:51,$CRX:Frequency=45.0MHz
23.04.2015,12:44:51,$HST:Receiver connected
23.04.2015,12:44:51,$CRX:Sweeplength=200
23.04.2015,12:44:51,$CRX:low_band_max=171MHz
23.04.2015,12:44:51,$CRX:mid_band_max=450MHz
23.04.2015,12:44:51,$CRX:high_band_max=863MHz
23.04.2015,12:44:51,$CRX:Idle=0x
23.04.2015,12:44:53,$HST:Auto stop due to data loss.
23.04.2015,12:44:54,$HST:Measurement stop
23.04.2015,12:44:54,$HST:Measurement wait...
23.04.2015,12:44:55,$HST:Measurement halted
23.04.2015,12:44:55,$HST:Measurement idle
23.04.2015,12:44:55,$CRX:Stopped
23.04.2015,12:44:55,$HST:Measurement enable
23.04.2015,12:44:55,$CRX:AGC gain = 1.57V
23.04.2015,12:44:55,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:44:55,$CRX:Analog Input = 9.24
23.04.2015,12:44:56,$HST:Check RS232-connection!
23.04.2015,12:44:59,$HST:Attempting Auto-Start
23.04.2015,12:45:00,$HST:Param. RCU due to START
23.04.2015,12:45:00,$HST:Actual focuscode 02
23.04.2015,12:45:00,$HST:Enable data transfer
23.04.2015,12:45:00,$HST:Receiver calibration
23.04.2015,12:45:00,$CRX:Started
23.04.2015,12:45:00,$HST:Start new FITS-file
23.04.2015,12:45:00,$HST:Continous measurement
23.04.2015,12:45:02,$CRX:e-Callisto ETH Zurich
23.04.2015,12:45:02,$HST:Watchdog triggered -> Reset
23.04.2015,12:45:02,$CRX:V1.5, 2006-11-04
23.04.2015,12:45:02,$CRX:ChargePump=On
23.04.2015,12:45:02,$HST:CD1316LV/IV detected
23.04.2015,12:45:02,$CRX:Debug=Off
23.04.2015,12:45:02,$CRX:Trigger=No
23.04.2015,12:45:02,$CRX:FPUcodex=0
23.04.2015,12:45:02,$CRX:GS =13
23.04.2015,12:45:02,$CRX:GA =253
23.04.2015,12:45:02,$CRX:Delay=0msec
23.04.2015,12:45:02,$CRX:Frequency=0.0MHz
23.04.2015,12:45:02,$HST:Receiver connected
23.04.2015,12:45:02,$CRX:Sweeplength=0
23.04.2015,12:45:02,$CRX:low_band_max=171MHz
23.04.2015,12:45:02,$CRX:mid_band_max=450MHz
23.04.2015,12:45:02,$CRX:high_band_max=863MHz
23.04.2015,12:45:02,$CRX:Idle=0x
23.04.2015,12:45:02,$CRX:ChargePump=On
23.04.2015,12:45:02,$HST:CD1316LV/IV detected
23.04.2015,12:45:02,$CRX:Debug=Off
23.04.2015,12:45:02,$CRX:Trigger=Extern
23.04.2015,12:45:02,$CRX:FPUcodex=0
23.04.2015,12:45:02,$CRX:GS =13
23.04.2015,12:45:02,$CRX:GA =624
23.04.2015,12:45:02,$CRX:Delay=0msec
23.04.2015,12:45:02,$CRX:Frequency=45.0MHz
23.04.2015,12:45:02,$HST:Receiver connected
23.04.2015,12:45:02,$CRX:Sweeplength=200
23.04.2015,12:45:02,$CRX:low_band_max=171MHz
23.04.2015,12:45:02,$CRX:mid_band_max=450MHz
23.04.2015,12:45:02,$CRX:high_band_max=863MHz
23.04.2015,12:45:02,$CRX:Idle=0x
23.04.2015,12:45:05,$HST:Auto stop due to data loss.
23.04.2015,12:45:05,$HST:Measurement stop
23.04.2015,12:45:05,$HST:Measurement wait...
23.04.2015,12:45:06,$HST:Measurement halted
23.04.2015,12:45:06,$HST:Measurement idle
23.04.2015,12:45:06,$CRX:Stopped
23.04.2015,12:45:06,$HST:Measurement enable
23.04.2015,12:45:06,$CRX:AGC gain = 1.57V
23.04.2015,12:45:06,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:45:06,$CRX:Analog Input = 9.24
23.04.2015,12:45:08,$HST:Check RS232-connection!
23.04.2015,12:45:11,$HST:Attempting Auto-Start
23.04.2015,12:45:11,$HST:Param. RCU due to START
23.04.2015,12:45:11,$HST:Actual focuscode 02
23.04.2015,12:45:11,$HST:Enable data transfer
23.04.2015,12:45:11,$HST:Receiver calibration
23.04.2015,12:45:11,$CRX:Started
23.04.2015,12:45:11,$HST:Start new FITS-file
23.04.2015,12:45:12,$HST:Continous measurement
23.04.2015,12:45:13,$CRX:e-Callisto ETH Zurich
23.04.2015,12:45:13,$HST:Watchdog triggered -> Reset
23.04.2015,12:45:13,$CRX:V1.5, 2006-11-04
23.04.2015,12:45:13,$CRX:ChargePump=On
23.04.2015,12:45:13,$HST:CD1316LV/IV detected
23.04.2015,12:45:13,$CRX:Debug=Off
23.04.2015,12:45:13,$CRX:Trigger=No
23.04.2015,12:45:13,$CRX:FPUcodex=0
23.04.2015,12:45:13,$CRX:GS =13
23.04.2015,12:45:13,$CRX:GA =253
23.04.2015,12:45:13,$CRX:Delay=0msec
23.04.2015,12:45:13,$CRX:Frequency=0.0MHz
23.04.2015,12:45:13,$HST:Receiver connected
23.04.2015,12:45:13,$CRX:Sweeplength=0
23.04.2015,12:45:13,$CRX:low_band_max=171MHz
23.04.2015,12:45:13,$CRX:mid_band_max=450MHz
23.04.2015,12:45:13,$CRX:high_band_max=863MHz
23.04.2015,12:45:13,$CRX:Idle=0x
23.04.2015,12:45:13,$CRX:ChargePump=On
23.04.2015,12:45:13,$HST:CD1316LV/IV detected
23.04.2015,12:45:13,$CRX:Debug=Off
23.04.2015,12:45:13,$CRX:Trigger=Extern
23.04.2015,12:45:13,$CRX:FPUcodex=0
23.04.2015,12:45:13,$CRX:GS =13
23.04.2015,12:45:13,$CRX:GA =624
23.04.2015,12:45:13,$CRX:Delay=0msec
23.04.2015,12:45:13,$CRX:Frequency=45.0MHz
23.04.2015,12:45:13,$HST:Receiver connected
23.04.2015,12:45:13,$CRX:Sweeplength=200
23.04.2015,12:45:13,$CRX:low_band_max=171MHz
23.04.2015,12:45:13,$CRX:mid_band_max=450MHz
23.04.2015,12:45:13,$CRX:high_band_max=863MHz
23.04.2015,12:45:13,$CRX:Idle=0x
23.04.2015,12:45:16,$HST:Auto stop due to data loss.
23.04.2015,12:45:16,$HST:Measurement stop
23.04.2015,12:45:17,$HST:Measurement wait...
23.04.2015,12:45:17,$HST:Measurement halted
23.04.2015,12:45:18,$HST:Measurement idle
23.04.2015,12:45:18,$CRX:Stopped
23.04.2015,12:45:18,$HST:Measurement enable
23.04.2015,12:45:18,$CRX:AGC gain = 1.57V
23.04.2015,12:45:18,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:45:18,$CRX:Analog Input = 9.24
23.04.2015,12:45:19,$HST:Check RS232-connection!
23.04.2015,12:45:22,$HST:Attempting Auto-Start
23.04.2015,12:45:22,$HST:Param. RCU due to START
23.04.2015,12:45:22,$HST:Actual focuscode 02
23.04.2015,12:45:23,$HST:Enable data transfer
23.04.2015,12:45:23,$HST:Receiver calibration
23.04.2015,12:45:23,$CRX:Started
23.04.2015,12:45:23,$HST:Start new FITS-file
23.04.2015,12:45:23,$HST:Continous measurement
23.04.2015,12:45:25,$CRX:e-Callisto ETH Zurich
23.04.2015,12:45:25,$HST:Watchdog triggered -> Reset
23.04.2015,12:45:25,$CRX:V1.5, 2006-11-04
23.04.2015,12:45:25,$CRX:ChargePump=On
23.04.2015,12:45:25,$HST:CD1316LV/IV detected
23.04.2015,12:45:25,$CRX:Debug=Off
23.04.2015,12:45:25,$CRX:Trigger=No
23.04.2015,12:45:25,$CRX:FPUcodex=0
23.04.2015,12:45:25,$CRX:GS =13
23.04.2015,12:45:25,$CRX:GA =253
23.04.2015,12:45:25,$CRX:Delay=0msec
23.04.2015,12:45:25,$CRX:Frequency=0.0MHz
23.04.2015,12:45:25,$HST:Receiver connected
23.04.2015,12:45:25,$CRX:Sweeplength=0
23.04.2015,12:45:25,$CRX:low_band_max=171MHz
23.04.2015,12:45:25,$CRX:mid_band_max=450MHz
23.04.2015,12:45:25,$CRX:high_band_max=863MHz
23.04.2015,12:45:25,$CRX:Idle=0x
23.04.2015,12:45:25,$CRX:ChargePump=On
23.04.2015,12:45:25,$HST:CD1316LV/IV detected
23.04.2015,12:45:25,$CRX:Debug=Off
23.04.2015,12:45:25,$CRX:Trigger=Extern
23.04.2015,12:45:25,$CRX:FPUcodex=0
23.04.2015,12:45:25,$CRX:GS =13
23.04.2015,12:45:25,$CRX:GA =624
23.04.2015,12:45:25,$CRX:Delay=0msec
23.04.2015,12:45:25,$CRX:Frequency=45.0MHz
23.04.2015,12:45:25,$HST:Receiver connected
23.04.2015,12:45:25,$CRX:Sweeplength=200
23.04.2015,12:45:25,$CRX:low_band_max=171MHz
23.04.2015,12:45:25,$CRX:mid_band_max=450MHz
23.04.2015,12:45:25,$CRX:high_band_max=863MHz
23.04.2015,12:45:25,$CRX:Idle=0x
23.04.2015,12:45:28,$HST:Auto stop due to data loss.
23.04.2015,12:45:28,$HST:Measurement stop
23.04.2015,12:45:28,$HST:Measurement wait...
23.04.2015,12:45:29,$HST:Measurement halted
23.04.2015,12:45:29,$HST:Measurement idle
23.04.2015,12:45:29,$CRX:Stopped
23.04.2015,12:45:29,$HST:Measurement enable
23.04.2015,12:45:29,$CRX:AGC gain = 1.57V
23.04.2015,12:45:29,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:45:29,$CRX:Analog Input = 9.24
23.04.2015,12:45:31,$HST:Check RS232-connection!
23.04.2015,12:45:34,$HST:Attempting Auto-Start
23.04.2015,12:45:34,$HST:Param. RCU due to START
23.04.2015,12:45:34,$HST:Actual focuscode 02
23.04.2015,12:45:34,$HST:Enable data transfer
23.04.2015,12:45:34,$HST:Receiver calibration
23.04.2015,12:45:34,$CRX:Started
23.04.2015,12:45:34,$HST:Start new FITS-file
23.04.2015,12:45:34,$HST:Continous measurement
23.04.2015,12:45:36,$CRX:e-Callisto ETH Zurich
23.04.2015,12:45:36,$HST:Watchdog triggered -> Reset
23.04.2015,12:45:36,$CRX:V1.5, 2006-11-04
23.04.2015,12:45:36,$CRX:ChargePump=On
23.04.2015,12:45:36,$HST:CD1316LV/IV detected
23.04.2015,12:45:36,$CRX:Debug=Off
23.04.2015,12:45:36,$CRX:Trigger=No
23.04.2015,12:45:36,$CRX:FPUcodex=0
23.04.2015,12:45:36,$CRX:GS =13
23.04.2015,12:45:36,$CRX:GA =253
23.04.2015,12:45:36,$CRX:Delay=0msec
23.04.2015,12:45:36,$CRX:Frequency=0.0MHz
23.04.2015,12:45:36,$HST:Receiver connected
23.04.2015,12:45:36,$CRX:Sweeplength=0
23.04.2015,12:45:36,$CRX:low_band_max=171MHz
23.04.2015,12:45:36,$CRX:mid_band_max=450MHz
23.04.2015,12:45:36,$CRX:high_band_max=863MHz
23.04.2015,12:45:36,$CRX:Idle=0x
23.04.2015,12:45:36,$CRX:ChargePump=On
23.04.2015,12:45:36,$HST:CD1316LV/IV detected
23.04.2015,12:45:36,$CRX:Debug=Off
23.04.2015,12:45:36,$CRX:Trigger=Extern
23.04.2015,12:45:36,$CRX:FPUcodex=0
23.04.2015,12:45:36,$CRX:GS =13
23.04.2015,12:45:36,$CRX:GA =624
23.04.2015,12:45:36,$CRX:Delay=0msec
23.04.2015,12:45:36,$CRX:Frequency=45.0MHz
23.04.2015,12:45:36,$HST:Receiver connected
23.04.2015,12:45:36,$CRX:Sweeplength=200
23.04.2015,12:45:36,$CRX:low_band_max=171MHz
23.04.2015,12:45:36,$CRX:mid_band_max=450MHz
23.04.2015,12:45:36,$CRX:high_band_max=863MHz
23.04.2015,12:45:36,$CRX:Idle=0x
23.04.2015,12:45:39,$HST:Auto stop due to data loss.
23.04.2015,12:45:39,$HST:Measurement stop
23.04.2015,12:45:40,$HST:Measurement wait...
23.04.2015,12:45:40,$HST:Measurement halted
23.04.2015,12:45:40,$HST:Measurement idle
23.04.2015,12:45:40,$CRX:Stopped
23.04.2015,12:45:41,$HST:Measurement enable
23.04.2015,12:45:41,$CRX:AGC gain = 1.56V
23.04.2015,12:45:41,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:45:41,$CRX:Analog Input = 9.24
23.04.2015,12:45:42,$HST:Check RS232-connection!
23.04.2015,12:45:45,$HST:Attempting Auto-Start
23.04.2015,12:45:45,$HST:Param. RCU due to START
23.04.2015,12:45:45,$HST:Actual focuscode 02
23.04.2015,12:45:45,$HST:Enable data transfer
23.04.2015,12:45:45,$HST:Receiver calibration
23.04.2015,12:45:45,$CRX:Started
23.04.2015,12:45:46,$HST:Start new FITS-file
23.04.2015,12:45:46,$HST:Continous measurement
23.04.2015,12:45:48,$CRX:e-Callisto ETH Zurich
23.04.2015,12:45:48,$HST:Watchdog triggered -> Reset
23.04.2015,12:45:48,$CRX:V1.5, 2006-11-04
23.04.2015,12:45:48,$CRX:ChargePump=On
23.04.2015,12:45:48,$HST:CD1316LV/IV detected
23.04.2015,12:45:48,$CRX:Debug=Off
23.04.2015,12:45:48,$CRX:Trigger=No
23.04.2015,12:45:48,$CRX:FPUcodex=0
23.04.2015,12:45:48,$CRX:GS =13
23.04.2015,12:45:48,$CRX:GA =253
23.04.2015,12:45:48,$CRX:Delay=0msec
23.04.2015,12:45:48,$CRX:Frequency=0.0MHz
23.04.2015,12:45:48,$HST:Receiver connected
23.04.2015,12:45:48,$CRX:Sweeplength=0
23.04.2015,12:45:48,$CRX:low_band_max=171MHz
23.04.2015,12:45:48,$CRX:mid_band_max=450MHz
23.04.2015,12:45:48,$CRX:high_band_max=863MHz
23.04.2015,12:45:48,$CRX:Idle=0x
23.04.2015,12:45:48,$CRX:ChargePump=On
23.04.2015,12:45:48,$HST:CD1316LV/IV detected
23.04.2015,12:45:48,$CRX:Debug=Off
23.04.2015,12:45:48,$CRX:Trigger=Extern
23.04.2015,12:45:48,$CRX:FPUcodex=0
23.04.2015,12:45:48,$CRX:GS =13
23.04.2015,12:45:48,$CRX:GA =624
23.04.2015,12:45:48,$CRX:Delay=0msec
23.04.2015,12:45:48,$CRX:Frequency=45.0MHz
23.04.2015,12:45:48,$HST:Receiver connected
23.04.2015,12:45:48,$CRX:Sweeplength=200
23.04.2015,12:45:48,$CRX:low_band_max=171MHz
23.04.2015,12:45:48,$CRX:mid_band_max=450MHz
23.04.2015,12:45:48,$CRX:high_band_max=863MHz
23.04.2015,12:45:48,$CRX:Idle=0x
23.04.2015,12:45:51,$HST:Auto stop due to data loss.
23.04.2015,12:45:51,$HST:Measurement stop
23.04.2015,12:45:51,$HST:Measurement wait...
23.04.2015,12:45:52,$HST:Measurement halted
23.04.2015,12:45:52,$HST:Measurement idle
23.04.2015,12:45:52,$CRX:Stopped
23.04.2015,12:45:52,$HST:Measurement enable
23.04.2015,12:45:52,$CRX:AGC gain = 1.56V
23.04.2015,12:45:52,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:45:52,$CRX:Analog Input = 9.24
23.04.2015,12:45:54,$HST:Check RS232-connection!
23.04.2015,12:45:57,$HST:Attempting Auto-Start
23.04.2015,12:45:57,$HST:Param. RCU due to START
23.04.2015,12:45:57,$HST:Actual focuscode 02
23.04.2015,12:45:57,$HST:Enable data transfer
23.04.2015,12:45:57,$HST:Receiver calibration
23.04.2015,12:45:57,$CRX:Started
23.04.2015,12:45:57,$HST:Start new FITS-file
23.04.2015,12:45:57,$HST:Continous measurement
23.04.2015,12:45:59,$CRX:e-Callisto ETH Zurich
23.04.2015,12:45:59,$HST:Watchdog triggered -> Reset
23.04.2015,12:45:59,$CRX:V1.5, 2006-11-04
23.04.2015,12:45:59,$CRX:ChargePump=On
23.04.2015,12:45:59,$HST:CD1316LV/IV detected
23.04.2015,12:45:59,$CRX:Debug=Off
23.04.2015,12:45:59,$CRX:Trigger=No
23.04.2015,12:45:59,$CRX:FPUcodex=0
23.04.2015,12:45:59,$CRX:GS =13
23.04.2015,12:45:59,$CRX:GA =253
23.04.2015,12:45:59,$CRX:Delay=0msec
23.04.2015,12:45:59,$CRX:Frequency=0.0MHz
23.04.2015,12:45:59,$HST:Receiver connected
23.04.2015,12:45:59,$CRX:Sweeplength=0
23.04.2015,12:45:59,$CRX:low_band_max=171MHz
23.04.2015,12:45:59,$CRX:mid_band_max=450MHz
23.04.2015,12:45:59,$CRX:high_band_max=863MHz
23.04.2015,12:45:59,$CRX:Idle=0x
23.04.2015,12:45:59,$CRX:ChargePump=On
23.04.2015,12:45:59,$HST:CD1316LV/IV detected
23.04.2015,12:45:59,$CRX:Debug=Off
23.04.2015,12:45:59,$CRX:Trigger=Extern
23.04.2015,12:45:59,$CRX:FPUcodex=0
23.04.2015,12:45:59,$CRX:GS =13
23.04.2015,12:45:59,$CRX:GA =624
23.04.2015,12:45:59,$CRX:Delay=0msec
23.04.2015,12:45:59,$CRX:Frequency=45.0MHz
23.04.2015,12:45:59,$HST:Receiver connected
23.04.2015,12:45:59,$CRX:Sweeplength=200
23.04.2015,12:45:59,$CRX:low_band_max=171MHz
23.04.2015,12:45:59,$CRX:mid_band_max=450MHz
23.04.2015,12:45:59,$CRX:high_band_max=863MHz
23.04.2015,12:45:59,$CRX:Idle=0x
23.04.2015,12:46:02,$HST:Auto stop due to data loss.
23.04.2015,12:46:02,$HST:Measurement stop
23.04.2015,12:46:02,$HST:Measurement wait...
23.04.2015,12:46:03,$HST:Measurement halted
23.04.2015,12:46:03,$HST:Measurement idle
23.04.2015,12:46:03,$CRX:Stopped
23.04.2015,12:46:03,$HST:Measurement enable
23.04.2015,12:46:03,$CRX:AGC gain = 1.57V
23.04.2015,12:46:03,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:46:03,$CRX:Analog Input = 9.24
23.04.2015,12:46:05,$HST:Check RS232-connection!
23.04.2015,12:46:08,$HST:Attempting Auto-Start
23.04.2015,12:46:08,$HST:Param. RCU due to START
23.04.2015,12:46:08,$HST:Actual focuscode 02
23.04.2015,12:46:08,$HST:Enable data transfer
23.04.2015,12:46:08,$HST:Receiver calibration
23.04.2015,12:46:08,$CRX:Started
23.04.2015,12:46:09,$HST:Start new FITS-file
23.04.2015,12:46:09,$HST:Continous measurement
23.04.2015,12:46:10,$CRX:e-Callisto ETH Zurich
23.04.2015,12:46:10,$HST:Watchdog triggered -> Reset
23.04.2015,12:46:10,$CRX:V1.5, 2006-11-04
23.04.2015,12:46:11,$CRX:ChargePump=On
23.04.2015,12:46:11,$HST:CD1316LV/IV detected
23.04.2015,12:46:11,$CRX:Debug=Off
23.04.2015,12:46:11,$CRX:Trigger=No
23.04.2015,12:46:11,$CRX:FPUcodex=0
23.04.2015,12:46:11,$CRX:GS =13
23.04.2015,12:46:11,$CRX:GA =253
23.04.2015,12:46:11,$CRX:Delay=0msec
23.04.2015,12:46:11,$CRX:Frequency=0.0MHz
23.04.2015,12:46:11,$HST:Receiver connected
23.04.2015,12:46:11,$CRX:Sweeplength=0
23.04.2015,12:46:11,$CRX:low_band_max=171MHz
23.04.2015,12:46:11,$CRX:mid_band_max=450MHz
23.04.2015,12:46:11,$CRX:high_band_max=863MHz
23.04.2015,12:46:11,$CRX:Idle=0x
23.04.2015,12:46:11,$CRX:ChargePump=On
23.04.2015,12:46:11,$HST:CD1316LV/IV detected
23.04.2015,12:46:11,$CRX:Debug=Off
23.04.2015,12:46:11,$CRX:Trigger=Extern
23.04.2015,12:46:11,$CRX:FPUcodex=0
23.04.2015,12:46:11,$CRX:GS =13
23.04.2015,12:46:11,$CRX:GA =624
23.04.2015,12:46:11,$CRX:Delay=0msec
23.04.2015,12:46:11,$CRX:Frequency=45.0MHz
23.04.2015,12:46:11,$HST:Receiver connected
23.04.2015,12:46:11,$CRX:Sweeplength=200
23.04.2015,12:46:11,$CRX:low_band_max=171MHz
23.04.2015,12:46:11,$CRX:mid_band_max=450MHz
23.04.2015,12:46:11,$CRX:high_band_max=863MHz
23.04.2015,12:46:11,$CRX:Idle=0x
23.04.2015,12:46:13,$HST:Auto stop due to data loss.
23.04.2015,12:46:14,$HST:Measurement stop
23.04.2015,12:46:14,$HST:Measurement wait...
23.04.2015,12:46:15,$HST:Measurement halted
23.04.2015,12:46:15,$HST:Measurement idle
23.04.2015,12:46:15,$CRX:Stopped
23.04.2015,12:46:15,$HST:Measurement enable
23.04.2015,12:46:15,$CRX:AGC gain = 1.56V
23.04.2015,12:46:15,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:46:15,$CRX:Analog Input = 9.24
23.04.2015,12:46:16,$HST:Check RS232-connection!
23.04.2015,12:46:19,$HST:Attempting Auto-Start
23.04.2015,12:46:20,$HST:Param. RCU due to START
23.04.2015,12:46:20,$HST:Actual focuscode 02
23.04.2015,12:46:20,$HST:Enable data transfer
23.04.2015,12:46:20,$HST:Receiver calibration
23.04.2015,12:46:20,$CRX:Started
23.04.2015,12:46:20,$HST:Start new FITS-file
23.04.2015,12:46:20,$HST:Continous measurement
23.04.2015,12:46:22,$CRX:e-Callisto ETH Zurich
23.04.2015,12:46:22,$HST:Watchdog triggered -> Reset
23.04.2015,12:46:22,$CRX:V1.5, 2006-11-04
23.04.2015,12:46:22,$CRX:ChargePump=On
23.04.2015,12:46:22,$HST:CD1316LV/IV detected
23.04.2015,12:46:22,$CRX:Debug=Off
23.04.2015,12:46:22,$CRX:Trigger=No
23.04.2015,12:46:22,$CRX:FPUcodex=0
23.04.2015,12:46:22,$CRX:GS =13
23.04.2015,12:46:22,$CRX:GA =253
23.04.2015,12:46:22,$CRX:Delay=0msec
23.04.2015,12:46:22,$CRX:Frequency=0.0MHz
23.04.2015,12:46:22,$HST:Receiver connected
23.04.2015,12:46:22,$CRX:Sweeplength=0
23.04.2015,12:46:22,$CRX:low_band_max=171MHz
23.04.2015,12:46:22,$CRX:mid_band_max=450MHz
23.04.2015,12:46:22,$CRX:high_band_max=863MHz
23.04.2015,12:46:22,$CRX:Idle=0x
23.04.2015,12:46:22,$CRX:ChargePump=On
23.04.2015,12:46:22,$HST:CD1316LV/IV detected
23.04.2015,12:46:22,$CRX:Debug=Off
23.04.2015,12:46:22,$CRX:Trigger=Extern
23.04.2015,12:46:22,$CRX:FPUcodex=0
23.04.2015,12:46:22,$CRX:GS =13
23.04.2015,12:46:22,$CRX:GA =624
23.04.2015,12:46:22,$CRX:Delay=0msec
23.04.2015,12:46:22,$CRX:Frequency=45.0MHz
23.04.2015,12:46:22,$HST:Receiver connected
23.04.2015,12:46:22,$CRX:Sweeplength=200
23.04.2015,12:46:22,$CRX:low_band_max=171MHz
23.04.2015,12:46:22,$CRX:mid_band_max=450MHz
23.04.2015,12:46:22,$CRX:high_band_max=863MHz
23.04.2015,12:46:22,$CRX:Idle=0x
23.04.2015,12:46:25,$HST:Auto stop due to data loss.
23.04.2015,12:46:25,$HST:Measurement stop
23.04.2015,12:46:25,$HST:Measurement wait...
23.04.2015,12:46:26,$HST:Measurement halted
23.04.2015,12:46:26,$HST:Measurement idle
23.04.2015,12:46:26,$CRX:Stopped
23.04.2015,12:46:26,$HST:Measurement enable
23.04.2015,12:46:26,$CRX:AGC gain = 1.57V
23.04.2015,12:46:26,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:46:26,$CRX:Analog Input = 9.24
23.04.2015,12:46:28,$HST:Check RS232-connection!
23.04.2015,12:46:31,$HST:Attempting Auto-Start
23.04.2015,12:46:31,$HST:Param. RCU due to START
23.04.2015,12:46:31,$HST:Actual focuscode 02
23.04.2015,12:46:31,$HST:Enable data transfer
23.04.2015,12:46:31,$HST:Receiver calibration
23.04.2015,12:46:31,$CRX:Started
23.04.2015,12:46:31,$HST:Start new FITS-file
23.04.2015,12:46:32,$HST:Continous measurement
23.04.2015,12:46:33,$CRX:e-Callisto ETH Zurich
23.04.2015,12:46:33,$HST:Watchdog triggered -> Reset
23.04.2015,12:46:33,$CRX:V1.5, 2006-11-04
23.04.2015,12:46:33,$CRX:ChargePump=On
23.04.2015,12:46:33,$HST:CD1316LV/IV detected
23.04.2015,12:46:33,$CRX:Debug=Off
23.04.2015,12:46:33,$CRX:Trigger=No
23.04.2015,12:46:33,$CRX:FPUcodex=0
23.04.2015,12:46:33,$CRX:GS =13
23.04.2015,12:46:33,$CRX:GA =253
23.04.2015,12:46:33,$CRX:Delay=0msec
23.04.2015,12:46:33,$CRX:Frequency=0.0MHz
23.04.2015,12:46:33,$HST:Receiver connected
23.04.2015,12:46:33,$CRX:Sweeplength=0
23.04.2015,12:46:33,$CRX:low_band_max=171MHz
23.04.2015,12:46:33,$CRX:mid_band_max=450MHz
23.04.2015,12:46:33,$CRX:high_band_max=863MHz
23.04.2015,12:46:33,$CRX:Idle=0x
23.04.2015,12:46:33,$CRX:ChargePump=On
23.04.2015,12:46:33,$HST:CD1316LV/IV detected
23.04.2015,12:46:33,$CRX:Debug=Off
23.04.2015,12:46:33,$CRX:Trigger=Extern
23.04.2015,12:46:33,$CRX:FPUcodex=0
23.04.2015,12:46:33,$CRX:GS =13
23.04.2015,12:46:33,$CRX:GA =624
23.04.2015,12:46:33,$CRX:Delay=0msec
23.04.2015,12:46:33,$CRX:Frequency=45.0MHz
23.04.2015,12:46:33,$HST:Receiver connected
23.04.2015,12:46:33,$CRX:Sweeplength=200
23.04.2015,12:46:33,$CRX:low_band_max=171MHz
23.04.2015,12:46:33,$CRX:mid_band_max=450MHz
23.04.2015,12:46:33,$CRX:high_band_max=863MHz
23.04.2015,12:46:33,$CRX:Idle=0x
23.04.2015,12:46:36,$HST:Auto stop due to data loss.
23.04.2015,12:46:36,$HST:Measurement stop
23.04.2015,12:46:37,$HST:Measurement wait...
23.04.2015,12:46:37,$HST:Measurement halted
23.04.2015,12:46:38,$HST:Measurement idle
23.04.2015,12:46:38,$CRX:Stopped
23.04.2015,12:46:38,$HST:Measurement enable
23.04.2015,12:46:38,$CRX:AGC gain = 1.57V
23.04.2015,12:46:38,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:46:38,$CRX:Analog Input = 9.24
23.04.2015,12:46:39,$HST:Check RS232-connection!
23.04.2015,12:46:42,$HST:Attempting Auto-Start
23.04.2015,12:46:42,$HST:Param. RCU due to START
23.04.2015,12:46:42,$HST:Actual focuscode 02
23.04.2015,12:46:43,$HST:Enable data transfer
23.04.2015,12:46:43,$HST:Receiver calibration
23.04.2015,12:46:43,$CRX:Started
23.04.2015,12:46:43,$HST:Start new FITS-file
23.04.2015,12:46:43,$HST:Continous measurement
23.04.2015,12:46:45,$CRX:e-Callisto ETH Zurich
23.04.2015,12:46:45,$HST:Watchdog triggered -> Reset
23.04.2015,12:46:45,$CRX:V1.5, 2006-11-04
23.04.2015,12:46:45,$CRX:ChargePump=On
23.04.2015,12:46:45,$HST:CD1316LV/IV detected
23.04.2015,12:46:45,$CRX:Debug=Off
23.04.2015,12:46:45,$CRX:Trigger=No
23.04.2015,12:46:45,$CRX:FPUcodex=0
23.04.2015,12:46:45,$CRX:GS =13
23.04.2015,12:46:45,$CRX:GA =253
23.04.2015,12:46:45,$CRX:Delay=0msec
23.04.2015,12:46:45,$CRX:Frequency=0.0MHz
23.04.2015,12:46:45,$HST:Receiver connected
23.04.2015,12:46:45,$CRX:Sweeplength=0
23.04.2015,12:46:45,$CRX:low_band_max=171MHz
23.04.2015,12:46:45,$CRX:mid_band_max=450MHz
23.04.2015,12:46:45,$CRX:high_band_max=863MHz
23.04.2015,12:46:45,$CRX:Idle=0x
23.04.2015,12:46:45,$CRX:ChargePump=On
23.04.2015,12:46:45,$HST:CD1316LV/IV detected
23.04.2015,12:46:45,$CRX:Debug=Off
23.04.2015,12:46:45,$CRX:Trigger=Extern
23.04.2015,12:46:45,$CRX:FPUcodex=0
23.04.2015,12:46:45,$CRX:GS =13
23.04.2015,12:46:45,$CRX:GA =624
23.04.2015,12:46:45,$CRX:Delay=0msec
23.04.2015,12:46:45,$CRX:Frequency=45.0MHz
23.04.2015,12:46:45,$HST:Receiver connected
23.04.2015,12:46:45,$CRX:Sweeplength=200
23.04.2015,12:46:45,$CRX:low_band_max=171MHz
23.04.2015,12:46:45,$CRX:mid_band_max=450MHz
23.04.2015,12:46:45,$CRX:high_band_max=863MHz
23.04.2015,12:46:45,$CRX:Idle=0x
23.04.2015,12:46:48,$HST:Auto stop due to data loss.
23.04.2015,12:46:48,$HST:Measurement stop
23.04.2015,12:46:48,$HST:Measurement wait...
23.04.2015,12:46:49,$HST:Measurement halted
23.04.2015,12:46:49,$HST:Measurement idle
23.04.2015,12:46:49,$CRX:Stopped
23.04.2015,12:46:49,$HST:Measurement enable
23.04.2015,12:46:49,$CRX:AGC gain = 1.57V
23.04.2015,12:46:49,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:46:49,$CRX:Analog Input = 9.24
23.04.2015,12:46:51,$HST:Check RS232-connection!
23.04.2015,12:46:54,$HST:Attempting Auto-Start
23.04.2015,12:46:54,$HST:Param. RCU due to START
23.04.2015,12:46:54,$HST:Actual focuscode 02
23.04.2015,12:46:54,$HST:Enable data transfer
23.04.2015,12:46:54,$HST:Receiver calibration
23.04.2015,12:46:54,$CRX:Started
23.04.2015,12:46:54,$HST:Start new FITS-file
23.04.2015,12:46:54,$HST:Continous measurement
23.04.2015,12:46:56,$CRX:e-Callisto ETH Zurich
23.04.2015,12:46:56,$HST:Watchdog triggered -> Reset
23.04.2015,12:46:56,$CRX:V1.5, 2006-11-04
23.04.2015,12:46:56,$CRX:ChargePump=On
23.04.2015,12:46:56,$HST:CD1316LV/IV detected
23.04.2015,12:46:56,$CRX:Debug=Off
23.04.2015,12:46:56,$CRX:Trigger=No
23.04.2015,12:46:56,$CRX:FPUcodex=0
23.04.2015,12:46:56,$CRX:GS =13
23.04.2015,12:46:56,$CRX:GA =253
23.04.2015,12:46:56,$CRX:Delay=0msec
23.04.2015,12:46:56,$CRX:Frequency=0.0MHz
23.04.2015,12:46:56,$HST:Receiver connected
23.04.2015,12:46:56,$CRX:Sweeplength=0
23.04.2015,12:46:56,$CRX:low_band_max=171MHz
23.04.2015,12:46:56,$CRX:mid_band_max=450MHz
23.04.2015,12:46:56,$CRX:high_band_max=863MHz
23.04.2015,12:46:56,$CRX:Idle=0x
23.04.2015,12:46:56,$CRX:ChargePump=On
23.04.2015,12:46:56,$HST:CD1316LV/IV detected
23.04.2015,12:46:56,$CRX:Debug=Off
23.04.2015,12:46:56,$CRX:Trigger=Extern
23.04.2015,12:46:56,$CRX:FPUcodex=0
23.04.2015,12:46:56,$CRX:GS =13
23.04.2015,12:46:56,$CRX:GA =624
23.04.2015,12:46:56,$CRX:Delay=0msec
23.04.2015,12:46:56,$CRX:Frequency=45.0MHz
23.04.2015,12:46:56,$HST:Receiver connected
23.04.2015,12:46:56,$CRX:Sweeplength=200
23.04.2015,12:46:56,$CRX:low_band_max=171MHz
23.04.2015,12:46:56,$CRX:mid_band_max=450MHz
23.04.2015,12:46:56,$CRX:high_band_max=863MHz
23.04.2015,12:46:56,$CRX:Idle=0x
23.04.2015,12:46:59,$HST:Auto stop due to data loss.
23.04.2015,12:46:59,$HST:Measurement stop
23.04.2015,12:46:59,$HST:Measurement wait...
23.04.2015,12:47:00,$HST:Measurement halted
23.04.2015,12:47:00,$HST:Measurement idle
23.04.2015,12:47:00,$CRX:Stopped
23.04.2015,12:47:01,$HST:Measurement enable
23.04.2015,12:47:01,$CRX:AGC gain = 1.57V
23.04.2015,12:47:01,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:47:01,$CRX:Analog Input = 9.24
23.04.2015,12:47:02,$HST:Check RS232-connection!
23.04.2015,12:47:05,$HST:Attempting Auto-Start
23.04.2015,12:47:05,$HST:Param. RCU due to START
23.04.2015,12:47:05,$HST:Actual focuscode 02
23.04.2015,12:47:05,$HST:Enable data transfer
23.04.2015,12:47:05,$HST:Receiver calibration
23.04.2015,12:47:05,$CRX:Started
23.04.2015,12:47:06,$HST:Start new FITS-file
23.04.2015,12:47:06,$HST:Continous measurement
23.04.2015,12:47:07,$CRX:e-Callisto ETH Zurich
23.04.2015,12:47:07,$HST:Watchdog triggered -> Reset
23.04.2015,12:47:07,$CRX:V1.5, 2006-11-04
23.04.2015,12:47:08,$CRX:ChargePump=On
23.04.2015,12:47:08,$HST:CD1316LV/IV detected
23.04.2015,12:47:08,$CRX:Debug=Off
23.04.2015,12:47:08,$CRX:Trigger=No
23.04.2015,12:47:08,$CRX:FPUcodex=0
23.04.2015,12:47:08,$CRX:GS =13
23.04.2015,12:47:08,$CRX:GA =253
23.04.2015,12:47:08,$CRX:Delay=0msec
23.04.2015,12:47:08,$CRX:Frequency=0.0MHz
23.04.2015,12:47:08,$HST:Receiver connected
23.04.2015,12:47:08,$CRX:Sweeplength=0
23.04.2015,12:47:08,$CRX:low_band_max=171MHz
23.04.2015,12:47:08,$CRX:mid_band_max=450MHz
23.04.2015,12:47:08,$CRX:high_band_max=863MHz
23.04.2015,12:47:08,$CRX:Idle=0x
23.04.2015,12:47:08,$CRX:ChargePump=On
23.04.2015,12:47:08,$HST:CD1316LV/IV detected
23.04.2015,12:47:08,$CRX:Debug=Off
23.04.2015,12:47:08,$CRX:Trigger=Extern
23.04.2015,12:47:08,$CRX:FPUcodex=0
23.04.2015,12:47:08,$CRX:GS =13
23.04.2015,12:47:08,$CRX:GA =624
23.04.2015,12:47:08,$CRX:Delay=0msec
23.04.2015,12:47:08,$CRX:Frequency=45.0MHz
23.04.2015,12:47:08,$HST:Receiver connected
23.04.2015,12:47:08,$CRX:Sweeplength=200
23.04.2015,12:47:08,$CRX:low_band_max=171MHz
23.04.2015,12:47:08,$CRX:mid_band_max=450MHz
23.04.2015,12:47:08,$CRX:high_band_max=863MHz
23.04.2015,12:47:08,$CRX:Idle=0x
23.04.2015,12:47:10,$HST:Auto stop due to data loss.
23.04.2015,12:47:11,$HST:Measurement stop
23.04.2015,12:47:11,$HST:Measurement wait...
23.04.2015,12:47:12,$HST:Measurement halted
23.04.2015,12:47:12,$HST:Measurement idle
23.04.2015,12:47:12,$CRX:Stopped
23.04.2015,12:47:12,$HST:Measurement enable
23.04.2015,12:47:12,$CRX:AGC gain = 1.57V
23.04.2015,12:47:12,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:47:12,$CRX:Analog Input = 9.24
23.04.2015,12:47:13,$HST:Check RS232-connection!
23.04.2015,12:47:16,$HST:Attempting Auto-Start
23.04.2015,12:47:17,$HST:Param. RCU due to START
23.04.2015,12:47:17,$HST:Actual focuscode 02
23.04.2015,12:47:17,$HST:Enable data transfer
23.04.2015,12:47:17,$HST:Receiver calibration
23.04.2015,12:47:17,$CRX:Started
23.04.2015,12:47:17,$HST:Start new FITS-file
23.04.2015,12:47:17,$HST:Continous measurement
23.04.2015,12:47:19,$CRX:e-Callisto ETH Zurich
23.04.2015,12:47:19,$HST:Watchdog triggered -> Reset
23.04.2015,12:47:19,$CRX:V1.5, 2006-11-04
23.04.2015,12:47:19,$CRX:ChargePump=On
23.04.2015,12:47:19,$HST:CD1316LV/IV detected
23.04.2015,12:47:19,$CRX:Debug=Off
23.04.2015,12:47:19,$CRX:Trigger=No
23.04.2015,12:47:19,$CRX:FPUcodex=0
23.04.2015,12:47:19,$CRX:GS =13
23.04.2015,12:47:19,$CRX:GA =253
23.04.2015,12:47:19,$CRX:Delay=0msec
23.04.2015,12:47:19,$CRX:Frequency=0.0MHz
23.04.2015,12:47:19,$HST:Receiver connected
23.04.2015,12:47:19,$CRX:Sweeplength=0
23.04.2015,12:47:19,$CRX:low_band_max=171MHz
23.04.2015,12:47:19,$CRX:mid_band_max=450MHz
23.04.2015,12:47:19,$CRX:high_band_max=863MHz
23.04.2015,12:47:19,$CRX:Idle=0x
23.04.2015,12:47:19,$CRX:ChargePump=On
23.04.2015,12:47:19,$HST:CD1316LV/IV detected
23.04.2015,12:47:19,$CRX:Debug=Off
23.04.2015,12:47:19,$CRX:Trigger=Extern
23.04.2015,12:47:19,$CRX:FPUcodex=0
23.04.2015,12:47:19,$CRX:GS =13
23.04.2015,12:47:19,$CRX:GA =624
23.04.2015,12:47:19,$CRX:Delay=0msec
23.04.2015,12:47:19,$CRX:Frequency=45.0MHz
23.04.2015,12:47:19,$HST:Receiver connected
23.04.2015,12:47:19,$CRX:Sweeplength=200
23.04.2015,12:47:19,$CRX:low_band_max=171MHz
23.04.2015,12:47:19,$CRX:mid_band_max=450MHz
23.04.2015,12:47:19,$CRX:high_band_max=863MHz
23.04.2015,12:47:19,$CRX:Idle=0x
23.04.2015,12:47:22,$HST:Auto stop due to data loss.
23.04.2015,12:47:22,$HST:Measurement stop
23.04.2015,12:47:22,$HST:Measurement wait...
23.04.2015,12:47:23,$HST:Measurement halted
23.04.2015,12:47:23,$HST:Measurement idle
23.04.2015,12:47:23,$CRX:Stopped
23.04.2015,12:47:23,$HST:Measurement enable
23.04.2015,12:47:23,$CRX:AGC gain = 1.57V
23.04.2015,12:47:23,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:47:23,$CRX:Analog Input = 9.24
23.04.2015,12:47:25,$HST:Check RS232-connection!
23.04.2015,12:47:28,$HST:Attempting Auto-Start
23.04.2015,12:47:28,$HST:Param. RCU due to START
23.04.2015,12:47:28,$HST:Actual focuscode 02
23.04.2015,12:47:28,$HST:Enable data transfer
23.04.2015,12:47:28,$HST:Receiver calibration
23.04.2015,12:47:28,$CRX:Started
23.04.2015,12:47:28,$HST:Start new FITS-file
23.04.2015,12:47:29,$HST:Continous measurement
23.04.2015,12:47:30,$CRX:e-Callisto ETH Zurich
23.04.2015,12:47:30,$HST:Watchdog triggered -> Reset
23.04.2015,12:47:30,$CRX:V1.5, 2006-11-04
23.04.2015,12:47:31,$CRX:ChargePump=On
23.04.2015,12:47:31,$HST:CD1316LV/IV detected
23.04.2015,12:47:31,$CRX:Debug=Off
23.04.2015,12:47:31,$CRX:Trigger=No
23.04.2015,12:47:31,$CRX:FPUcodex=0
23.04.2015,12:47:31,$CRX:GS =13
23.04.2015,12:47:31,$CRX:GA =253
23.04.2015,12:47:31,$CRX:Delay=0msec
23.04.2015,12:47:31,$CRX:Frequency=0.0MHz
23.04.2015,12:47:31,$HST:Receiver connected
23.04.2015,12:47:31,$CRX:Sweeplength=0
23.04.2015,12:47:31,$CRX:low_band_max=171MHz
23.04.2015,12:47:31,$CRX:mid_band_max=450MHz
23.04.2015,12:47:31,$CRX:high_band_max=863MHz
23.04.2015,12:47:31,$CRX:Idle=0x
23.04.2015,12:47:31,$CRX:ChargePump=On
23.04.2015,12:47:31,$HST:CD1316LV/IV detected
23.04.2015,12:47:31,$CRX:Debug=Off
23.04.2015,12:47:31,$CRX:Trigger=Extern
23.04.2015,12:47:31,$CRX:FPUcodex=0
23.04.2015,12:47:31,$CRX:GS =13
23.04.2015,12:47:31,$CRX:GA =624
23.04.2015,12:47:31,$CRX:Delay=0msec
23.04.2015,12:47:31,$CRX:Frequency=45.0MHz
23.04.2015,12:47:31,$HST:Receiver connected
23.04.2015,12:47:31,$CRX:Sweeplength=200
23.04.2015,12:47:31,$CRX:low_band_max=171MHz
23.04.2015,12:47:31,$CRX:mid_band_max=450MHz
23.04.2015,12:47:31,$CRX:high_band_max=863MHz
23.04.2015,12:47:31,$CRX:Idle=0x
23.04.2015,12:47:33,$HST:Auto stop due to data loss.
23.04.2015,12:47:34,$HST:Measurement stop
23.04.2015,12:47:34,$HST:Measurement wait...
23.04.2015,12:47:34,$HST:Measurement halted
23.04.2015,12:47:35,$HST:Measurement idle
23.04.2015,12:47:35,$CRX:Stopped
23.04.2015,12:47:35,$HST:Measurement enable
23.04.2015,12:47:35,$CRX:AGC gain = 1.57V
23.04.2015,12:47:35,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:47:35,$CRX:Analog Input = 9.24
23.04.2015,12:47:36,$HST:Check RS232-connection!
23.04.2015,12:47:39,$HST:Attempting Auto-Start
23.04.2015,12:47:40,$HST:Param. RCU due to START
23.04.2015,12:47:40,$HST:Actual focuscode 02
23.04.2015,12:47:40,$HST:Enable data transfer
23.04.2015,12:47:40,$HST:Receiver calibration
23.04.2015,12:47:40,$CRX:Started
23.04.2015,12:47:40,$HST:Start new FITS-file
23.04.2015,12:47:40,$HST:Continous measurement
23.04.2015,12:47:42,$CRX:e-Callisto ETH Zurich
23.04.2015,12:47:42,$HST:Watchdog triggered -> Reset
23.04.2015,12:47:42,$CRX:V1.5, 2006-11-04
23.04.2015,12:47:42,$CRX:ChargePump=On
23.04.2015,12:47:42,$HST:CD1316LV/IV detected
23.04.2015,12:47:42,$CRX:Debug=Off
23.04.2015,12:47:42,$CRX:Trigger=No
23.04.2015,12:47:42,$CRX:FPUcodex=0
23.04.2015,12:47:42,$CRX:GS =13
23.04.2015,12:47:42,$CRX:GA =253
23.04.2015,12:47:42,$CRX:Delay=0msec
23.04.2015,12:47:42,$CRX:Frequency=0.0MHz
23.04.2015,12:47:42,$HST:Receiver connected
23.04.2015,12:47:42,$CRX:Sweeplength=0
23.04.2015,12:47:42,$CRX:low_band_max=171MHz
23.04.2015,12:47:42,$CRX:mid_band_max=450MHz
23.04.2015,12:47:42,$CRX:high_band_max=863MHz
23.04.2015,12:47:42,$CRX:Idle=0x
23.04.2015,12:47:42,$CRX:ChargePump=On
23.04.2015,12:47:42,$HST:CD1316LV/IV detected
23.04.2015,12:47:42,$CRX:Debug=Off
23.04.2015,12:47:42,$CRX:Trigger=Extern
23.04.2015,12:47:42,$CRX:FPUcodex=0
23.04.2015,12:47:42,$CRX:GS =13
23.04.2015,12:47:42,$CRX:GA =624
23.04.2015,12:47:42,$CRX:Delay=0msec
23.04.2015,12:47:42,$CRX:Frequency=45.0MHz
23.04.2015,12:47:42,$HST:Receiver connected
23.04.2015,12:47:42,$CRX:Sweeplength=200
23.04.2015,12:47:42,$CRX:low_band_max=171MHz
23.04.2015,12:47:42,$CRX:mid_band_max=450MHz
23.04.2015,12:47:42,$CRX:high_band_max=863MHz
23.04.2015,12:47:42,$CRX:Idle=0x
23.04.2015,12:47:45,$HST:Auto stop due to data loss.
23.04.2015,12:47:45,$HST:Measurement stop
23.04.2015,12:47:45,$HST:Measurement wait...
23.04.2015,12:47:46,$HST:Measurement halted
23.04.2015,12:47:46,$HST:Measurement idle
23.04.2015,12:47:46,$CRX:Stopped
23.04.2015,12:47:46,$HST:Measurement enable
23.04.2015,12:47:46,$CRX:AGC gain = 1.57V
23.04.2015,12:47:46,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:47:46,$CRX:Analog Input = 9.24
23.04.2015,12:47:48,$HST:Check RS232-connection!
23.04.2015,12:47:51,$HST:Attempting Auto-Start
23.04.2015,12:47:51,$HST:Param. RCU due to START
23.04.2015,12:47:51,$HST:Actual focuscode 02
23.04.2015,12:47:51,$HST:Enable data transfer
23.04.2015,12:47:51,$HST:Receiver calibration
23.04.2015,12:47:51,$CRX:Started
23.04.2015,12:47:51,$HST:Start new FITS-file
23.04.2015,12:47:51,$HST:Continous measurement
23.04.2015,12:47:53,$CRX:e-Callisto ETH Zurich
23.04.2015,12:47:53,$HST:Watchdog triggered -> Reset
23.04.2015,12:47:53,$CRX:V1.5, 2006-11-04
23.04.2015,12:47:53,$CRX:ChargePump=On
23.04.2015,12:47:53,$HST:CD1316LV/IV detected
23.04.2015,12:47:53,$CRX:Debug=Off
23.04.2015,12:47:53,$CRX:Trigger=No
23.04.2015,12:47:53,$CRX:FPUcodex=0
23.04.2015,12:47:53,$CRX:GS =13
23.04.2015,12:47:53,$CRX:GA =253
23.04.2015,12:47:53,$CRX:Delay=0msec
23.04.2015,12:47:53,$CRX:Frequency=0.0MHz
23.04.2015,12:47:53,$HST:Receiver connected
23.04.2015,12:47:53,$CRX:Sweeplength=0
23.04.2015,12:47:53,$CRX:low_band_max=171MHz
23.04.2015,12:47:53,$CRX:mid_band_max=450MHz
23.04.2015,12:47:53,$CRX:high_band_max=863MHz
23.04.2015,12:47:53,$CRX:Idle=0x
23.04.2015,12:47:53,$CRX:ChargePump=On
23.04.2015,12:47:53,$HST:CD1316LV/IV detected
23.04.2015,12:47:53,$CRX:Debug=Off
23.04.2015,12:47:53,$CRX:Trigger=Extern
23.04.2015,12:47:53,$CRX:FPUcodex=0
23.04.2015,12:47:53,$CRX:GS =13
23.04.2015,12:47:53,$CRX:GA =624
23.04.2015,12:47:53,$CRX:Delay=0msec
23.04.2015,12:47:53,$CRX:Frequency=45.0MHz
23.04.2015,12:47:53,$HST:Receiver connected
23.04.2015,12:47:53,$CRX:Sweeplength=200
23.04.2015,12:47:53,$CRX:low_band_max=171MHz
23.04.2015,12:47:53,$CRX:mid_band_max=450MHz
23.04.2015,12:47:53,$CRX:high_band_max=863MHz
23.04.2015,12:47:53,$CRX:Idle=0x
23.04.2015,12:47:56,$HST:Auto stop due to data loss.
23.04.2015,12:47:56,$HST:Measurement stop
23.04.2015,12:47:57,$HST:Measurement wait...
23.04.2015,12:47:57,$HST:Measurement halted
23.04.2015,12:47:57,$HST:Measurement idle
23.04.2015,12:47:57,$CRX:Stopped
23.04.2015,12:47:58,$HST:Measurement enable
23.04.2015,12:47:58,$CRX:AGC gain = 1.56V
23.04.2015,12:47:58,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:47:58,$CRX:Analog Input = 9.24
23.04.2015,12:47:59,$HST:Check RS232-connection!
23.04.2015,12:48:02,$HST:Attempting Auto-Start
23.04.2015,12:48:02,$HST:Param. RCU due to START
23.04.2015,12:48:02,$HST:Actual focuscode 02
23.04.2015,12:48:03,$HST:Enable data transfer
23.04.2015,12:48:03,$HST:Receiver calibration
23.04.2015,12:48:03,$CRX:Started
23.04.2015,12:48:03,$HST:Start new FITS-file
23.04.2015,12:48:03,$HST:Continous measurement
23.04.2015,12:48:05,$CRX:e-Callisto ETH Zurich
23.04.2015,12:48:05,$HST:Watchdog triggered -> Reset
23.04.2015,12:48:05,$CRX:V1.5, 2006-11-04
23.04.2015,12:48:05,$CRX:ChargePump=On
23.04.2015,12:48:05,$HST:CD1316LV/IV detected
23.04.2015,12:48:05,$CRX:Debug=Off
23.04.2015,12:48:05,$CRX:Trigger=No
23.04.2015,12:48:05,$CRX:FPUcodex=0
23.04.2015,12:48:05,$CRX:GS =13
23.04.2015,12:48:05,$CRX:GA =253
23.04.2015,12:48:05,$CRX:Delay=0msec
23.04.2015,12:48:05,$CRX:Frequency=0.0MHz
23.04.2015,12:48:05,$HST:Receiver connected
23.04.2015,12:48:05,$CRX:Sweeplength=0
23.04.2015,12:48:05,$CRX:low_band_max=171MHz
23.04.2015,12:48:05,$CRX:mid_band_max=450MHz
23.04.2015,12:48:05,$CRX:high_band_max=863MHz
23.04.2015,12:48:05,$CRX:Idle=0x
23.04.2015,12:48:05,$CRX:ChargePump=On
23.04.2015,12:48:05,$HST:CD1316LV/IV detected
23.04.2015,12:48:05,$CRX:Debug=Off
23.04.2015,12:48:05,$CRX:Trigger=Extern
23.04.2015,12:48:05,$CRX:FPUcodex=0
23.04.2015,12:48:05,$CRX:GS =13
23.04.2015,12:48:05,$CRX:GA =624
23.04.2015,12:48:05,$CRX:Delay=0msec
23.04.2015,12:48:05,$CRX:Frequency=45.0MHz
23.04.2015,12:48:05,$HST:Receiver connected
23.04.2015,12:48:05,$CRX:Sweeplength=200
23.04.2015,12:48:05,$CRX:low_band_max=171MHz
23.04.2015,12:48:05,$CRX:mid_band_max=450MHz
23.04.2015,12:48:05,$CRX:high_band_max=863MHz
23.04.2015,12:48:05,$CRX:Idle=0x
23.04.2015,12:48:08,$HST:Auto stop due to data loss.
23.04.2015,12:48:08,$HST:Measurement stop
23.04.2015,12:48:08,$HST:Measurement wait...
23.04.2015,12:48:09,$HST:Measurement halted
23.04.2015,12:48:09,$HST:Measurement idle
23.04.2015,12:48:09,$CRX:Stopped
23.04.2015,12:48:09,$HST:Measurement enable
23.04.2015,12:48:09,$CRX:AGC gain = 1.57V
23.04.2015,12:48:09,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:48:09,$CRX:Analog Input = 9.24
23.04.2015,12:48:11,$HST:Check RS232-connection!
23.04.2015,12:48:14,$HST:Attempting Auto-Start
23.04.2015,12:48:14,$HST:Param. RCU due to START
23.04.2015,12:48:14,$HST:Actual focuscode 02
23.04.2015,12:48:14,$HST:Enable data transfer
23.04.2015,12:48:14,$HST:Receiver calibration
23.04.2015,12:48:14,$CRX:Started
23.04.2015,12:48:14,$HST:Start new FITS-file
23.04.2015,12:48:14,$HST:Continous measurement
23.04.2015,12:48:16,$CRX:e-Callisto ETH Zurich
23.04.2015,12:48:16,$HST:Watchdog triggered -> Reset
23.04.2015,12:48:16,$CRX:V1.5, 2006-11-04
23.04.2015,12:48:16,$CRX:ChargePump=On
23.04.2015,12:48:16,$HST:CD1316LV/IV detected
23.04.2015,12:48:16,$CRX:Debug=Off
23.04.2015,12:48:16,$CRX:Trigger=No
23.04.2015,12:48:16,$CRX:FPUcodex=0
23.04.2015,12:48:16,$CRX:GS =13
23.04.2015,12:48:16,$CRX:GA =253
23.04.2015,12:48:16,$CRX:Delay=0msec
23.04.2015,12:48:16,$CRX:Frequency=0.0MHz
23.04.2015,12:48:16,$HST:Receiver connected
23.04.2015,12:48:16,$CRX:Sweeplength=0
23.04.2015,12:48:16,$CRX:low_band_max=171MHz
23.04.2015,12:48:16,$CRX:mid_band_max=450MHz
23.04.2015,12:48:16,$CRX:high_band_max=863MHz
23.04.2015,12:48:16,$CRX:Idle=0x
23.04.2015,12:48:16,$CRX:ChargePump=On
23.04.2015,12:48:16,$HST:CD1316LV/IV detected
23.04.2015,12:48:16,$CRX:Debug=Off
23.04.2015,12:48:16,$CRX:Trigger=Extern
23.04.2015,12:48:16,$CRX:FPUcodex=0
23.04.2015,12:48:16,$CRX:GS =13
23.04.2015,12:48:16,$CRX:GA =624
23.04.2015,12:48:16,$CRX:Delay=0msec
23.04.2015,12:48:16,$CRX:Frequency=45.0MHz
23.04.2015,12:48:16,$HST:Receiver connected
23.04.2015,12:48:16,$CRX:Sweeplength=200
23.04.2015,12:48:16,$CRX:low_band_max=171MHz
23.04.2015,12:48:16,$CRX:mid_band_max=450MHz
23.04.2015,12:48:16,$CRX:high_band_max=863MHz
23.04.2015,12:48:16,$CRX:Idle=0x
23.04.2015,12:48:19,$HST:Auto stop due to data loss.
23.04.2015,12:48:19,$HST:Measurement stop
23.04.2015,12:48:19,$HST:Measurement wait...
23.04.2015,12:48:20,$HST:Measurement halted
23.04.2015,12:48:20,$HST:Measurement idle
23.04.2015,12:48:20,$CRX:Stopped
23.04.2015,12:48:20,$HST:Measurement enable
23.04.2015,12:48:20,$CRX:AGC gain = 1.56V
23.04.2015,12:48:20,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:48:20,$CRX:Analog Input = 9.24
23.04.2015,12:48:22,$HST:Check RS232-connection!
23.04.2015,12:48:25,$HST:Attempting Auto-Start
23.04.2015,12:48:25,$HST:Param. RCU due to START
23.04.2015,12:48:25,$HST:Actual focuscode 02
23.04.2015,12:48:25,$HST:Enable data transfer
23.04.2015,12:48:25,$HST:Receiver calibration
23.04.2015,12:48:25,$CRX:Started
23.04.2015,12:48:26,$HST:Start new FITS-file
23.04.2015,12:48:26,$HST:Continous measurement
23.04.2015,12:48:27,$CRX:e-Callisto ETH Zurich
23.04.2015,12:48:27,$HST:Watchdog triggered -> Reset
23.04.2015,12:48:27,$CRX:V1.5, 2006-11-04
23.04.2015,12:48:28,$CRX:ChargePump=On
23.04.2015,12:48:28,$HST:CD1316LV/IV detected
23.04.2015,12:48:28,$CRX:Debug=Off
23.04.2015,12:48:28,$CRX:Trigger=No
23.04.2015,12:48:28,$CRX:FPUcodex=0
23.04.2015,12:48:28,$CRX:GS =13
23.04.2015,12:48:28,$CRX:GA =253
23.04.2015,12:48:28,$CRX:Delay=0msec
23.04.2015,12:48:28,$CRX:Frequency=0.0MHz
23.04.2015,12:48:28,$HST:Receiver connected
23.04.2015,12:48:28,$CRX:Sweeplength=0
23.04.2015,12:48:28,$CRX:low_band_max=171MHz
23.04.2015,12:48:28,$CRX:mid_band_max=450MHz
23.04.2015,12:48:28,$CRX:high_band_max=863MHz
23.04.2015,12:48:28,$CRX:Idle=0x
23.04.2015,12:48:28,$CRX:ChargePump=On
23.04.2015,12:48:28,$HST:CD1316LV/IV detected
23.04.2015,12:48:28,$CRX:Debug=Off
23.04.2015,12:48:28,$CRX:Trigger=Extern
23.04.2015,12:48:28,$CRX:FPUcodex=0
23.04.2015,12:48:28,$CRX:GS =13
23.04.2015,12:48:28,$CRX:GA =624
23.04.2015,12:48:28,$CRX:Delay=0msec
23.04.2015,12:48:28,$CRX:Frequency=45.0MHz
23.04.2015,12:48:28,$HST:Receiver connected
23.04.2015,12:48:28,$CRX:Sweeplength=200
23.04.2015,12:48:28,$CRX:low_band_max=171MHz
23.04.2015,12:48:28,$CRX:mid_band_max=450MHz
23.04.2015,12:48:28,$CRX:high_band_max=863MHz
23.04.2015,12:48:28,$CRX:Idle=0x
23.04.2015,12:48:30,$HST:Auto stop due to data loss.
23.04.2015,12:48:31,$HST:Measurement stop
23.04.2015,12:48:31,$HST:Measurement wait...
23.04.2015,12:48:32,$HST:Measurement halted
23.04.2015,12:48:32,$HST:Measurement idle
23.04.2015,12:48:32,$CRX:Stopped
23.04.2015,12:48:32,$HST:Measurement enable
23.04.2015,12:48:32,$CRX:AGC gain = 1.56V
23.04.2015,12:48:32,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:48:32,$CRX:Analog Input = 9.24
23.04.2015,12:48:33,$HST:Check RS232-connection!
23.04.2015,12:48:36,$HST:Attempting Auto-Start
23.04.2015,12:48:37,$HST:Param. RCU due to START
23.04.2015,12:48:37,$HST:Actual focuscode 02
23.04.2015,12:48:37,$HST:Enable data transfer
23.04.2015,12:48:37,$HST:Receiver calibration
23.04.2015,12:48:37,$CRX:Started
23.04.2015,12:48:37,$HST:Start new FITS-file
23.04.2015,12:48:37,$HST:Continous measurement
23.04.2015,12:48:39,$CRX:e-Callisto ETH Zurich
23.04.2015,12:48:39,$HST:Watchdog triggered -> Reset
23.04.2015,12:48:39,$CRX:V1.5, 2006-11-04
23.04.2015,12:48:39,$CRX:ChargePump=On
23.04.2015,12:48:39,$HST:CD1316LV/IV detected
23.04.2015,12:48:39,$CRX:Debug=Off
23.04.2015,12:48:39,$CRX:Trigger=No
23.04.2015,12:48:39,$CRX:FPUcodex=0
23.04.2015,12:48:39,$CRX:GS =13
23.04.2015,12:48:39,$CRX:GA =253
23.04.2015,12:48:39,$CRX:Delay=0msec
23.04.2015,12:48:39,$CRX:Frequency=0.0MHz
23.04.2015,12:48:39,$HST:Receiver connected
23.04.2015,12:48:39,$CRX:Sweeplength=0
23.04.2015,12:48:39,$CRX:low_band_max=171MHz
23.04.2015,12:48:39,$CRX:mid_band_max=450MHz
23.04.2015,12:48:39,$CRX:high_band_max=863MHz
23.04.2015,12:48:39,$CRX:Idle=0x
23.04.2015,12:48:39,$CRX:ChargePump=On
23.04.2015,12:48:39,$HST:CD1316LV/IV detected
23.04.2015,12:48:39,$CRX:Debug=Off
23.04.2015,12:48:39,$CRX:Trigger=Extern
23.04.2015,12:48:39,$CRX:FPUcodex=0
23.04.2015,12:48:39,$CRX:GS =13
23.04.2015,12:48:39,$CRX:GA =624
23.04.2015,12:48:39,$CRX:Delay=0msec
23.04.2015,12:48:39,$CRX:Frequency=45.0MHz
23.04.2015,12:48:39,$HST:Receiver connected
23.04.2015,12:48:39,$CRX:Sweeplength=200
23.04.2015,12:48:39,$CRX:low_band_max=171MHz
23.04.2015,12:48:39,$CRX:mid_band_max=450MHz
23.04.2015,12:48:39,$CRX:high_band_max=863MHz
23.04.2015,12:48:39,$CRX:Idle=0x
23.04.2015,12:48:42,$HST:Auto stop due to data loss.
23.04.2015,12:48:42,$HST:Measurement stop
23.04.2015,12:48:42,$HST:Measurement wait...
23.04.2015,12:48:43,$HST:Measurement halted
23.04.2015,12:48:43,$HST:Measurement idle
23.04.2015,12:48:43,$CRX:Stopped
23.04.2015,12:48:43,$HST:Measurement enable
23.04.2015,12:48:43,$CRX:AGC gain = 1.56V
23.04.2015,12:48:43,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:48:43,$CRX:Analog Input = 9.24
23.04.2015,12:48:45,$HST:Check RS232-connection!
23.04.2015,12:48:48,$HST:Attempting Auto-Start
23.04.2015,12:48:48,$HST:Param. RCU due to START
23.04.2015,12:48:48,$HST:Actual focuscode 02
23.04.2015,12:48:48,$HST:Enable data transfer
23.04.2015,12:48:48,$HST:Receiver calibration
23.04.2015,12:48:48,$CRX:Started
23.04.2015,12:48:48,$HST:Start new FITS-file
23.04.2015,12:48:49,$HST:Continous measurement
23.04.2015,12:48:50,$CRX:e-Callisto ETH Zurich
23.04.2015,12:48:50,$HST:Watchdog triggered -> Reset
23.04.2015,12:48:50,$CRX:V1.5, 2006-11-04
23.04.2015,12:48:50,$CRX:ChargePump=On
23.04.2015,12:48:50,$HST:CD1316LV/IV detected
23.04.2015,12:48:50,$CRX:Debug=Off
23.04.2015,12:48:50,$CRX:Trigger=No
23.04.2015,12:48:50,$CRX:FPUcodex=0
23.04.2015,12:48:50,$CRX:GS =13
23.04.2015,12:48:50,$CRX:GA =253
23.04.2015,12:48:50,$CRX:Delay=0msec
23.04.2015,12:48:50,$CRX:Frequency=0.0MHz
23.04.2015,12:48:50,$HST:Receiver connected
23.04.2015,12:48:50,$CRX:Sweeplength=0
23.04.2015,12:48:50,$CRX:low_band_max=171MHz
23.04.2015,12:48:50,$CRX:mid_band_max=450MHz
23.04.2015,12:48:50,$CRX:high_band_max=863MHz
23.04.2015,12:48:50,$CRX:Idle=0x
23.04.2015,12:48:50,$CRX:ChargePump=On
23.04.2015,12:48:50,$HST:CD1316LV/IV detected
23.04.2015,12:48:50,$CRX:Debug=Off
23.04.2015,12:48:50,$CRX:Trigger=Extern
23.04.2015,12:48:50,$CRX:FPUcodex=0
23.04.2015,12:48:50,$CRX:GS =13
23.04.2015,12:48:50,$CRX:GA =624
23.04.2015,12:48:50,$CRX:Delay=0msec
23.04.2015,12:48:50,$CRX:Frequency=45.0MHz
23.04.2015,12:48:50,$HST:Receiver connected
23.04.2015,12:48:50,$CRX:Sweeplength=200
23.04.2015,12:48:50,$CRX:low_band_max=171MHz
23.04.2015,12:48:50,$CRX:mid_band_max=450MHz
23.04.2015,12:48:50,$CRX:high_band_max=863MHz
23.04.2015,12:48:50,$CRX:Idle=0x
23.04.2015,12:48:53,$HST:Auto stop due to data loss.
23.04.2015,12:48:53,$HST:Measurement stop
23.04.2015,12:48:54,$HST:Measurement wait...
23.04.2015,12:48:54,$HST:Measurement halted
23.04.2015,12:48:55,$HST:Measurement idle
23.04.2015,12:48:55,$CRX:Stopped
23.04.2015,12:48:55,$HST:Measurement enable
23.04.2015,12:48:55,$CRX:AGC gain = 1.57V
23.04.2015,12:48:55,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:48:55,$CRX:Analog Input = 9.24
23.04.2015,12:48:56,$HST:Check RS232-connection!
23.04.2015,12:48:59,$HST:Attempting Auto-Start
23.04.2015,12:48:59,$HST:Param. RCU due to START
23.04.2015,12:48:59,$HST:Actual focuscode 02
23.04.2015,12:49:00,$HST:Enable data transfer
23.04.2015,12:49:00,$HST:Receiver calibration
23.04.2015,12:49:00,$CRX:Started
23.04.2015,12:49:00,$HST:Start new FITS-file
23.04.2015,12:49:00,$HST:Continous measurement
23.04.2015,12:49:02,$CRX:e-Callisto ETH Zurich
23.04.2015,12:49:02,$HST:Watchdog triggered -> Reset
23.04.2015,12:49:02,$CRX:V1.5, 2006-11-04
23.04.2015,12:49:02,$CRX:ChargePump=On
23.04.2015,12:49:02,$HST:CD1316LV/IV detected
23.04.2015,12:49:02,$CRX:Debug=Off
23.04.2015,12:49:02,$CRX:Trigger=No
23.04.2015,12:49:02,$CRX:FPUcodex=0
23.04.2015,12:49:02,$CRX:GS =13
23.04.2015,12:49:02,$CRX:GA =253
23.04.2015,12:49:02,$CRX:Delay=0msec
23.04.2015,12:49:02,$CRX:Frequency=0.0MHz
23.04.2015,12:49:02,$HST:Receiver connected
23.04.2015,12:49:02,$CRX:Sweeplength=0
23.04.2015,12:49:02,$CRX:low_band_max=171MHz
23.04.2015,12:49:02,$CRX:mid_band_max=450MHz
23.04.2015,12:49:02,$CRX:high_band_max=863MHz
23.04.2015,12:49:02,$CRX:Idle=0x
23.04.2015,12:49:02,$CRX:ChargePump=On
23.04.2015,12:49:02,$HST:CD1316LV/IV detected
23.04.2015,12:49:02,$CRX:Debug=Off
23.04.2015,12:49:02,$CRX:Trigger=Extern
23.04.2015,12:49:02,$CRX:FPUcodex=0
23.04.2015,12:49:02,$CRX:GS =13
23.04.2015,12:49:02,$CRX:GA =624
23.04.2015,12:49:02,$CRX:Delay=0msec
23.04.2015,12:49:02,$CRX:Frequency=45.0MHz
23.04.2015,12:49:02,$HST:Receiver connected
23.04.2015,12:49:02,$CRX:Sweeplength=200
23.04.2015,12:49:02,$CRX:low_band_max=171MHz
23.04.2015,12:49:02,$CRX:mid_band_max=450MHz
23.04.2015,12:49:02,$CRX:high_band_max=863MHz
23.04.2015,12:49:02,$CRX:Idle=0x
23.04.2015,12:49:05,$HST:Auto stop due to data loss.
23.04.2015,12:49:05,$HST:Measurement stop
23.04.2015,12:49:05,$HST:Measurement wait...
23.04.2015,12:49:06,$HST:Measurement halted
23.04.2015,12:49:06,$HST:Measurement idle
23.04.2015,12:49:06,$CRX:Stopped
23.04.2015,12:49:06,$HST:Measurement enable
23.04.2015,12:49:06,$CRX:AGC gain = 1.57V
23.04.2015,12:49:06,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:49:06,$CRX:Analog Input = 9.24
23.04.2015,12:49:08,$HST:Check RS232-connection!
23.04.2015,12:49:11,$HST:Attempting Auto-Start
23.04.2015,12:49:11,$HST:Param. RCU due to START
23.04.2015,12:49:11,$HST:Actual focuscode 02
23.04.2015,12:49:11,$HST:Enable data transfer
23.04.2015,12:49:11,$HST:Receiver calibration
23.04.2015,12:49:11,$CRX:Started
23.04.2015,12:49:11,$HST:Start new FITS-file
23.04.2015,12:49:11,$HST:Continous measurement
23.04.2015,12:49:13,$CRX:e-Callisto ETH Zurich
23.04.2015,12:49:13,$HST:Watchdog triggered -> Reset
23.04.2015,12:49:13,$CRX:V1.5, 2006-11-04
23.04.2015,12:49:13,$CRX:ChargePump=On
23.04.2015,12:49:13,$HST:CD1316LV/IV detected
23.04.2015,12:49:13,$CRX:Debug=Off
23.04.2015,12:49:13,$CRX:Trigger=No
23.04.2015,12:49:13,$CRX:FPUcodex=0
23.04.2015,12:49:13,$CRX:GS =13
23.04.2015,12:49:13,$CRX:GA =253
23.04.2015,12:49:13,$CRX:Delay=0msec
23.04.2015,12:49:13,$CRX:Frequency=0.0MHz
23.04.2015,12:49:13,$HST:Receiver connected
23.04.2015,12:49:13,$CRX:Sweeplength=0
23.04.2015,12:49:13,$CRX:low_band_max=171MHz
23.04.2015,12:49:13,$CRX:mid_band_max=450MHz
23.04.2015,12:49:13,$CRX:high_band_max=863MHz
23.04.2015,12:49:13,$CRX:Idle=0x
23.04.2015,12:49:13,$CRX:ChargePump=On
23.04.2015,12:49:13,$HST:CD1316LV/IV detected
23.04.2015,12:49:13,$CRX:Debug=Off
23.04.2015,12:49:13,$CRX:Trigger=Extern
23.04.2015,12:49:13,$CRX:FPUcodex=0
23.04.2015,12:49:13,$CRX:GS =13
23.04.2015,12:49:13,$CRX:GA =624
23.04.2015,12:49:13,$CRX:Delay=0msec
23.04.2015,12:49:13,$CRX:Frequency=45.0MHz
23.04.2015,12:49:13,$HST:Receiver connected
23.04.2015,12:49:13,$CRX:Sweeplength=200
23.04.2015,12:49:13,$CRX:low_band_max=171MHz
23.04.2015,12:49:13,$CRX:mid_band_max=450MHz
23.04.2015,12:49:13,$CRX:high_band_max=863MHz
23.04.2015,12:49:13,$CRX:Idle=0x
23.04.2015,12:49:16,$HST:Auto stop due to data loss.
23.04.2015,12:49:16,$HST:Measurement stop
23.04.2015,12:49:16,$HST:Measurement wait...
23.04.2015,12:49:17,$HST:Measurement halted
23.04.2015,12:49:17,$HST:Measurement idle
23.04.2015,12:49:17,$CRX:Stopped
23.04.2015,12:49:18,$HST:Measurement enable
23.04.2015,12:49:18,$CRX:AGC gain = 1.57V
23.04.2015,12:49:18,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:49:18,$CRX:Analog Input = 9.24
23.04.2015,12:49:19,$HST:Check RS232-connection!
23.04.2015,12:49:22,$HST:Attempting Auto-Start
23.04.2015,12:49:22,$HST:Param. RCU due to START
23.04.2015,12:49:22,$HST:Actual focuscode 02
23.04.2015,12:49:22,$HST:Enable data transfer
23.04.2015,12:49:22,$HST:Receiver calibration
23.04.2015,12:49:22,$CRX:Started
23.04.2015,12:49:23,$HST:Start new FITS-file
23.04.2015,12:49:23,$HST:Continous measurement
23.04.2015,12:49:25,$CRX:e-Callisto ETH Zurich
23.04.2015,12:49:25,$HST:Watchdog triggered -> Reset
23.04.2015,12:49:25,$CRX:V1.5, 2006-11-04
23.04.2015,12:49:25,$CRX:ChargePump=On
23.04.2015,12:49:25,$HST:CD1316LV/IV detected
23.04.2015,12:49:25,$CRX:Debug=Off
23.04.2015,12:49:25,$CRX:Trigger=No
23.04.2015,12:49:25,$CRX:FPUcodex=0
23.04.2015,12:49:25,$CRX:GS =13
23.04.2015,12:49:25,$CRX:GA =253
23.04.2015,12:49:25,$CRX:Delay=0msec
23.04.2015,12:49:25,$CRX:Frequency=0.0MHz
23.04.2015,12:49:25,$HST:Receiver connected
23.04.2015,12:49:25,$CRX:Sweeplength=0
23.04.2015,12:49:25,$CRX:low_band_max=171MHz
23.04.2015,12:49:25,$CRX:mid_band_max=450MHz
23.04.2015,12:49:25,$CRX:high_band_max=863MHz
23.04.2015,12:49:25,$CRX:Idle=0x
23.04.2015,12:49:25,$CRX:ChargePump=On
23.04.2015,12:49:25,$HST:CD1316LV/IV detected
23.04.2015,12:49:25,$CRX:Debug=Off
23.04.2015,12:49:25,$CRX:Trigger=Extern
23.04.2015,12:49:25,$CRX:FPUcodex=0
23.04.2015,12:49:25,$CRX:GS =13
23.04.2015,12:49:25,$CRX:GA =624
23.04.2015,12:49:25,$CRX:Delay=0msec
23.04.2015,12:49:25,$CRX:Frequency=45.0MHz
23.04.2015,12:49:25,$HST:Receiver connected
23.04.2015,12:49:25,$CRX:Sweeplength=200
23.04.2015,12:49:25,$CRX:low_band_max=171MHz
23.04.2015,12:49:25,$CRX:mid_band_max=450MHz
23.04.2015,12:49:25,$CRX:high_band_max=863MHz
23.04.2015,12:49:25,$CRX:Idle=0x
23.04.2015,12:49:28,$HST:Auto stop due to data loss.
23.04.2015,12:49:28,$HST:Measurement stop
23.04.2015,12:49:28,$HST:Measurement wait...
23.04.2015,12:49:29,$HST:Measurement halted
23.04.2015,12:49:29,$HST:Measurement idle
23.04.2015,12:49:29,$CRX:Stopped
23.04.2015,12:49:29,$HST:Measurement enable
23.04.2015,12:49:29,$CRX:AGC gain = 1.57V
23.04.2015,12:49:29,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:49:29,$CRX:Analog Input = 9.24
23.04.2015,12:49:31,$HST:Check RS232-connection!
23.04.2015,12:49:34,$HST:Attempting Auto-Start
23.04.2015,12:49:34,$HST:Param. RCU due to START
23.04.2015,12:49:34,$HST:Actual focuscode 02
23.04.2015,12:49:34,$HST:Enable data transfer
23.04.2015,12:49:34,$HST:Receiver calibration
23.04.2015,12:49:34,$CRX:Started
23.04.2015,12:49:34,$HST:Start new FITS-file
23.04.2015,12:49:34,$HST:Continous measurement
23.04.2015,12:49:36,$CRX:e-Callisto ETH Zurich
23.04.2015,12:49:36,$HST:Watchdog triggered -> Reset
23.04.2015,12:49:36,$CRX:V1.5, 2006-11-04
23.04.2015,12:49:36,$CRX:ChargePump=On
23.04.2015,12:49:36,$HST:CD1316LV/IV detected
23.04.2015,12:49:36,$CRX:Debug=Off
23.04.2015,12:49:36,$CRX:Trigger=No
23.04.2015,12:49:36,$CRX:FPUcodex=0
23.04.2015,12:49:36,$CRX:GS =13
23.04.2015,12:49:36,$CRX:GA =253
23.04.2015,12:49:36,$CRX:Delay=0msec
23.04.2015,12:49:36,$CRX:Frequency=0.0MHz
23.04.2015,12:49:36,$HST:Receiver connected
23.04.2015,12:49:36,$CRX:Sweeplength=0
23.04.2015,12:49:36,$CRX:low_band_max=171MHz
23.04.2015,12:49:36,$CRX:mid_band_max=450MHz
23.04.2015,12:49:36,$CRX:high_band_max=863MHz
23.04.2015,12:49:36,$CRX:Idle=0x
23.04.2015,12:49:36,$CRX:ChargePump=On
23.04.2015,12:49:36,$HST:CD1316LV/IV detected
23.04.2015,12:49:36,$CRX:Debug=Off
23.04.2015,12:49:36,$CRX:Trigger=Extern
23.04.2015,12:49:36,$CRX:FPUcodex=0
23.04.2015,12:49:36,$CRX:GS =13
23.04.2015,12:49:36,$CRX:GA =624
23.04.2015,12:49:36,$CRX:Delay=0msec
23.04.2015,12:49:36,$CRX:Frequency=45.0MHz
23.04.2015,12:49:36,$HST:Receiver connected
23.04.2015,12:49:36,$CRX:Sweeplength=200
23.04.2015,12:49:36,$CRX:low_band_max=171MHz
23.04.2015,12:49:36,$CRX:mid_band_max=450MHz
23.04.2015,12:49:36,$CRX:high_band_max=863MHz
23.04.2015,12:49:36,$CRX:Idle=0x
23.04.2015,12:49:39,$HST:Auto stop due to data loss.
23.04.2015,12:49:39,$HST:Measurement stop
23.04.2015,12:49:39,$HST:Measurement wait...
23.04.2015,12:49:40,$HST:Measurement halted
23.04.2015,12:49:40,$HST:Measurement idle
23.04.2015,12:49:40,$CRX:Stopped
23.04.2015,12:49:40,$HST:Measurement enable
23.04.2015,12:49:40,$CRX:AGC gain = 1.57V
23.04.2015,12:49:40,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:49:40,$CRX:Analog Input = 9.24
23.04.2015,12:49:42,$HST:Check RS232-connection!
23.04.2015,12:49:45,$HST:Attempting Auto-Start
23.04.2015,12:49:45,$HST:Param. RCU due to START
23.04.2015,12:49:45,$HST:Actual focuscode 02
23.04.2015,12:49:45,$HST:Enable data transfer
23.04.2015,12:49:45,$HST:Receiver calibration
23.04.2015,12:49:45,$CRX:Started
23.04.2015,12:49:45,$HST:Start new FITS-file
23.04.2015,12:49:46,$HST:Continous measurement
23.04.2015,12:49:47,$CRX:e-Callisto ETH Zurich
23.04.2015,12:49:47,$HST:Watchdog triggered -> Reset
23.04.2015,12:49:47,$CRX:V1.5, 2006-11-04
23.04.2015,12:49:48,$CRX:ChargePump=On
23.04.2015,12:49:48,$HST:CD1316LV/IV detected
23.04.2015,12:49:48,$CRX:Debug=Off
23.04.2015,12:49:48,$CRX:Trigger=No
23.04.2015,12:49:48,$CRX:FPUcodex=0
23.04.2015,12:49:48,$CRX:GS =13
23.04.2015,12:49:48,$CRX:GA =253
23.04.2015,12:49:48,$CRX:Delay=0msec
23.04.2015,12:49:48,$CRX:Frequency=0.0MHz
23.04.2015,12:49:48,$HST:Receiver connected
23.04.2015,12:49:48,$CRX:Sweeplength=0
23.04.2015,12:49:48,$CRX:low_band_max=171MHz
23.04.2015,12:49:48,$CRX:mid_band_max=450MHz
23.04.2015,12:49:48,$CRX:high_band_max=863MHz
23.04.2015,12:49:48,$CRX:Idle=0x
23.04.2015,12:49:48,$CRX:ChargePump=On
23.04.2015,12:49:48,$HST:CD1316LV/IV detected
23.04.2015,12:49:48,$CRX:Debug=Off
23.04.2015,12:49:48,$CRX:Trigger=Extern
23.04.2015,12:49:48,$CRX:FPUcodex=0
23.04.2015,12:49:48,$CRX:GS =13
23.04.2015,12:49:48,$CRX:GA =624
23.04.2015,12:49:48,$CRX:Delay=0msec
23.04.2015,12:49:48,$CRX:Frequency=45.0MHz
23.04.2015,12:49:48,$HST:Receiver connected
23.04.2015,12:49:48,$CRX:Sweeplength=200
23.04.2015,12:49:48,$CRX:low_band_max=171MHz
23.04.2015,12:49:48,$CRX:mid_band_max=450MHz
23.04.2015,12:49:48,$CRX:high_band_max=863MHz
23.04.2015,12:49:48,$CRX:Idle=0x
23.04.2015,12:49:50,$HST:Auto stop due to data loss.
23.04.2015,12:49:51,$HST:Measurement stop
23.04.2015,12:49:51,$HST:Measurement wait...
23.04.2015,12:49:51,$HST:Measurement halted
23.04.2015,12:49:52,$HST:Measurement idle
23.04.2015,12:49:52,$CRX:Stopped
23.04.2015,12:49:52,$HST:Measurement enable
23.04.2015,12:49:52,$CRX:AGC gain = 1.57V
23.04.2015,12:49:52,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:49:52,$CRX:Analog Input = 9.24
23.04.2015,12:49:53,$HST:Check RS232-connection!
23.04.2015,12:49:56,$HST:Attempting Auto-Start
23.04.2015,12:49:57,$HST:Param. RCU due to START
23.04.2015,12:49:57,$HST:Actual focuscode 02
23.04.2015,12:49:57,$HST:Enable data transfer
23.04.2015,12:49:57,$HST:Receiver calibration
23.04.2015,12:49:57,$CRX:Started
23.04.2015,12:49:57,$HST:Start new FITS-file
23.04.2015,12:49:57,$HST:Continous measurement
23.04.2015,12:49:59,$CRX:e-Callisto ETH Zurich
23.04.2015,12:49:59,$HST:Watchdog triggered -> Reset
23.04.2015,12:49:59,$CRX:V1.5, 2006-11-04
23.04.2015,12:49:59,$CRX:ChargePump=On
23.04.2015,12:49:59,$HST:CD1316LV/IV detected
23.04.2015,12:49:59,$CRX:Debug=Off
23.04.2015,12:49:59,$CRX:Trigger=No
23.04.2015,12:49:59,$CRX:FPUcodex=0
23.04.2015,12:49:59,$CRX:GS =13
23.04.2015,12:49:59,$CRX:GA =253
23.04.2015,12:49:59,$CRX:Delay=0msec
23.04.2015,12:49:59,$CRX:Frequency=0.0MHz
23.04.2015,12:49:59,$HST:Receiver connected
23.04.2015,12:49:59,$CRX:Sweeplength=0
23.04.2015,12:49:59,$CRX:low_band_max=171MHz
23.04.2015,12:49:59,$CRX:mid_band_max=450MHz
23.04.2015,12:49:59,$CRX:high_band_max=863MHz
23.04.2015,12:49:59,$CRX:Idle=0x
23.04.2015,12:49:59,$CRX:ChargePump=On
23.04.2015,12:49:59,$HST:CD1316LV/IV detected
23.04.2015,12:49:59,$CRX:Debug=Off
23.04.2015,12:49:59,$CRX:Trigger=Extern
23.04.2015,12:49:59,$CRX:FPUcodex=0
23.04.2015,12:49:59,$CRX:GS =13
23.04.2015,12:49:59,$CRX:GA =624
23.04.2015,12:49:59,$CRX:Delay=0msec
23.04.2015,12:49:59,$CRX:Frequency=45.0MHz
23.04.2015,12:49:59,$HST:Receiver connected
23.04.2015,12:49:59,$CRX:Sweeplength=200
23.04.2015,12:49:59,$CRX:low_band_max=171MHz
23.04.2015,12:49:59,$CRX:mid_band_max=450MHz
23.04.2015,12:49:59,$CRX:high_band_max=863MHz
23.04.2015,12:49:59,$CRX:Idle=0x
23.04.2015,12:50:02,$HST:Auto stop due to data loss.
23.04.2015,12:50:02,$HST:Measurement stop
23.04.2015,12:50:02,$HST:Measurement wait...
23.04.2015,12:50:03,$HST:Measurement halted
23.04.2015,12:50:03,$HST:Measurement idle
23.04.2015,12:50:03,$CRX:Stopped
23.04.2015,12:50:03,$HST:Measurement enable
23.04.2015,12:50:03,$CRX:AGC gain = 1.56V
23.04.2015,12:50:03,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:50:03,$CRX:Analog Input = 9.24
23.04.2015,12:50:05,$HST:Check RS232-connection!
23.04.2015,12:50:08,$HST:Attempting Auto-Start
23.04.2015,12:50:08,$HST:Param. RCU due to START
23.04.2015,12:50:08,$HST:Actual focuscode 02
23.04.2015,12:50:08,$HST:Enable data transfer
23.04.2015,12:50:08,$HST:Receiver calibration
23.04.2015,12:50:08,$CRX:Started
23.04.2015,12:50:08,$HST:Start new FITS-file
23.04.2015,12:50:09,$HST:Continous measurement
23.04.2015,12:50:10,$CRX:e-Callisto ETH Zurich
23.04.2015,12:50:10,$HST:Watchdog triggered -> Reset
23.04.2015,12:50:10,$CRX:V1.5, 2006-11-04
23.04.2015,12:50:10,$CRX:ChargePump=On
23.04.2015,12:50:10,$HST:CD1316LV/IV detected
23.04.2015,12:50:10,$CRX:Debug=Off
23.04.2015,12:50:10,$CRX:Trigger=No
23.04.2015,12:50:10,$CRX:FPUcodex=0
23.04.2015,12:50:10,$CRX:GS =13
23.04.2015,12:50:10,$CRX:GA =253
23.04.2015,12:50:10,$CRX:Delay=0msec
23.04.2015,12:50:10,$CRX:Frequency=0.0MHz
23.04.2015,12:50:10,$HST:Receiver connected
23.04.2015,12:50:10,$CRX:Sweeplength=0
23.04.2015,12:50:10,$CRX:low_band_max=171MHz
23.04.2015,12:50:10,$CRX:mid_band_max=450MHz
23.04.2015,12:50:10,$CRX:high_band_max=863MHz
23.04.2015,12:50:10,$CRX:Idle=0x
23.04.2015,12:50:10,$CRX:ChargePump=On
23.04.2015,12:50:10,$HST:CD1316LV/IV detected
23.04.2015,12:50:10,$CRX:Debug=Off
23.04.2015,12:50:10,$CRX:Trigger=Extern
23.04.2015,12:50:10,$CRX:FPUcodex=0
23.04.2015,12:50:10,$CRX:GS =13
23.04.2015,12:50:10,$CRX:GA =624
23.04.2015,12:50:10,$CRX:Delay=0msec
23.04.2015,12:50:10,$CRX:Frequency=45.0MHz
23.04.2015,12:50:10,$HST:Receiver connected
23.04.2015,12:50:10,$CRX:Sweeplength=200
23.04.2015,12:50:10,$CRX:low_band_max=171MHz
23.04.2015,12:50:10,$CRX:mid_band_max=450MHz
23.04.2015,12:50:10,$CRX:high_band_max=863MHz
23.04.2015,12:50:10,$CRX:Idle=0x
23.04.2015,12:50:13,$HST:Auto stop due to data loss.
23.04.2015,12:50:13,$HST:Measurement stop
23.04.2015,12:50:14,$HST:Measurement wait...
23.04.2015,12:50:14,$HST:Measurement halted
23.04.2015,12:50:15,$HST:Measurement idle
23.04.2015,12:50:15,$CRX:Stopped
23.04.2015,12:50:15,$HST:Measurement enable
23.04.2015,12:50:15,$CRX:AGC gain = 1.57V
23.04.2015,12:50:15,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:50:15,$CRX:Analog Input = 9.24
23.04.2015,12:50:16,$HST:Check RS232-connection!
23.04.2015,12:50:19,$HST:Attempting Auto-Start
23.04.2015,12:50:19,$HST:Param. RCU due to START
23.04.2015,12:50:19,$HST:Actual focuscode 02
23.04.2015,12:50:20,$HST:Enable data transfer
23.04.2015,12:50:20,$HST:Receiver calibration
23.04.2015,12:50:20,$CRX:Started
23.04.2015,12:50:20,$HST:Start new FITS-file
23.04.2015,12:50:20,$HST:Continous measurement
23.04.2015,12:50:22,$CRX:e-Callisto ETH Zurich
23.04.2015,12:50:22,$HST:Watchdog triggered -> Reset
23.04.2015,12:50:22,$CRX:V1.5, 2006-11-04
23.04.2015,12:50:22,$CRX:ChargePump=On
23.04.2015,12:50:22,$HST:CD1316LV/IV detected
23.04.2015,12:50:22,$CRX:Debug=Off
23.04.2015,12:50:22,$CRX:Trigger=No
23.04.2015,12:50:22,$CRX:FPUcodex=0
23.04.2015,12:50:22,$CRX:GS =13
23.04.2015,12:50:22,$CRX:GA =253
23.04.2015,12:50:22,$CRX:Delay=0msec
23.04.2015,12:50:22,$CRX:Frequency=0.0MHz
23.04.2015,12:50:22,$HST:Receiver connected
23.04.2015,12:50:22,$CRX:Sweeplength=0
23.04.2015,12:50:22,$CRX:low_band_max=171MHz
23.04.2015,12:50:22,$CRX:mid_band_max=450MHz
23.04.2015,12:50:22,$CRX:high_band_max=863MHz
23.04.2015,12:50:22,$CRX:Idle=0x
23.04.2015,12:50:22,$CRX:ChargePump=On
23.04.2015,12:50:22,$HST:CD1316LV/IV detected
23.04.2015,12:50:22,$CRX:Debug=Off
23.04.2015,12:50:22,$CRX:Trigger=Extern
23.04.2015,12:50:22,$CRX:FPUcodex=0
23.04.2015,12:50:22,$CRX:GS =13
23.04.2015,12:50:22,$CRX:GA =624
23.04.2015,12:50:22,$CRX:Delay=0msec
23.04.2015,12:50:22,$CRX:Frequency=45.0MHz
23.04.2015,12:50:22,$HST:Receiver connected
23.04.2015,12:50:22,$CRX:Sweeplength=200
23.04.2015,12:50:22,$CRX:low_band_max=171MHz
23.04.2015,12:50:22,$CRX:mid_band_max=450MHz
23.04.2015,12:50:22,$CRX:high_band_max=863MHz
23.04.2015,12:50:22,$CRX:Idle=0x
23.04.2015,12:50:25,$HST:Auto stop due to data loss.
23.04.2015,12:50:25,$HST:Measurement stop
23.04.2015,12:50:25,$HST:Measurement wait...
23.04.2015,12:50:26,$HST:Measurement halted
23.04.2015,12:50:26,$HST:Measurement idle
23.04.2015,12:50:26,$CRX:Stopped
23.04.2015,12:50:26,$HST:Measurement enable
23.04.2015,12:50:26,$CRX:AGC gain = 1.57V
23.04.2015,12:50:26,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:50:26,$CRX:Analog Input = 9.24
23.04.2015,12:50:28,$HST:Check RS232-connection!
23.04.2015,12:50:31,$HST:Attempting Auto-Start
23.04.2015,12:50:31,$HST:Param. RCU due to START
23.04.2015,12:50:31,$HST:Actual focuscode 02
23.04.2015,12:50:31,$HST:Enable data transfer
23.04.2015,12:50:31,$HST:Receiver calibration
23.04.2015,12:50:31,$CRX:Started
23.04.2015,12:50:31,$HST:Start new FITS-file
23.04.2015,12:50:31,$HST:Continous measurement
23.04.2015,12:50:33,$CRX:e-Callisto ETH Zurich
23.04.2015,12:50:33,$HST:Watchdog triggered -> Reset
23.04.2015,12:50:33,$CRX:V1.5, 2006-11-04
23.04.2015,12:50:33,$CRX:ChargePump=On
23.04.2015,12:50:33,$HST:CD1316LV/IV detected
23.04.2015,12:50:33,$CRX:Debug=Off
23.04.2015,12:50:33,$CRX:Trigger=No
23.04.2015,12:50:33,$CRX:FPUcodex=0
23.04.2015,12:50:33,$CRX:GS =13
23.04.2015,12:50:33,$CRX:GA =253
23.04.2015,12:50:33,$CRX:Delay=0msec
23.04.2015,12:50:33,$CRX:Frequency=0.0MHz
23.04.2015,12:50:33,$HST:Receiver connected
23.04.2015,12:50:33,$CRX:Sweeplength=0
23.04.2015,12:50:33,$CRX:low_band_max=171MHz
23.04.2015,12:50:33,$CRX:mid_band_max=450MHz
23.04.2015,12:50:33,$CRX:high_band_max=863MHz
23.04.2015,12:50:33,$CRX:Idle=0x
23.04.2015,12:50:33,$CRX:ChargePump=On
23.04.2015,12:50:33,$HST:CD1316LV/IV detected
23.04.2015,12:50:33,$CRX:Debug=Off
23.04.2015,12:50:33,$CRX:Trigger=Extern
23.04.2015,12:50:33,$CRX:FPUcodex=0
23.04.2015,12:50:33,$CRX:GS =13
23.04.2015,12:50:33,$CRX:GA =624
23.04.2015,12:50:33,$CRX:Delay=0msec
23.04.2015,12:50:33,$CRX:Frequency=45.0MHz
23.04.2015,12:50:33,$HST:Receiver connected
23.04.2015,12:50:33,$CRX:Sweeplength=200
23.04.2015,12:50:33,$CRX:low_band_max=171MHz
23.04.2015,12:50:33,$CRX:mid_band_max=450MHz
23.04.2015,12:50:33,$CRX:high_band_max=863MHz
23.04.2015,12:50:33,$CRX:Idle=0x
23.04.2015,12:50:36,$HST:Auto stop due to data loss.
23.04.2015,12:50:36,$HST:Measurement stop
23.04.2015,12:50:36,$HST:Measurement wait...
23.04.2015,12:50:37,$HST:Measurement halted
23.04.2015,12:50:37,$HST:Measurement idle
23.04.2015,12:50:37,$CRX:Stopped
23.04.2015,12:50:38,$HST:Measurement enable
23.04.2015,12:50:38,$CRX:AGC gain = 1.56V
23.04.2015,12:50:38,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:50:38,$CRX:Analog Input = 9.24
23.04.2015,12:50:39,$HST:Check RS232-connection!
23.04.2015,12:50:42,$HST:Attempting Auto-Start
23.04.2015,12:50:42,$HST:Param. RCU due to START
23.04.2015,12:50:42,$HST:Actual focuscode 02
23.04.2015,12:50:42,$HST:Enable data transfer
23.04.2015,12:50:42,$HST:Receiver calibration
23.04.2015,12:50:42,$CRX:Started
23.04.2015,12:50:43,$HST:Start new FITS-file
23.04.2015,12:50:43,$HST:Continous measurement
23.04.2015,12:50:44,$CRX:e-Callisto ETH Zurich
23.04.2015,12:50:44,$HST:Watchdog triggered -> Reset
23.04.2015,12:50:44,$CRX:V1.5, 2006-11-04
23.04.2015,12:50:45,$CRX:ChargePump=On
23.04.2015,12:50:45,$HST:CD1316LV/IV detected
23.04.2015,12:50:45,$CRX:Debug=Off
23.04.2015,12:50:45,$CRX:Trigger=No
23.04.2015,12:50:45,$CRX:FPUcodex=0
23.04.2015,12:50:45,$CRX:GS =13
23.04.2015,12:50:45,$CRX:GA =253
23.04.2015,12:50:45,$CRX:Delay=0msec
23.04.2015,12:50:45,$CRX:Frequency=0.0MHz
23.04.2015,12:50:45,$HST:Receiver connected
23.04.2015,12:50:45,$CRX:Sweeplength=0
23.04.2015,12:50:45,$CRX:low_band_max=171MHz
23.04.2015,12:50:45,$CRX:mid_band_max=450MHz
23.04.2015,12:50:45,$CRX:high_band_max=863MHz
23.04.2015,12:50:45,$CRX:Idle=0x
23.04.2015,12:50:45,$CRX:ChargePump=On
23.04.2015,12:50:45,$HST:CD1316LV/IV detected
23.04.2015,12:50:45,$CRX:Debug=Off
23.04.2015,12:50:45,$CRX:Trigger=Extern
23.04.2015,12:50:45,$CRX:FPUcodex=0
23.04.2015,12:50:45,$CRX:GS =13
23.04.2015,12:50:45,$CRX:GA =624
23.04.2015,12:50:45,$CRX:Delay=0msec
23.04.2015,12:50:45,$CRX:Frequency=45.0MHz
23.04.2015,12:50:45,$HST:Receiver connected
23.04.2015,12:50:45,$CRX:Sweeplength=200
23.04.2015,12:50:45,$CRX:low_band_max=171MHz
23.04.2015,12:50:45,$CRX:mid_band_max=450MHz
23.04.2015,12:50:45,$CRX:high_band_max=863MHz
23.04.2015,12:50:45,$CRX:Idle=0x
23.04.2015,12:50:47,$HST:Auto stop due to data loss.
23.04.2015,12:50:48,$HST:Measurement stop
23.04.2015,12:50:48,$HST:Measurement wait...
23.04.2015,12:50:49,$HST:Measurement halted
23.04.2015,12:50:49,$HST:Measurement idle
23.04.2015,12:50:49,$CRX:Stopped
23.04.2015,12:50:49,$HST:Measurement enable
23.04.2015,12:50:49,$CRX:AGC gain = 1.57V
23.04.2015,12:50:49,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:50:49,$CRX:Analog Input = 9.24
23.04.2015,12:50:50,$HST:Check RS232-connection!
23.04.2015,12:50:53,$HST:Attempting Auto-Start
23.04.2015,12:50:54,$HST:Param. RCU due to START
23.04.2015,12:50:54,$HST:Actual focuscode 02
23.04.2015,12:50:54,$HST:Enable data transfer
23.04.2015,12:50:54,$HST:Receiver calibration
23.04.2015,12:50:54,$CRX:Started
23.04.2015,12:50:54,$HST:Start new FITS-file
23.04.2015,12:50:54,$HST:Continous measurement
23.04.2015,12:50:56,$CRX:e-Callisto ETH Zurich
23.04.2015,12:50:56,$HST:Watchdog triggered -> Reset
23.04.2015,12:50:56,$CRX:V1.5, 2006-11-04
23.04.2015,12:50:56,$CRX:ChargePump=On
23.04.2015,12:50:56,$HST:CD1316LV/IV detected
23.04.2015,12:50:56,$CRX:Debug=Off
23.04.2015,12:50:56,$CRX:Trigger=No
23.04.2015,12:50:56,$CRX:FPUcodex=0
23.04.2015,12:50:56,$CRX:GS =13
23.04.2015,12:50:56,$CRX:GA =253
23.04.2015,12:50:56,$CRX:Delay=0msec
23.04.2015,12:50:56,$CRX:Frequency=0.0MHz
23.04.2015,12:50:56,$HST:Receiver connected
23.04.2015,12:50:56,$CRX:Sweeplength=0
23.04.2015,12:50:56,$CRX:low_band_max=171MHz
23.04.2015,12:50:56,$CRX:mid_band_max=450MHz
23.04.2015,12:50:56,$CRX:high_band_max=863MHz
23.04.2015,12:50:56,$CRX:Idle=0x
23.04.2015,12:50:56,$CRX:ChargePump=On
23.04.2015,12:50:56,$HST:CD1316LV/IV detected
23.04.2015,12:50:56,$CRX:Debug=Off
23.04.2015,12:50:56,$CRX:Trigger=Extern
23.04.2015,12:50:56,$CRX:FPUcodex=0
23.04.2015,12:50:56,$CRX:GS =13
23.04.2015,12:50:56,$CRX:GA =624
23.04.2015,12:50:56,$CRX:Delay=0msec
23.04.2015,12:50:56,$CRX:Frequency=45.0MHz
23.04.2015,12:50:56,$HST:Receiver connected
23.04.2015,12:50:56,$CRX:Sweeplength=200
23.04.2015,12:50:56,$CRX:low_band_max=171MHz
23.04.2015,12:50:56,$CRX:mid_band_max=450MHz
23.04.2015,12:50:56,$CRX:high_band_max=863MHz
23.04.2015,12:50:56,$CRX:Idle=0x
23.04.2015,12:50:59,$HST:Auto stop due to data loss.
23.04.2015,12:50:59,$HST:Measurement stop
23.04.2015,12:50:59,$HST:Measurement wait...
23.04.2015,12:51:00,$HST:Measurement halted
23.04.2015,12:51:00,$HST:Measurement idle
23.04.2015,12:51:00,$CRX:Stopped
23.04.2015,12:51:00,$HST:Measurement enable
23.04.2015,12:51:00,$CRX:AGC gain = 1.57V
23.04.2015,12:51:00,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:51:00,$CRX:Analog Input = 9.24
23.04.2015,12:51:02,$HST:Check RS232-connection!
23.04.2015,12:51:05,$HST:Attempting Auto-Start
23.04.2015,12:51:05,$HST:Param. RCU due to START
23.04.2015,12:51:05,$HST:Actual focuscode 02
23.04.2015,12:51:05,$HST:Enable data transfer
23.04.2015,12:51:05,$HST:Receiver calibration
23.04.2015,12:51:05,$CRX:Started
23.04.2015,12:51:05,$HST:Start new FITS-file
23.04.2015,12:51:06,$HST:Continous measurement
23.04.2015,12:51:07,$CRX:e-Callisto ETH Zurich
23.04.2015,12:51:07,$HST:Watchdog triggered -> Reset
23.04.2015,12:51:07,$CRX:V1.5, 2006-11-04
23.04.2015,12:51:07,$CRX:ChargePump=On
23.04.2015,12:51:07,$HST:CD1316LV/IV detected
23.04.2015,12:51:07,$CRX:Debug=Off
23.04.2015,12:51:07,$CRX:Trigger=No
23.04.2015,12:51:07,$CRX:FPUcodex=0
23.04.2015,12:51:07,$CRX:GS =13
23.04.2015,12:51:07,$CRX:GA =253
23.04.2015,12:51:07,$CRX:Delay=0msec
23.04.2015,12:51:07,$CRX:Frequency=0.0MHz
23.04.2015,12:51:07,$HST:Receiver connected
23.04.2015,12:51:07,$CRX:Sweeplength=0
23.04.2015,12:51:07,$CRX:low_band_max=171MHz
23.04.2015,12:51:07,$CRX:mid_band_max=450MHz
23.04.2015,12:51:07,$CRX:high_band_max=863MHz
23.04.2015,12:51:07,$CRX:Idle=0x
23.04.2015,12:51:07,$CRX:ChargePump=On
23.04.2015,12:51:07,$HST:CD1316LV/IV detected
23.04.2015,12:51:07,$CRX:Debug=Off
23.04.2015,12:51:07,$CRX:Trigger=Extern
23.04.2015,12:51:07,$CRX:FPUcodex=0
23.04.2015,12:51:07,$CRX:GS =13
23.04.2015,12:51:07,$CRX:GA =624
23.04.2015,12:51:07,$CRX:Delay=0msec
23.04.2015,12:51:07,$CRX:Frequency=45.0MHz
23.04.2015,12:51:07,$HST:Receiver connected
23.04.2015,12:51:07,$CRX:Sweeplength=200
23.04.2015,12:51:07,$CRX:low_band_max=171MHz
23.04.2015,12:51:07,$CRX:mid_band_max=450MHz
23.04.2015,12:51:07,$CRX:high_band_max=863MHz
23.04.2015,12:51:07,$CRX:Idle=0x
23.04.2015,12:51:10,$HST:Auto stop due to data loss.
23.04.2015,12:51:10,$HST:Measurement stop
23.04.2015,12:51:11,$HST:Measurement wait...
23.04.2015,12:51:11,$HST:Measurement halted
23.04.2015,12:51:12,$HST:Measurement idle
23.04.2015,12:51:12,$CRX:Stopped
23.04.2015,12:51:12,$HST:Measurement enable
23.04.2015,12:51:12,$CRX:AGC gain = 1.57V
23.04.2015,12:51:12,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:51:12,$CRX:Analog Input = 9.24
23.04.2015,12:51:13,$HST:Check RS232-connection!
23.04.2015,12:51:16,$HST:Attempting Auto-Start
23.04.2015,12:51:16,$HST:Param. RCU due to START
23.04.2015,12:51:16,$HST:Actual focuscode 02
23.04.2015,12:51:17,$HST:Enable data transfer
23.04.2015,12:51:17,$HST:Receiver calibration
23.04.2015,12:51:17,$CRX:Started
23.04.2015,12:51:17,$HST:Start new FITS-file
23.04.2015,12:51:17,$HST:Continous measurement
23.04.2015,12:51:19,$CRX:e-Callisto ETH Zurich
23.04.2015,12:51:19,$HST:Watchdog triggered -> Reset
23.04.2015,12:51:19,$CRX:V1.5, 2006-11-04
23.04.2015,12:51:19,$CRX:ChargePump=On
23.04.2015,12:51:19,$HST:CD1316LV/IV detected
23.04.2015,12:51:19,$CRX:Debug=Off
23.04.2015,12:51:19,$CRX:Trigger=No
23.04.2015,12:51:19,$CRX:FPUcodex=0
23.04.2015,12:51:19,$CRX:GS =13
23.04.2015,12:51:19,$CRX:GA =253
23.04.2015,12:51:19,$CRX:Delay=0msec
23.04.2015,12:51:19,$CRX:Frequency=0.0MHz
23.04.2015,12:51:19,$HST:Receiver connected
23.04.2015,12:51:19,$CRX:Sweeplength=0
23.04.2015,12:51:19,$CRX:low_band_max=171MHz
23.04.2015,12:51:19,$CRX:mid_band_max=450MHz
23.04.2015,12:51:19,$CRX:high_band_max=863MHz
23.04.2015,12:51:19,$CRX:Idle=0x
23.04.2015,12:51:19,$CRX:ChargePump=On
23.04.2015,12:51:19,$HST:CD1316LV/IV detected
23.04.2015,12:51:19,$CRX:Debug=Off
23.04.2015,12:51:19,$CRX:Trigger=Extern
23.04.2015,12:51:19,$CRX:FPUcodex=0
23.04.2015,12:51:19,$CRX:GS =13
23.04.2015,12:51:19,$CRX:GA =624
23.04.2015,12:51:19,$CRX:Delay=0msec
23.04.2015,12:51:19,$CRX:Frequency=45.0MHz
23.04.2015,12:51:19,$HST:Receiver connected
23.04.2015,12:51:19,$CRX:Sweeplength=200
23.04.2015,12:51:19,$CRX:low_band_max=171MHz
23.04.2015,12:51:19,$CRX:mid_band_max=450MHz
23.04.2015,12:51:19,$CRX:high_band_max=863MHz
23.04.2015,12:51:19,$CRX:Idle=0x
23.04.2015,12:51:22,$HST:Auto stop due to data loss.
23.04.2015,12:51:22,$HST:Measurement stop
23.04.2015,12:51:22,$HST:Measurement wait...
23.04.2015,12:51:23,$HST:Measurement halted
23.04.2015,12:51:23,$HST:Measurement idle
23.04.2015,12:51:23,$CRX:Stopped
23.04.2015,12:51:23,$HST:Measurement enable
23.04.2015,12:51:23,$CRX:AGC gain = 1.57V
23.04.2015,12:51:23,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:51:23,$CRX:Analog Input = 9.24
23.04.2015,12:51:25,$HST:Check RS232-connection!
23.04.2015,12:51:28,$HST:Attempting Auto-Start
23.04.2015,12:51:28,$HST:Param. RCU due to START
23.04.2015,12:51:28,$HST:Actual focuscode 02
23.04.2015,12:51:28,$HST:Enable data transfer
23.04.2015,12:51:28,$HST:Receiver calibration
23.04.2015,12:51:28,$CRX:Started
23.04.2015,12:51:28,$HST:Start new FITS-file
23.04.2015,12:51:28,$HST:Continous measurement
23.04.2015,12:51:30,$CRX:e-Callisto ETH Zurich
23.04.2015,12:51:30,$HST:Watchdog triggered -> Reset
23.04.2015,12:51:30,$CRX:V1.5, 2006-11-04
23.04.2015,12:51:30,$CRX:ChargePump=On
23.04.2015,12:51:30,$HST:CD1316LV/IV detected
23.04.2015,12:51:30,$CRX:Debug=Off
23.04.2015,12:51:30,$CRX:Trigger=No
23.04.2015,12:51:30,$CRX:FPUcodex=0
23.04.2015,12:51:30,$CRX:GS =13
23.04.2015,12:51:30,$CRX:GA =253
23.04.2015,12:51:30,$CRX:Delay=0msec
23.04.2015,12:51:30,$CRX:Frequency=0.0MHz
23.04.2015,12:51:30,$HST:Receiver connected
23.04.2015,12:51:30,$CRX:Sweeplength=0
23.04.2015,12:51:30,$CRX:low_band_max=171MHz
23.04.2015,12:51:30,$CRX:mid_band_max=450MHz
23.04.2015,12:51:30,$CRX:high_band_max=863MHz
23.04.2015,12:51:30,$CRX:Idle=0x
23.04.2015,12:51:30,$CRX:ChargePump=On
23.04.2015,12:51:30,$HST:CD1316LV/IV detected
23.04.2015,12:51:30,$CRX:Debug=Off
23.04.2015,12:51:30,$CRX:Trigger=Extern
23.04.2015,12:51:30,$CRX:FPUcodex=0
23.04.2015,12:51:30,$CRX:GS =13
23.04.2015,12:51:30,$CRX:GA =624
23.04.2015,12:51:30,$CRX:Delay=0msec
23.04.2015,12:51:30,$CRX:Frequency=45.0MHz
23.04.2015,12:51:30,$HST:Receiver connected
23.04.2015,12:51:30,$CRX:Sweeplength=200
23.04.2015,12:51:30,$CRX:low_band_max=171MHz
23.04.2015,12:51:30,$CRX:mid_band_max=450MHz
23.04.2015,12:51:30,$CRX:high_band_max=863MHz
23.04.2015,12:51:30,$CRX:Idle=0x
23.04.2015,12:51:33,$HST:Auto stop due to data loss.
23.04.2015,12:51:33,$HST:Measurement stop
23.04.2015,12:51:34,$HST:Measurement wait...
23.04.2015,12:51:34,$HST:Measurement halted
23.04.2015,12:51:34,$HST:Measurement idle
23.04.2015,12:51:34,$CRX:Stopped
23.04.2015,12:51:35,$HST:Measurement enable
23.04.2015,12:51:35,$CRX:AGC gain = 1.56V
23.04.2015,12:51:35,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:51:35,$CRX:Analog Input = 9.24
23.04.2015,12:51:36,$HST:Check RS232-connection!
23.04.2015,12:51:39,$HST:Attempting Auto-Start
23.04.2015,12:51:39,$HST:Param. RCU due to START
23.04.2015,12:51:39,$HST:Actual focuscode 02
23.04.2015,12:51:39,$HST:Enable data transfer
23.04.2015,12:51:39,$HST:Receiver calibration
23.04.2015,12:51:39,$CRX:Started
23.04.2015,12:51:40,$HST:Start new FITS-file
23.04.2015,12:51:40,$HST:Continous measurement
23.04.2015,12:51:42,$CRX:e-Callisto ETH Zurich
23.04.2015,12:51:42,$HST:Watchdog triggered -> Reset
23.04.2015,12:51:42,$CRX:V1.5, 2006-11-04
23.04.2015,12:51:42,$CRX:ChargePump=On
23.04.2015,12:51:42,$HST:CD1316LV/IV detected
23.04.2015,12:51:42,$CRX:Debug=Off
23.04.2015,12:51:42,$CRX:Trigger=No
23.04.2015,12:51:42,$CRX:FPUcodex=0
23.04.2015,12:51:42,$CRX:GS =13
23.04.2015,12:51:42,$CRX:GA =253
23.04.2015,12:51:42,$CRX:Delay=0msec
23.04.2015,12:51:42,$CRX:Frequency=0.0MHz
23.04.2015,12:51:42,$HST:Receiver connected
23.04.2015,12:51:42,$CRX:Sweeplength=0
23.04.2015,12:51:42,$CRX:low_band_max=171MHz
23.04.2015,12:51:42,$CRX:mid_band_max=450MHz
23.04.2015,12:51:42,$CRX:high_band_max=863MHz
23.04.2015,12:51:42,$CRX:Idle=0x
23.04.2015,12:51:42,$CRX:ChargePump=On
23.04.2015,12:51:42,$HST:CD1316LV/IV detected
23.04.2015,12:51:42,$CRX:Debug=Off
23.04.2015,12:51:42,$CRX:Trigger=Extern
23.04.2015,12:51:42,$CRX:FPUcodex=0
23.04.2015,12:51:42,$CRX:GS =13
23.04.2015,12:51:42,$CRX:GA =624
23.04.2015,12:51:42,$CRX:Delay=0msec
23.04.2015,12:51:42,$CRX:Frequency=45.0MHz
23.04.2015,12:51:42,$HST:Receiver connected
23.04.2015,12:51:42,$CRX:Sweeplength=200
23.04.2015,12:51:42,$CRX:low_band_max=171MHz
23.04.2015,12:51:42,$CRX:mid_band_max=450MHz
23.04.2015,12:51:42,$CRX:high_band_max=863MHz
23.04.2015,12:51:42,$CRX:Idle=0x
23.04.2015,12:51:45,$HST:Auto stop due to data loss.
23.04.2015,12:51:45,$HST:Measurement stop
23.04.2015,12:51:45,$HST:Measurement wait...
23.04.2015,12:51:46,$HST:Measurement halted
23.04.2015,12:51:46,$HST:Measurement idle
23.04.2015,12:51:46,$CRX:Stopped
23.04.2015,12:51:46,$HST:Measurement enable
23.04.2015,12:51:46,$CRX:AGC gain = 1.57V
23.04.2015,12:51:46,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:51:46,$CRX:Analog Input = 9.24
23.04.2015,12:51:48,$HST:Check RS232-connection!
23.04.2015,12:51:51,$HST:Attempting Auto-Start
23.04.2015,12:51:51,$HST:Param. RCU due to START
23.04.2015,12:51:51,$HST:Actual focuscode 02
23.04.2015,12:51:51,$HST:Enable data transfer
23.04.2015,12:51:51,$HST:Receiver calibration
23.04.2015,12:51:51,$CRX:Started
23.04.2015,12:51:51,$HST:Start new FITS-file
23.04.2015,12:51:51,$HST:Continous measurement
23.04.2015,12:51:53,$CRX:e-Callisto ETH Zurich
23.04.2015,12:51:53,$HST:Watchdog triggered -> Reset
23.04.2015,12:51:53,$CRX:V1.5, 2006-11-04
23.04.2015,12:51:53,$CRX:ChargePump=On
23.04.2015,12:51:53,$HST:CD1316LV/IV detected
23.04.2015,12:51:53,$CRX:Debug=Off
23.04.2015,12:51:53,$CRX:Trigger=No
23.04.2015,12:51:53,$CRX:FPUcodex=0
23.04.2015,12:51:53,$CRX:GS =13
23.04.2015,12:51:53,$CRX:GA =253
23.04.2015,12:51:53,$CRX:Delay=0msec
23.04.2015,12:51:53,$CRX:Frequency=0.0MHz
23.04.2015,12:51:53,$HST:Receiver connected
23.04.2015,12:51:53,$CRX:Sweeplength=0
23.04.2015,12:51:53,$CRX:low_band_max=171MHz
23.04.2015,12:51:53,$CRX:mid_band_max=450MHz
23.04.2015,12:51:53,$CRX:high_band_max=863MHz
23.04.2015,12:51:53,$CRX:Idle=0x
23.04.2015,12:51:53,$CRX:ChargePump=On
23.04.2015,12:51:53,$HST:CD1316LV/IV detected
23.04.2015,12:51:53,$CRX:Debug=Off
23.04.2015,12:51:53,$CRX:Trigger=Extern
23.04.2015,12:51:53,$CRX:FPUcodex=0
23.04.2015,12:51:53,$CRX:GS =13
23.04.2015,12:51:53,$CRX:GA =624
23.04.2015,12:51:53,$CRX:Delay=0msec
23.04.2015,12:51:53,$CRX:Frequency=45.0MHz
23.04.2015,12:51:53,$HST:Receiver connected
23.04.2015,12:51:53,$CRX:Sweeplength=200
23.04.2015,12:51:53,$CRX:low_band_max=171MHz
23.04.2015,12:51:53,$CRX:mid_band_max=450MHz
23.04.2015,12:51:53,$CRX:high_band_max=863MHz
23.04.2015,12:51:53,$CRX:Idle=0x
23.04.2015,12:51:56,$HST:Auto stop due to data loss.
23.04.2015,12:51:56,$HST:Measurement stop
23.04.2015,12:51:56,$HST:Measurement wait...
23.04.2015,12:51:57,$HST:Measurement halted
23.04.2015,12:51:57,$HST:Measurement idle
23.04.2015,12:51:57,$CRX:Stopped
23.04.2015,12:51:57,$HST:Measurement enable
23.04.2015,12:51:57,$CRX:AGC gain = 1.56V
23.04.2015,12:51:57,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:51:57,$CRX:Analog Input = 9.24
23.04.2015,12:51:59,$HST:Check RS232-connection!
23.04.2015,12:52:02,$HST:Attempting Auto-Start
23.04.2015,12:52:02,$HST:Param. RCU due to START
23.04.2015,12:52:02,$HST:Actual focuscode 02
23.04.2015,12:52:02,$HST:Enable data transfer
23.04.2015,12:52:02,$HST:Receiver calibration
23.04.2015,12:52:02,$CRX:Started
23.04.2015,12:52:03,$HST:Start new FITS-file
23.04.2015,12:52:03,$HST:Continous measurement
23.04.2015,12:52:04,$CRX:e-Callisto ETH Zurich
23.04.2015,12:52:04,$HST:Watchdog triggered -> Reset
23.04.2015,12:52:04,$CRX:V1.5, 2006-11-04
23.04.2015,12:52:05,$CRX:ChargePump=On
23.04.2015,12:52:05,$HST:CD1316LV/IV detected
23.04.2015,12:52:05,$CRX:Debug=Off
23.04.2015,12:52:05,$CRX:Trigger=No
23.04.2015,12:52:05,$CRX:FPUcodex=0
23.04.2015,12:52:05,$CRX:GS =13
23.04.2015,12:52:05,$CRX:GA =253
23.04.2015,12:52:05,$CRX:Delay=0msec
23.04.2015,12:52:05,$CRX:Frequency=0.0MHz
23.04.2015,12:52:05,$HST:Receiver connected
23.04.2015,12:52:05,$CRX:Sweeplength=0
23.04.2015,12:52:05,$CRX:low_band_max=171MHz
23.04.2015,12:52:05,$CRX:mid_band_max=450MHz
23.04.2015,12:52:05,$CRX:high_band_max=863MHz
23.04.2015,12:52:05,$CRX:Idle=0x
23.04.2015,12:52:05,$CRX:ChargePump=On
23.04.2015,12:52:05,$HST:CD1316LV/IV detected
23.04.2015,12:52:05,$CRX:Debug=Off
23.04.2015,12:52:05,$CRX:Trigger=Extern
23.04.2015,12:52:05,$CRX:FPUcodex=0
23.04.2015,12:52:05,$CRX:GS =13
23.04.2015,12:52:05,$CRX:GA =624
23.04.2015,12:52:05,$CRX:Delay=0msec
23.04.2015,12:52:05,$CRX:Frequency=45.0MHz
23.04.2015,12:52:05,$HST:Receiver connected
23.04.2015,12:52:05,$CRX:Sweeplength=200
23.04.2015,12:52:05,$CRX:low_band_max=171MHz
23.04.2015,12:52:05,$CRX:mid_band_max=450MHz
23.04.2015,12:52:05,$CRX:high_band_max=863MHz
23.04.2015,12:52:05,$CRX:Idle=0x
23.04.2015,12:52:07,$HST:Auto stop due to data loss.
23.04.2015,12:52:08,$HST:Measurement stop
23.04.2015,12:52:08,$HST:Measurement wait...
23.04.2015,12:52:09,$HST:Measurement halted
23.04.2015,12:52:09,$HST:Measurement idle
23.04.2015,12:52:09,$CRX:Stopped
23.04.2015,12:52:09,$HST:Measurement enable
23.04.2015,12:52:09,$CRX:AGC gain = 1.56V
23.04.2015,12:52:09,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:52:09,$CRX:Analog Input = 9.24
23.04.2015,12:52:10,$HST:Check RS232-connection!
23.04.2015,12:52:13,$HST:Attempting Auto-Start
23.04.2015,12:52:14,$HST:Param. RCU due to START
23.04.2015,12:52:14,$HST:Actual focuscode 02
23.04.2015,12:52:14,$HST:Enable data transfer
23.04.2015,12:52:14,$HST:Receiver calibration
23.04.2015,12:52:14,$CRX:Started
23.04.2015,12:52:14,$HST:Start new FITS-file
23.04.2015,12:52:14,$HST:Continous measurement
23.04.2015,12:52:16,$CRX:e-Callisto ETH Zurich
23.04.2015,12:52:16,$HST:Watchdog triggered -> Reset
23.04.2015,12:52:16,$CRX:V1.5, 2006-11-04
23.04.2015,12:52:16,$CRX:ChargePump=On
23.04.2015,12:52:16,$HST:CD1316LV/IV detected
23.04.2015,12:52:16,$CRX:Debug=Off
23.04.2015,12:52:16,$CRX:Trigger=No
23.04.2015,12:52:16,$CRX:FPUcodex=0
23.04.2015,12:52:16,$CRX:GS =13
23.04.2015,12:52:16,$CRX:GA =253
23.04.2015,12:52:16,$CRX:Delay=0msec
23.04.2015,12:52:16,$CRX:Frequency=0.0MHz
23.04.2015,12:52:16,$HST:Receiver connected
23.04.2015,12:52:16,$CRX:Sweeplength=0
23.04.2015,12:52:16,$CRX:low_band_max=171MHz
23.04.2015,12:52:16,$CRX:mid_band_max=450MHz
23.04.2015,12:52:16,$CRX:high_band_max=863MHz
23.04.2015,12:52:16,$CRX:Idle=0x
23.04.2015,12:52:16,$CRX:ChargePump=On
23.04.2015,12:52:16,$HST:CD1316LV/IV detected
23.04.2015,12:52:16,$CRX:Debug=Off
23.04.2015,12:52:16,$CRX:Trigger=Extern
23.04.2015,12:52:16,$CRX:FPUcodex=0
23.04.2015,12:52:16,$CRX:GS =13
23.04.2015,12:52:16,$CRX:GA =624
23.04.2015,12:52:16,$CRX:Delay=0msec
23.04.2015,12:52:16,$CRX:Frequency=45.0MHz
23.04.2015,12:52:16,$HST:Receiver connected
23.04.2015,12:52:16,$CRX:Sweeplength=200
23.04.2015,12:52:16,$CRX:low_band_max=171MHz
23.04.2015,12:52:16,$CRX:mid_band_max=450MHz
23.04.2015,12:52:16,$CRX:high_band_max=863MHz
23.04.2015,12:52:16,$CRX:Idle=0x
23.04.2015,12:52:19,$HST:Auto stop due to data loss.
23.04.2015,12:52:19,$HST:Measurement stop
23.04.2015,12:52:19,$HST:Measurement wait...
23.04.2015,12:52:20,$HST:Measurement halted
23.04.2015,12:52:20,$HST:Measurement idle
23.04.2015,12:52:20,$CRX:Stopped
23.04.2015,12:52:20,$HST:Measurement enable
23.04.2015,12:52:20,$CRX:AGC gain = 1.57V
23.04.2015,12:52:20,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:52:20,$CRX:Analog Input = 9.24
23.04.2015,12:52:22,$HST:Check RS232-connection!
23.04.2015,12:52:25,$HST:Attempting Auto-Start
23.04.2015,12:52:25,$HST:Param. RCU due to START
23.04.2015,12:52:25,$HST:Actual focuscode 02
23.04.2015,12:52:25,$HST:Enable data transfer
23.04.2015,12:52:25,$HST:Receiver calibration
23.04.2015,12:52:25,$CRX:Started
23.04.2015,12:52:25,$HST:Start new FITS-file
23.04.2015,12:52:26,$HST:Continous measurement
23.04.2015,12:52:27,$CRX:e-Callisto ETH Zurich
23.04.2015,12:52:27,$HST:Watchdog triggered -> Reset
23.04.2015,12:52:27,$CRX:V1.5, 2006-11-04
23.04.2015,12:52:27,$CRX:ChargePump=On
23.04.2015,12:52:27,$HST:CD1316LV/IV detected
23.04.2015,12:52:27,$CRX:Debug=Off
23.04.2015,12:52:27,$CRX:Trigger=No
23.04.2015,12:52:27,$CRX:FPUcodex=0
23.04.2015,12:52:27,$CRX:GS =13
23.04.2015,12:52:27,$CRX:GA =253
23.04.2015,12:52:27,$CRX:Delay=0msec
23.04.2015,12:52:27,$CRX:Frequency=0.0MHz
23.04.2015,12:52:27,$HST:Receiver connected
23.04.2015,12:52:27,$CRX:Sweeplength=0
23.04.2015,12:52:27,$CRX:low_band_max=171MHz
23.04.2015,12:52:27,$CRX:mid_band_max=450MHz
23.04.2015,12:52:27,$CRX:high_band_max=863MHz
23.04.2015,12:52:27,$CRX:Idle=0x
23.04.2015,12:52:27,$CRX:ChargePump=On
23.04.2015,12:52:27,$HST:CD1316LV/IV detected
23.04.2015,12:52:27,$CRX:Debug=Off
23.04.2015,12:52:27,$CRX:Trigger=Extern
23.04.2015,12:52:27,$CRX:FPUcodex=0
23.04.2015,12:52:27,$CRX:GS =13
23.04.2015,12:52:27,$CRX:GA =624
23.04.2015,12:52:27,$CRX:Delay=0msec
23.04.2015,12:52:27,$CRX:Frequency=45.0MHz
23.04.2015,12:52:27,$HST:Receiver connected
23.04.2015,12:52:27,$CRX:Sweeplength=200
23.04.2015,12:52:27,$CRX:low_band_max=171MHz
23.04.2015,12:52:27,$CRX:mid_band_max=450MHz
23.04.2015,12:52:27,$CRX:high_band_max=863MHz
23.04.2015,12:52:27,$CRX:Idle=0x
23.04.2015,12:52:30,$HST:Auto stop due to data loss.
23.04.2015,12:52:30,$HST:Measurement stop
23.04.2015,12:52:31,$HST:Measurement wait...
23.04.2015,12:52:31,$HST:Measurement halted
23.04.2015,12:52:32,$HST:Measurement idle
23.04.2015,12:52:32,$CRX:Stopped
23.04.2015,12:52:32,$HST:Measurement enable
23.04.2015,12:52:32,$CRX:AGC gain = 1.56V
23.04.2015,12:52:32,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:52:32,$CRX:Analog Input = 9.24
23.04.2015,12:52:33,$HST:Check RS232-connection!
23.04.2015,12:52:36,$HST:Attempting Auto-Start
23.04.2015,12:52:36,$HST:Param. RCU due to START
23.04.2015,12:52:36,$HST:Actual focuscode 02
23.04.2015,12:52:37,$HST:Enable data transfer
23.04.2015,12:52:37,$HST:Receiver calibration
23.04.2015,12:52:37,$CRX:Started
23.04.2015,12:52:37,$HST:Start new FITS-file
23.04.2015,12:52:37,$HST:Continous measurement
23.04.2015,12:52:39,$CRX:e-Callisto ETH Zurich
23.04.2015,12:52:39,$HST:Watchdog triggered -> Reset
23.04.2015,12:52:39,$CRX:V1.5, 2006-11-04
23.04.2015,12:52:39,$CRX:ChargePump=On
23.04.2015,12:52:39,$HST:CD1316LV/IV detected
23.04.2015,12:52:39,$CRX:Debug=Off
23.04.2015,12:52:39,$CRX:Trigger=No
23.04.2015,12:52:39,$CRX:FPUcodex=0
23.04.2015,12:52:39,$CRX:GS =13
23.04.2015,12:52:39,$CRX:GA =253
23.04.2015,12:52:39,$CRX:Delay=0msec
23.04.2015,12:52:39,$CRX:Frequency=0.0MHz
23.04.2015,12:52:39,$HST:Receiver connected
23.04.2015,12:52:39,$CRX:Sweeplength=0
23.04.2015,12:52:39,$CRX:low_band_max=171MHz
23.04.2015,12:52:39,$CRX:mid_band_max=450MHz
23.04.2015,12:52:39,$CRX:high_band_max=863MHz
23.04.2015,12:52:39,$CRX:Idle=0x
23.04.2015,12:52:39,$CRX:ChargePump=On
23.04.2015,12:52:39,$HST:CD1316LV/IV detected
23.04.2015,12:52:39,$CRX:Debug=Off
23.04.2015,12:52:39,$CRX:Trigger=Extern
23.04.2015,12:52:39,$CRX:FPUcodex=0
23.04.2015,12:52:39,$CRX:GS =13
23.04.2015,12:52:39,$CRX:GA =624
23.04.2015,12:52:39,$CRX:Delay=0msec
23.04.2015,12:52:39,$CRX:Frequency=45.0MHz
23.04.2015,12:52:39,$HST:Receiver connected
23.04.2015,12:52:39,$CRX:Sweeplength=200
23.04.2015,12:52:39,$CRX:low_band_max=171MHz
23.04.2015,12:52:39,$CRX:mid_band_max=450MHz
23.04.2015,12:52:39,$CRX:high_band_max=863MHz
23.04.2015,12:52:39,$CRX:Idle=0x
23.04.2015,12:52:42,$HST:Auto stop due to data loss.
23.04.2015,12:52:42,$HST:Measurement stop
23.04.2015,12:52:42,$HST:Measurement wait...
23.04.2015,12:52:43,$HST:Measurement halted
23.04.2015,12:52:43,$HST:Measurement idle
23.04.2015,12:52:43,$CRX:Stopped
23.04.2015,12:52:43,$HST:Measurement enable
23.04.2015,12:52:43,$CRX:AGC gain = 1.56V
23.04.2015,12:52:43,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:52:43,$CRX:Analog Input = 9.24
23.04.2015,12:52:45,$HST:Check RS232-connection!
23.04.2015,12:52:48,$HST:Attempting Auto-Start
23.04.2015,12:52:48,$HST:Param. RCU due to START
23.04.2015,12:52:48,$HST:Actual focuscode 02
23.04.2015,12:52:48,$HST:Enable data transfer
23.04.2015,12:52:48,$HST:Receiver calibration
23.04.2015,12:52:48,$CRX:Started
23.04.2015,12:52:48,$HST:Start new FITS-file
23.04.2015,12:52:48,$HST:Continous measurement
23.04.2015,12:52:50,$CRX:e-Callisto ETH Zurich
23.04.2015,12:52:50,$HST:Watchdog triggered -> Reset
23.04.2015,12:52:50,$CRX:V1.5, 2006-11-04
23.04.2015,12:52:50,$CRX:ChargePump=On
23.04.2015,12:52:50,$HST:CD1316LV/IV detected
23.04.2015,12:52:50,$CRX:Debug=Off
23.04.2015,12:52:50,$CRX:Trigger=No
23.04.2015,12:52:50,$CRX:FPUcodex=0
23.04.2015,12:52:50,$CRX:GS =13
23.04.2015,12:52:50,$CRX:GA =253
23.04.2015,12:52:50,$CRX:Delay=0msec
23.04.2015,12:52:50,$CRX:Frequency=0.0MHz
23.04.2015,12:52:50,$HST:Receiver connected
23.04.2015,12:52:50,$CRX:Sweeplength=0
23.04.2015,12:52:50,$CRX:low_band_max=171MHz
23.04.2015,12:52:50,$CRX:mid_band_max=450MHz
23.04.2015,12:52:50,$CRX:high_band_max=863MHz
23.04.2015,12:52:50,$CRX:Idle=0x
23.04.2015,12:52:50,$CRX:ChargePump=On
23.04.2015,12:52:50,$HST:CD1316LV/IV detected
23.04.2015,12:52:50,$CRX:Debug=Off
23.04.2015,12:52:50,$CRX:Trigger=Extern
23.04.2015,12:52:50,$CRX:FPUcodex=0
23.04.2015,12:52:50,$CRX:GS =13
23.04.2015,12:52:50,$CRX:GA =624
23.04.2015,12:52:50,$CRX:Delay=0msec
23.04.2015,12:52:50,$CRX:Frequency=45.0MHz
23.04.2015,12:52:50,$HST:Receiver connected
23.04.2015,12:52:50,$CRX:Sweeplength=200
23.04.2015,12:52:50,$CRX:low_band_max=171MHz
23.04.2015,12:52:50,$CRX:mid_band_max=450MHz
23.04.2015,12:52:50,$CRX:high_band_max=863MHz
23.04.2015,12:52:50,$CRX:Idle=0x
23.04.2015,12:52:53,$HST:Auto stop due to data loss.
23.04.2015,12:52:53,$HST:Measurement stop
23.04.2015,12:52:53,$HST:Measurement wait...
23.04.2015,12:52:54,$HST:Measurement halted
23.04.2015,12:52:54,$HST:Measurement idle
23.04.2015,12:52:54,$CRX:Stopped
23.04.2015,12:52:55,$HST:Measurement enable
23.04.2015,12:52:55,$CRX:AGC gain = 1.57V
23.04.2015,12:52:55,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:52:55,$CRX:Analog Input = 9.24
23.04.2015,12:52:56,$HST:Check RS232-connection!
23.04.2015,12:52:59,$HST:Attempting Auto-Start
23.04.2015,12:52:59,$HST:Param. RCU due to START
23.04.2015,12:52:59,$HST:Actual focuscode 02
23.04.2015,12:52:59,$HST:Enable data transfer
23.04.2015,12:52:59,$HST:Receiver calibration
23.04.2015,12:52:59,$CRX:Started
23.04.2015,12:53:00,$HST:Start new FITS-file
23.04.2015,12:53:00,$HST:Continous measurement
23.04.2015,12:53:01,$CRX:e-Callisto ETH Zurich
23.04.2015,12:53:01,$HST:Watchdog triggered -> Reset
23.04.2015,12:53:01,$CRX:V1.5, 2006-11-04
23.04.2015,12:53:02,$CRX:ChargePump=On
23.04.2015,12:53:02,$HST:CD1316LV/IV detected
23.04.2015,12:53:02,$CRX:Debug=Off
23.04.2015,12:53:02,$CRX:Trigger=No
23.04.2015,12:53:02,$CRX:FPUcodex=0
23.04.2015,12:53:02,$CRX:GS =13
23.04.2015,12:53:02,$CRX:GA =253
23.04.2015,12:53:02,$CRX:Delay=0msec
23.04.2015,12:53:02,$CRX:Frequency=0.0MHz
23.04.2015,12:53:02,$HST:Receiver connected
23.04.2015,12:53:02,$CRX:Sweeplength=0
23.04.2015,12:53:02,$CRX:low_band_max=171MHz
23.04.2015,12:53:02,$CRX:mid_band_max=450MHz
23.04.2015,12:53:02,$CRX:high_band_max=863MHz
23.04.2015,12:53:02,$CRX:Idle=0x
23.04.2015,12:53:02,$CRX:ChargePump=On
23.04.2015,12:53:02,$HST:CD1316LV/IV detected
23.04.2015,12:53:02,$CRX:Debug=Off
23.04.2015,12:53:02,$CRX:Trigger=Extern
23.04.2015,12:53:02,$CRX:FPUcodex=0
23.04.2015,12:53:02,$CRX:GS =13
23.04.2015,12:53:02,$CRX:GA =624
23.04.2015,12:53:02,$CRX:Delay=0msec
23.04.2015,12:53:02,$CRX:Frequency=45.0MHz
23.04.2015,12:53:02,$HST:Receiver connected
23.04.2015,12:53:02,$CRX:Sweeplength=200
23.04.2015,12:53:02,$CRX:low_band_max=171MHz
23.04.2015,12:53:02,$CRX:mid_band_max=450MHz
23.04.2015,12:53:02,$CRX:high_band_max=863MHz
23.04.2015,12:53:02,$CRX:Idle=0x
23.04.2015,12:53:04,$HST:Auto stop due to data loss.
23.04.2015,12:53:05,$HST:Measurement stop
23.04.2015,12:53:05,$HST:Measurement wait...
23.04.2015,12:53:06,$HST:Measurement halted
23.04.2015,12:53:06,$HST:Measurement idle
23.04.2015,12:53:06,$CRX:Stopped
23.04.2015,12:53:06,$HST:Measurement enable
23.04.2015,12:53:06,$CRX:AGC gain = 1.57V
23.04.2015,12:53:06,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:53:06,$CRX:Analog Input = 9.24
23.04.2015,12:53:07,$HST:Check RS232-connection!
23.04.2015,12:53:10,$HST:Attempting Auto-Start
23.04.2015,12:53:11,$HST:Param. RCU due to START
23.04.2015,12:53:11,$HST:Actual focuscode 02
23.04.2015,12:53:11,$HST:Enable data transfer
23.04.2015,12:53:11,$HST:Receiver calibration
23.04.2015,12:53:11,$CRX:Started
23.04.2015,12:53:11,$HST:Start new FITS-file
23.04.2015,12:53:11,$HST:Continous measurement
23.04.2015,12:53:13,$CRX:e-Callisto ETH Zurich
23.04.2015,12:53:13,$HST:Watchdog triggered -> Reset
23.04.2015,12:53:13,$CRX:V1.5, 2006-11-04
23.04.2015,12:53:13,$CRX:ChargePump=On
23.04.2015,12:53:13,$HST:CD1316LV/IV detected
23.04.2015,12:53:13,$CRX:Debug=Off
23.04.2015,12:53:13,$CRX:Trigger=No
23.04.2015,12:53:13,$CRX:FPUcodex=0
23.04.2015,12:53:13,$CRX:GS =13
23.04.2015,12:53:13,$CRX:GA =253
23.04.2015,12:53:13,$CRX:Delay=0msec
23.04.2015,12:53:13,$CRX:Frequency=0.0MHz
23.04.2015,12:53:13,$HST:Receiver connected
23.04.2015,12:53:13,$CRX:Sweeplength=0
23.04.2015,12:53:13,$CRX:low_band_max=171MHz
23.04.2015,12:53:13,$CRX:mid_band_max=450MHz
23.04.2015,12:53:13,$CRX:high_band_max=863MHz
23.04.2015,12:53:13,$CRX:Idle=0x
23.04.2015,12:53:13,$CRX:ChargePump=On
23.04.2015,12:53:13,$HST:CD1316LV/IV detected
23.04.2015,12:53:13,$CRX:Debug=Off
23.04.2015,12:53:13,$CRX:Trigger=Extern
23.04.2015,12:53:13,$CRX:FPUcodex=0
23.04.2015,12:53:13,$CRX:GS =13
23.04.2015,12:53:13,$CRX:GA =624
23.04.2015,12:53:13,$CRX:Delay=0msec
23.04.2015,12:53:13,$CRX:Frequency=45.0MHz
23.04.2015,12:53:13,$HST:Receiver connected
23.04.2015,12:53:13,$CRX:Sweeplength=200
23.04.2015,12:53:13,$CRX:low_band_max=171MHz
23.04.2015,12:53:13,$CRX:mid_band_max=450MHz
23.04.2015,12:53:13,$CRX:high_band_max=863MHz
23.04.2015,12:53:13,$CRX:Idle=0x
23.04.2015,12:53:16,$HST:Auto stop due to data loss.
23.04.2015,12:53:16,$HST:Measurement stop
23.04.2015,12:53:16,$HST:Measurement wait...
23.04.2015,12:53:17,$HST:Measurement halted
23.04.2015,12:53:17,$HST:Measurement idle
23.04.2015,12:53:17,$CRX:Stopped
23.04.2015,12:53:17,$HST:Measurement enable
23.04.2015,12:53:17,$CRX:AGC gain = 1.57V
23.04.2015,12:53:17,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:53:17,$CRX:Analog Input = 9.24
23.04.2015,12:53:19,$HST:Check RS232-connection!
23.04.2015,12:53:22,$HST:Attempting Auto-Start
23.04.2015,12:53:22,$HST:Param. RCU due to START
23.04.2015,12:53:22,$HST:Actual focuscode 02
23.04.2015,12:53:22,$HST:Enable data transfer
23.04.2015,12:53:22,$HST:Receiver calibration
23.04.2015,12:53:22,$CRX:Started
23.04.2015,12:53:22,$HST:Start new FITS-file
23.04.2015,12:53:23,$HST:Continous measurement
23.04.2015,12:53:24,$CRX:e-Callisto ETH Zurich
23.04.2015,12:53:24,$HST:Watchdog triggered -> Reset
23.04.2015,12:53:24,$CRX:V1.5, 2006-11-04
23.04.2015,12:53:25,$CRX:ChargePump=On
23.04.2015,12:53:25,$HST:CD1316LV/IV detected
23.04.2015,12:53:25,$CRX:Debug=Off
23.04.2015,12:53:25,$CRX:Trigger=No
23.04.2015,12:53:25,$CRX:FPUcodex=0
23.04.2015,12:53:25,$CRX:GS =13
23.04.2015,12:53:25,$CRX:GA =253
23.04.2015,12:53:25,$CRX:Delay=0msec
23.04.2015,12:53:25,$CRX:Frequency=0.0MHz
23.04.2015,12:53:25,$HST:Receiver connected
23.04.2015,12:53:25,$CRX:Sweeplength=0
23.04.2015,12:53:25,$CRX:low_band_max=171MHz
23.04.2015,12:53:25,$CRX:mid_band_max=450MHz
23.04.2015,12:53:25,$CRX:high_band_max=863MHz
23.04.2015,12:53:25,$CRX:Idle=0x
23.04.2015,12:53:25,$CRX:ChargePump=On
23.04.2015,12:53:25,$HST:CD1316LV/IV detected
23.04.2015,12:53:25,$CRX:Debug=Off
23.04.2015,12:53:25,$CRX:Trigger=Extern
23.04.2015,12:53:25,$CRX:FPUcodex=0
23.04.2015,12:53:25,$CRX:GS =13
23.04.2015,12:53:25,$CRX:GA =624
23.04.2015,12:53:25,$CRX:Delay=0msec
23.04.2015,12:53:25,$CRX:Frequency=45.0MHz
23.04.2015,12:53:25,$HST:Receiver connected
23.04.2015,12:53:25,$CRX:Sweeplength=200
23.04.2015,12:53:25,$CRX:low_band_max=171MHz
23.04.2015,12:53:25,$CRX:mid_band_max=450MHz
23.04.2015,12:53:25,$CRX:high_band_max=863MHz
23.04.2015,12:53:25,$CRX:Idle=0x
23.04.2015,12:53:27,$HST:Auto stop due to data loss.
23.04.2015,12:53:28,$HST:Measurement stop
23.04.2015,12:53:28,$HST:Measurement wait...
23.04.2015,12:53:28,$HST:Measurement halted
23.04.2015,12:53:29,$HST:Measurement idle
23.04.2015,12:53:29,$CRX:Stopped
23.04.2015,12:53:29,$HST:Measurement enable
23.04.2015,12:53:29,$CRX:AGC gain = 1.57V
23.04.2015,12:53:29,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:53:29,$CRX:Analog Input = 9.24
23.04.2015,12:53:30,$HST:Check RS232-connection!
23.04.2015,12:53:33,$HST:Attempting Auto-Start
23.04.2015,12:53:33,$HST:Param. RCU due to START
23.04.2015,12:53:33,$HST:Actual focuscode 02
23.04.2015,12:53:34,$HST:Enable data transfer
23.04.2015,12:53:34,$HST:Receiver calibration
23.04.2015,12:53:34,$CRX:Started
23.04.2015,12:53:34,$HST:Start new FITS-file
23.04.2015,12:53:34,$HST:Continous measurement
23.04.2015,12:53:36,$CRX:e-Callisto ETH Zurich
23.04.2015,12:53:36,$HST:Watchdog triggered -> Reset
23.04.2015,12:53:36,$CRX:V1.5, 2006-11-04
23.04.2015,12:53:36,$CRX:ChargePump=On
23.04.2015,12:53:36,$HST:CD1316LV/IV detected
23.04.2015,12:53:36,$CRX:Debug=Off
23.04.2015,12:53:36,$CRX:Trigger=No
23.04.2015,12:53:36,$CRX:FPUcodex=0
23.04.2015,12:53:36,$CRX:GS =13
23.04.2015,12:53:36,$CRX:GA =253
23.04.2015,12:53:36,$CRX:Delay=0msec
23.04.2015,12:53:36,$CRX:Frequency=0.0MHz
23.04.2015,12:53:36,$HST:Receiver connected
23.04.2015,12:53:36,$CRX:Sweeplength=0
23.04.2015,12:53:36,$CRX:low_band_max=171MHz
23.04.2015,12:53:36,$CRX:mid_band_max=450MHz
23.04.2015,12:53:36,$CRX:high_band_max=863MHz
23.04.2015,12:53:36,$CRX:Idle=0x
23.04.2015,12:53:36,$CRX:ChargePump=On
23.04.2015,12:53:36,$HST:CD1316LV/IV detected
23.04.2015,12:53:36,$CRX:Debug=Off
23.04.2015,12:53:36,$CRX:Trigger=Extern
23.04.2015,12:53:36,$CRX:FPUcodex=0
23.04.2015,12:53:36,$CRX:GS =13
23.04.2015,12:53:36,$CRX:GA =624
23.04.2015,12:53:36,$CRX:Delay=0msec
23.04.2015,12:53:36,$CRX:Frequency=45.0MHz
23.04.2015,12:53:36,$HST:Receiver connected
23.04.2015,12:53:36,$CRX:Sweeplength=200
23.04.2015,12:53:36,$CRX:low_band_max=171MHz
23.04.2015,12:53:36,$CRX:mid_band_max=450MHz
23.04.2015,12:53:36,$CRX:high_band_max=863MHz
23.04.2015,12:53:36,$CRX:Idle=0x
23.04.2015,12:53:39,$HST:Auto stop due to data loss.
23.04.2015,12:53:39,$HST:Measurement stop
23.04.2015,12:53:39,$HST:Measurement wait...
23.04.2015,12:53:40,$HST:Measurement halted
23.04.2015,12:53:40,$HST:Measurement idle
23.04.2015,12:53:40,$CRX:Stopped
23.04.2015,12:53:40,$HST:Measurement enable
23.04.2015,12:53:40,$CRX:AGC gain = 1.56V
23.04.2015,12:53:40,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:53:40,$CRX:Analog Input = 9.24
23.04.2015,12:53:42,$HST:Check RS232-connection!
23.04.2015,12:53:45,$HST:Attempting Auto-Start
23.04.2015,12:53:45,$HST:Param. RCU due to START
23.04.2015,12:53:45,$HST:Actual focuscode 02
23.04.2015,12:53:45,$HST:Enable data transfer
23.04.2015,12:53:45,$HST:Receiver calibration
23.04.2015,12:53:45,$CRX:Started
23.04.2015,12:53:45,$HST:Start new FITS-file
23.04.2015,12:53:45,$HST:Continous measurement
23.04.2015,12:53:47,$CRX:e-Callisto ETH Zurich
23.04.2015,12:53:47,$HST:Watchdog triggered -> Reset
23.04.2015,12:53:47,$CRX:V1.5, 2006-11-04
23.04.2015,12:53:47,$CRX:ChargePump=On
23.04.2015,12:53:47,$HST:CD1316LV/IV detected
23.04.2015,12:53:47,$CRX:Debug=Off
23.04.2015,12:53:47,$CRX:Trigger=No
23.04.2015,12:53:47,$CRX:FPUcodex=0
23.04.2015,12:53:47,$CRX:GS =13
23.04.2015,12:53:47,$CRX:GA =253
23.04.2015,12:53:47,$CRX:Delay=0msec
23.04.2015,12:53:47,$CRX:Frequency=0.0MHz
23.04.2015,12:53:47,$HST:Receiver connected
23.04.2015,12:53:47,$CRX:Sweeplength=0
23.04.2015,12:53:47,$CRX:low_band_max=171MHz
23.04.2015,12:53:47,$CRX:mid_band_max=450MHz
23.04.2015,12:53:47,$CRX:high_band_max=863MHz
23.04.2015,12:53:47,$CRX:Idle=0x
23.04.2015,12:53:47,$CRX:ChargePump=On
23.04.2015,12:53:47,$HST:CD1316LV/IV detected
23.04.2015,12:53:47,$CRX:Debug=Off
23.04.2015,12:53:47,$CRX:Trigger=Extern
23.04.2015,12:53:47,$CRX:FPUcodex=0
23.04.2015,12:53:47,$CRX:GS =13
23.04.2015,12:53:47,$CRX:GA =624
23.04.2015,12:53:47,$CRX:Delay=0msec
23.04.2015,12:53:47,$CRX:Frequency=45.0MHz
23.04.2015,12:53:47,$HST:Receiver connected
23.04.2015,12:53:47,$CRX:Sweeplength=200
23.04.2015,12:53:47,$CRX:low_band_max=171MHz
23.04.2015,12:53:47,$CRX:mid_band_max=450MHz
23.04.2015,12:53:47,$CRX:high_band_max=863MHz
23.04.2015,12:53:47,$CRX:Idle=0x
23.04.2015,12:53:50,$HST:Auto stop due to data loss.
23.04.2015,12:53:50,$HST:Measurement stop
23.04.2015,12:53:51,$HST:Measurement wait...
23.04.2015,12:53:51,$HST:Measurement halted
23.04.2015,12:53:51,$HST:Measurement idle
23.04.2015,12:53:51,$CRX:Stopped
23.04.2015,12:53:52,$HST:Measurement enable
23.04.2015,12:53:52,$CRX:AGC gain = 1.57V
23.04.2015,12:53:52,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:53:52,$CRX:Analog Input = 9.24
23.04.2015,12:53:53,$HST:Check RS232-connection!
23.04.2015,12:53:56,$HST:Attempting Auto-Start
23.04.2015,12:53:56,$HST:Param. RCU due to START
23.04.2015,12:53:56,$HST:Actual focuscode 02
23.04.2015,12:53:57,$HST:Enable data transfer
23.04.2015,12:53:57,$HST:Receiver calibration
23.04.2015,12:53:57,$CRX:Started
23.04.2015,12:53:57,$HST:Start new FITS-file
23.04.2015,12:53:57,$HST:Continous measurement
23.04.2015,12:53:59,$CRX:e-Callisto ETH Zurich
23.04.2015,12:53:59,$HST:Watchdog triggered -> Reset
23.04.2015,12:53:59,$CRX:V1.5, 2006-11-04
23.04.2015,12:53:59,$CRX:ChargePump=On
23.04.2015,12:53:59,$HST:CD1316LV/IV detected
23.04.2015,12:53:59,$CRX:Debug=Off
23.04.2015,12:53:59,$CRX:Trigger=No
23.04.2015,12:53:59,$CRX:FPUcodex=0
23.04.2015,12:53:59,$CRX:GS =13
23.04.2015,12:53:59,$CRX:GA =253
23.04.2015,12:53:59,$CRX:Delay=0msec
23.04.2015,12:53:59,$CRX:Frequency=0.0MHz
23.04.2015,12:53:59,$HST:Receiver connected
23.04.2015,12:53:59,$CRX:Sweeplength=0
23.04.2015,12:53:59,$CRX:low_band_max=171MHz
23.04.2015,12:53:59,$CRX:mid_band_max=450MHz
23.04.2015,12:53:59,$CRX:high_band_max=863MHz
23.04.2015,12:53:59,$CRX:Idle=0x
23.04.2015,12:53:59,$CRX:ChargePump=On
23.04.2015,12:53:59,$HST:CD1316LV/IV detected
23.04.2015,12:53:59,$CRX:Debug=Off
23.04.2015,12:53:59,$CRX:Trigger=Extern
23.04.2015,12:53:59,$CRX:FPUcodex=0
23.04.2015,12:53:59,$CRX:GS =13
23.04.2015,12:53:59,$CRX:GA =624
23.04.2015,12:53:59,$CRX:Delay=0msec
23.04.2015,12:53:59,$CRX:Frequency=45.0MHz
23.04.2015,12:53:59,$HST:Receiver connected
23.04.2015,12:53:59,$CRX:Sweeplength=200
23.04.2015,12:53:59,$CRX:low_band_max=171MHz
23.04.2015,12:53:59,$CRX:mid_band_max=450MHz
23.04.2015,12:53:59,$CRX:high_band_max=863MHz
23.04.2015,12:53:59,$CRX:Idle=0x
23.04.2015,12:54:02,$HST:Auto stop due to data loss.
23.04.2015,12:54:02,$HST:Measurement stop
23.04.2015,12:54:02,$HST:Measurement wait...
23.04.2015,12:54:03,$HST:Measurement halted
23.04.2015,12:54:03,$HST:Measurement idle
23.04.2015,12:54:03,$CRX:Stopped
23.04.2015,12:54:03,$HST:Measurement enable
23.04.2015,12:54:03,$CRX:AGC gain = 1.56V
23.04.2015,12:54:03,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:54:03,$CRX:Analog Input = 9.24
23.04.2015,12:54:05,$HST:Check RS232-connection!
23.04.2015,12:54:08,$HST:Attempting Auto-Start
23.04.2015,12:54:08,$HST:Param. RCU due to START
23.04.2015,12:54:08,$HST:Actual focuscode 02
23.04.2015,12:54:08,$HST:Enable data transfer
23.04.2015,12:54:08,$HST:Receiver calibration
23.04.2015,12:54:08,$CRX:Started
23.04.2015,12:54:08,$HST:Start new FITS-file
23.04.2015,12:54:08,$HST:Continous measurement
23.04.2015,12:54:10,$CRX:e-Callisto ETH Zurich
23.04.2015,12:54:10,$HST:Watchdog triggered -> Reset
23.04.2015,12:54:10,$CRX:V1.5, 2006-11-04
23.04.2015,12:54:10,$CRX:ChargePump=On
23.04.2015,12:54:10,$HST:CD1316LV/IV detected
23.04.2015,12:54:10,$CRX:Debug=Off
23.04.2015,12:54:10,$CRX:Trigger=No
23.04.2015,12:54:10,$CRX:FPUcodex=0
23.04.2015,12:54:10,$CRX:GS =13
23.04.2015,12:54:10,$CRX:GA =253
23.04.2015,12:54:10,$CRX:Delay=0msec
23.04.2015,12:54:10,$CRX:Frequency=0.0MHz
23.04.2015,12:54:10,$HST:Receiver connected
23.04.2015,12:54:10,$CRX:Sweeplength=0
23.04.2015,12:54:10,$CRX:low_band_max=171MHz
23.04.2015,12:54:10,$CRX:mid_band_max=450MHz
23.04.2015,12:54:10,$CRX:high_band_max=863MHz
23.04.2015,12:54:10,$CRX:Idle=0x
23.04.2015,12:54:10,$CRX:ChargePump=On
23.04.2015,12:54:10,$HST:CD1316LV/IV detected
23.04.2015,12:54:10,$CRX:Debug=Off
23.04.2015,12:54:10,$CRX:Trigger=Extern
23.04.2015,12:54:10,$CRX:FPUcodex=0
23.04.2015,12:54:10,$CRX:GS =13
23.04.2015,12:54:10,$CRX:GA =624
23.04.2015,12:54:10,$CRX:Delay=0msec
23.04.2015,12:54:10,$CRX:Frequency=45.0MHz
23.04.2015,12:54:10,$HST:Receiver connected
23.04.2015,12:54:10,$CRX:Sweeplength=200
23.04.2015,12:54:10,$CRX:low_band_max=171MHz
23.04.2015,12:54:10,$CRX:mid_band_max=450MHz
23.04.2015,12:54:10,$CRX:high_band_max=863MHz
23.04.2015,12:54:10,$CRX:Idle=0x
23.04.2015,12:54:13,$HST:Auto stop due to data loss.
23.04.2015,12:54:13,$HST:Measurement stop
23.04.2015,12:54:13,$HST:Measurement wait...
23.04.2015,12:54:14,$HST:Measurement halted
23.04.2015,12:54:14,$HST:Measurement idle
23.04.2015,12:54:14,$CRX:Stopped
23.04.2015,12:54:14,$HST:Measurement enable
23.04.2015,12:54:14,$CRX:AGC gain = 1.57V
23.04.2015,12:54:14,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:54:14,$CRX:Analog Input = 9.24
23.04.2015,12:54:16,$HST:Check RS232-connection!
23.04.2015,12:54:19,$HST:Attempting Auto-Start
23.04.2015,12:54:19,$HST:Param. RCU due to START
23.04.2015,12:54:19,$HST:Actual focuscode 02
23.04.2015,12:54:19,$HST:Enable data transfer
23.04.2015,12:54:19,$HST:Receiver calibration
23.04.2015,12:54:19,$CRX:Started
23.04.2015,12:54:20,$HST:Start new FITS-file
23.04.2015,12:54:20,$HST:Continous measurement
23.04.2015,12:54:21,$CRX:e-Callisto ETH Zurich
23.04.2015,12:54:21,$HST:Watchdog triggered -> Reset
23.04.2015,12:54:21,$CRX:V1.5, 2006-11-04
23.04.2015,12:54:22,$CRX:ChargePump=On
23.04.2015,12:54:22,$HST:CD1316LV/IV detected
23.04.2015,12:54:22,$CRX:Debug=Off
23.04.2015,12:54:22,$CRX:Trigger=No
23.04.2015,12:54:22,$CRX:FPUcodex=0
23.04.2015,12:54:22,$CRX:GS =13
23.04.2015,12:54:22,$CRX:GA =253
23.04.2015,12:54:22,$CRX:Delay=0msec
23.04.2015,12:54:22,$CRX:Frequency=0.0MHz
23.04.2015,12:54:22,$HST:Receiver connected
23.04.2015,12:54:22,$CRX:Sweeplength=0
23.04.2015,12:54:22,$CRX:low_band_max=171MHz
23.04.2015,12:54:22,$CRX:mid_band_max=450MHz
23.04.2015,12:54:22,$CRX:high_band_max=863MHz
23.04.2015,12:54:22,$CRX:Idle=0x
23.04.2015,12:54:22,$CRX:ChargePump=On
23.04.2015,12:54:22,$HST:CD1316LV/IV detected
23.04.2015,12:54:22,$CRX:Debug=Off
23.04.2015,12:54:22,$CRX:Trigger=Extern
23.04.2015,12:54:22,$CRX:FPUcodex=0
23.04.2015,12:54:22,$CRX:GS =13
23.04.2015,12:54:22,$CRX:GA =624
23.04.2015,12:54:22,$CRX:Delay=0msec
23.04.2015,12:54:22,$CRX:Frequency=45.0MHz
23.04.2015,12:54:22,$HST:Receiver connected
23.04.2015,12:54:22,$CRX:Sweeplength=200
23.04.2015,12:54:22,$CRX:low_band_max=171MHz
23.04.2015,12:54:22,$CRX:mid_band_max=450MHz
23.04.2015,12:54:22,$CRX:high_band_max=863MHz
23.04.2015,12:54:22,$CRX:Idle=0x
23.04.2015,12:54:24,$HST:Auto stop due to data loss.
23.04.2015,12:54:25,$HST:Measurement stop
23.04.2015,12:54:25,$HST:Measurement wait...
23.04.2015,12:54:26,$HST:Measurement halted
23.04.2015,12:54:26,$HST:Measurement idle
23.04.2015,12:54:26,$CRX:Stopped
23.04.2015,12:54:26,$HST:Measurement enable
23.04.2015,12:54:26,$CRX:AGC gain = 1.56V
23.04.2015,12:54:26,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:54:26,$CRX:Analog Input = 9.24
23.04.2015,12:54:27,$HST:Check RS232-connection!
23.04.2015,12:54:30,$HST:Attempting Auto-Start
23.04.2015,12:54:31,$HST:Param. RCU due to START
23.04.2015,12:54:31,$HST:Actual focuscode 02
23.04.2015,12:54:31,$HST:Enable data transfer
23.04.2015,12:54:31,$HST:Receiver calibration
23.04.2015,12:54:31,$CRX:Started
23.04.2015,12:54:31,$HST:Start new FITS-file
23.04.2015,12:54:31,$HST:Continous measurement
23.04.2015,12:54:33,$CRX:e-Callisto ETH Zurich
23.04.2015,12:54:33,$HST:Watchdog triggered -> Reset
23.04.2015,12:54:33,$CRX:V1.5, 2006-11-04
23.04.2015,12:54:33,$CRX:ChargePump=On
23.04.2015,12:54:33,$HST:CD1316LV/IV detected
23.04.2015,12:54:33,$CRX:Debug=Off
23.04.2015,12:54:33,$CRX:Trigger=No
23.04.2015,12:54:33,$CRX:FPUcodex=0
23.04.2015,12:54:33,$CRX:GS =13
23.04.2015,12:54:33,$CRX:GA =253
23.04.2015,12:54:33,$CRX:Delay=0msec
23.04.2015,12:54:33,$CRX:Frequency=0.0MHz
23.04.2015,12:54:33,$HST:Receiver connected
23.04.2015,12:54:33,$CRX:Sweeplength=0
23.04.2015,12:54:33,$CRX:low_band_max=171MHz
23.04.2015,12:54:33,$CRX:mid_band_max=450MHz
23.04.2015,12:54:33,$CRX:high_band_max=863MHz
23.04.2015,12:54:33,$CRX:Idle=0x
23.04.2015,12:54:33,$CRX:ChargePump=On
23.04.2015,12:54:33,$HST:CD1316LV/IV detected
23.04.2015,12:54:33,$CRX:Debug=Off
23.04.2015,12:54:33,$CRX:Trigger=Extern
23.04.2015,12:54:33,$CRX:FPUcodex=0
23.04.2015,12:54:33,$CRX:GS =13
23.04.2015,12:54:33,$CRX:GA =624
23.04.2015,12:54:33,$CRX:Delay=0msec
23.04.2015,12:54:33,$CRX:Frequency=45.0MHz
23.04.2015,12:54:33,$HST:Receiver connected
23.04.2015,12:54:33,$CRX:Sweeplength=200
23.04.2015,12:54:33,$CRX:low_band_max=171MHz
23.04.2015,12:54:33,$CRX:mid_band_max=450MHz
23.04.2015,12:54:33,$CRX:high_band_max=863MHz
23.04.2015,12:54:33,$CRX:Idle=0x
23.04.2015,12:54:36,$HST:Auto stop due to data loss.
23.04.2015,12:54:36,$HST:Measurement stop
23.04.2015,12:54:36,$HST:Measurement wait...
23.04.2015,12:54:37,$HST:Measurement halted
23.04.2015,12:54:37,$HST:Measurement idle
23.04.2015,12:54:37,$CRX:Stopped
23.04.2015,12:54:37,$HST:Measurement enable
23.04.2015,12:54:37,$CRX:AGC gain = 1.57V
23.04.2015,12:54:37,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:54:37,$CRX:Analog Input = 9.24
23.04.2015,12:54:39,$HST:Check RS232-connection!
23.04.2015,12:54:42,$HST:Attempting Auto-Start
23.04.2015,12:54:42,$HST:Param. RCU due to START
23.04.2015,12:54:42,$HST:Actual focuscode 02
23.04.2015,12:54:42,$HST:Enable data transfer
23.04.2015,12:54:42,$HST:Receiver calibration
23.04.2015,12:54:42,$CRX:Started
23.04.2015,12:54:42,$HST:Start new FITS-file
23.04.2015,12:54:43,$HST:Continous measurement
23.04.2015,12:54:44,$CRX:e-Callisto ETH Zurich
23.04.2015,12:54:44,$HST:Watchdog triggered -> Reset
23.04.2015,12:54:44,$CRX:V1.5, 2006-11-04
23.04.2015,12:54:44,$CRX:ChargePump=On
23.04.2015,12:54:44,$HST:CD1316LV/IV detected
23.04.2015,12:54:44,$CRX:Debug=Off
23.04.2015,12:54:44,$CRX:Trigger=No
23.04.2015,12:54:44,$CRX:FPUcodex=0
23.04.2015,12:54:44,$CRX:GS =13
23.04.2015,12:54:44,$CRX:GA =253
23.04.2015,12:54:44,$CRX:Delay=0msec
23.04.2015,12:54:44,$CRX:Frequency=0.0MHz
23.04.2015,12:54:44,$HST:Receiver connected
23.04.2015,12:54:44,$CRX:Sweeplength=0
23.04.2015,12:54:44,$CRX:low_band_max=171MHz
23.04.2015,12:54:44,$CRX:mid_band_max=450MHz
23.04.2015,12:54:44,$CRX:high_band_max=863MHz
23.04.2015,12:54:44,$CRX:Idle=0x
23.04.2015,12:54:44,$CRX:ChargePump=On
23.04.2015,12:54:44,$HST:CD1316LV/IV detected
23.04.2015,12:54:44,$CRX:Debug=Off
23.04.2015,12:54:44,$CRX:Trigger=Extern
23.04.2015,12:54:44,$CRX:FPUcodex=0
23.04.2015,12:54:44,$CRX:GS =13
23.04.2015,12:54:44,$CRX:GA =624
23.04.2015,12:54:44,$CRX:Delay=0msec
23.04.2015,12:54:44,$CRX:Frequency=45.0MHz
23.04.2015,12:54:44,$HST:Receiver connected
23.04.2015,12:54:44,$CRX:Sweeplength=200
23.04.2015,12:54:44,$CRX:low_band_max=171MHz
23.04.2015,12:54:44,$CRX:mid_band_max=450MHz
23.04.2015,12:54:44,$CRX:high_band_max=863MHz
23.04.2015,12:54:44,$CRX:Idle=0x
23.04.2015,12:54:47,$HST:Auto stop due to data loss.
23.04.2015,12:54:47,$HST:Measurement stop
23.04.2015,12:54:48,$HST:Measurement wait...
23.04.2015,12:54:48,$HST:Measurement halted
23.04.2015,12:54:49,$HST:Measurement idle
23.04.2015,12:54:49,$CRX:Stopped
23.04.2015,12:54:49,$HST:Measurement enable
23.04.2015,12:54:49,$CRX:AGC gain = 1.56V
23.04.2015,12:54:49,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:54:49,$CRX:Analog Input = 9.24
23.04.2015,12:54:50,$HST:Check RS232-connection!
23.04.2015,12:54:53,$HST:Attempting Auto-Start
23.04.2015,12:54:53,$HST:Param. RCU due to START
23.04.2015,12:54:53,$HST:Actual focuscode 02
23.04.2015,12:54:54,$HST:Enable data transfer
23.04.2015,12:54:54,$HST:Receiver calibration
23.04.2015,12:54:54,$CRX:Started
23.04.2015,12:54:54,$HST:Start new FITS-file
23.04.2015,12:54:54,$HST:Continous measurement
23.04.2015,12:54:56,$CRX:e-Callisto ETH Zurich
23.04.2015,12:54:56,$HST:Watchdog triggered -> Reset
23.04.2015,12:54:56,$CRX:V1.5, 2006-11-04
23.04.2015,12:54:56,$CRX:ChargePump=On
23.04.2015,12:54:56,$HST:CD1316LV/IV detected
23.04.2015,12:54:56,$CRX:Debug=Off
23.04.2015,12:54:56,$CRX:Trigger=No
23.04.2015,12:54:56,$CRX:FPUcodex=0
23.04.2015,12:54:56,$CRX:GS =13
23.04.2015,12:54:56,$CRX:GA =253
23.04.2015,12:54:56,$CRX:Delay=0msec
23.04.2015,12:54:56,$CRX:Frequency=0.0MHz
23.04.2015,12:54:56,$HST:Receiver connected
23.04.2015,12:54:56,$CRX:Sweeplength=0
23.04.2015,12:54:56,$CRX:low_band_max=171MHz
23.04.2015,12:54:56,$CRX:mid_band_max=450MHz
23.04.2015,12:54:56,$CRX:high_band_max=863MHz
23.04.2015,12:54:56,$CRX:Idle=0x
23.04.2015,12:54:56,$CRX:ChargePump=On
23.04.2015,12:54:56,$HST:CD1316LV/IV detected
23.04.2015,12:54:56,$CRX:Debug=Off
23.04.2015,12:54:56,$CRX:Trigger=Extern
23.04.2015,12:54:56,$CRX:FPUcodex=0
23.04.2015,12:54:56,$CRX:GS =13
23.04.2015,12:54:56,$CRX:GA =624
23.04.2015,12:54:56,$CRX:Delay=0msec
23.04.2015,12:54:56,$CRX:Frequency=45.0MHz
23.04.2015,12:54:56,$HST:Receiver connected
23.04.2015,12:54:56,$CRX:Sweeplength=200
23.04.2015,12:54:56,$CRX:low_band_max=171MHz
23.04.2015,12:54:56,$CRX:mid_band_max=450MHz
23.04.2015,12:54:56,$CRX:high_band_max=863MHz
23.04.2015,12:54:56,$CRX:Idle=0x
23.04.2015,12:54:59,$HST:Auto stop due to data loss.
23.04.2015,12:54:59,$HST:Measurement stop
23.04.2015,12:54:59,$HST:Measurement wait...
23.04.2015,12:55:00,$HST:Measurement halted
23.04.2015,12:55:00,$HST:Measurement idle
23.04.2015,12:55:00,$CRX:Stopped
23.04.2015,12:55:00,$HST:Measurement enable
23.04.2015,12:55:00,$CRX:AGC gain = 1.57V
23.04.2015,12:55:00,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:55:00,$CRX:Analog Input = 9.24
23.04.2015,12:55:02,$HST:Check RS232-connection!
23.04.2015,12:55:05,$HST:Attempting Auto-Start
23.04.2015,12:55:05,$HST:Param. RCU due to START
23.04.2015,12:55:05,$HST:Actual focuscode 02
23.04.2015,12:55:05,$HST:Enable data transfer
23.04.2015,12:55:05,$HST:Receiver calibration
23.04.2015,12:55:05,$CRX:Started
23.04.2015,12:55:05,$HST:Start new FITS-file
23.04.2015,12:55:05,$HST:Continous measurement
23.04.2015,12:55:07,$CRX:e-Callisto ETH Zurich
23.04.2015,12:55:07,$HST:Watchdog triggered -> Reset
23.04.2015,12:55:07,$CRX:V1.5, 2006-11-04
23.04.2015,12:55:07,$CRX:ChargePump=On
23.04.2015,12:55:07,$HST:CD1316LV/IV detected
23.04.2015,12:55:07,$CRX:Debug=Off
23.04.2015,12:55:07,$CRX:Trigger=No
23.04.2015,12:55:07,$CRX:FPUcodex=0
23.04.2015,12:55:07,$CRX:GS =13
23.04.2015,12:55:07,$CRX:GA =253
23.04.2015,12:55:07,$CRX:Delay=0msec
23.04.2015,12:55:07,$CRX:Frequency=0.0MHz
23.04.2015,12:55:07,$HST:Receiver connected
23.04.2015,12:55:07,$CRX:Sweeplength=0
23.04.2015,12:55:07,$CRX:low_band_max=171MHz
23.04.2015,12:55:07,$CRX:mid_band_max=450MHz
23.04.2015,12:55:07,$CRX:high_band_max=863MHz
23.04.2015,12:55:07,$CRX:Idle=0x
23.04.2015,12:55:07,$CRX:ChargePump=On
23.04.2015,12:55:07,$HST:CD1316LV/IV detected
23.04.2015,12:55:07,$CRX:Debug=Off
23.04.2015,12:55:07,$CRX:Trigger=Extern
23.04.2015,12:55:07,$CRX:FPUcodex=0
23.04.2015,12:55:07,$CRX:GS =13
23.04.2015,12:55:07,$CRX:GA =624
23.04.2015,12:55:07,$CRX:Delay=0msec
23.04.2015,12:55:07,$CRX:Frequency=45.0MHz
23.04.2015,12:55:07,$HST:Receiver connected
23.04.2015,12:55:07,$CRX:Sweeplength=200
23.04.2015,12:55:07,$CRX:low_band_max=171MHz
23.04.2015,12:55:07,$CRX:mid_band_max=450MHz
23.04.2015,12:55:07,$CRX:high_band_max=863MHz
23.04.2015,12:55:07,$CRX:Idle=0x
23.04.2015,12:55:10,$HST:Auto stop due to data loss.
23.04.2015,12:55:10,$HST:Measurement stop
23.04.2015,12:55:10,$HST:Measurement wait...
23.04.2015,12:55:11,$HST:Measurement halted
23.04.2015,12:55:11,$HST:Measurement idle
23.04.2015,12:55:11,$CRX:Stopped
23.04.2015,12:55:12,$HST:Measurement enable
23.04.2015,12:55:12,$CRX:AGC gain = 1.56V
23.04.2015,12:55:12,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:55:12,$CRX:Analog Input = 9.24
23.04.2015,12:55:13,$HST:Check RS232-connection!
23.04.2015,12:55:16,$HST:Attempting Auto-Start
23.04.2015,12:55:16,$HST:Param. RCU due to START
23.04.2015,12:55:16,$HST:Actual focuscode 02
23.04.2015,12:55:16,$HST:Enable data transfer
23.04.2015,12:55:16,$HST:Receiver calibration
23.04.2015,12:55:16,$CRX:Started
23.04.2015,12:55:17,$HST:Start new FITS-file
23.04.2015,12:55:17,$HST:Continous measurement
23.04.2015,12:55:19,$CRX:e-Callisto ETH Zurich
23.04.2015,12:55:19,$HST:Watchdog triggered -> Reset
23.04.2015,12:55:19,$CRX:V1.5, 2006-11-04
23.04.2015,12:55:19,$CRX:ChargePump=On
23.04.2015,12:55:19,$HST:CD1316LV/IV detected
23.04.2015,12:55:19,$CRX:Debug=Off
23.04.2015,12:55:19,$CRX:Trigger=No
23.04.2015,12:55:19,$CRX:FPUcodex=0
23.04.2015,12:55:19,$CRX:GS =13
23.04.2015,12:55:19,$CRX:GA =253
23.04.2015,12:55:19,$CRX:Delay=0msec
23.04.2015,12:55:19,$CRX:Frequency=0.0MHz
23.04.2015,12:55:19,$HST:Receiver connected
23.04.2015,12:55:19,$CRX:Sweeplength=0
23.04.2015,12:55:19,$CRX:low_band_max=171MHz
23.04.2015,12:55:19,$CRX:mid_band_max=450MHz
23.04.2015,12:55:19,$CRX:high_band_max=863MHz
23.04.2015,12:55:19,$CRX:Idle=0x
23.04.2015,12:55:19,$CRX:ChargePump=On
23.04.2015,12:55:19,$HST:CD1316LV/IV detected
23.04.2015,12:55:19,$CRX:Debug=Off
23.04.2015,12:55:19,$CRX:Trigger=Extern
23.04.2015,12:55:19,$CRX:FPUcodex=0
23.04.2015,12:55:19,$CRX:GS =13
23.04.2015,12:55:19,$CRX:GA =624
23.04.2015,12:55:19,$CRX:Delay=0msec
23.04.2015,12:55:19,$CRX:Frequency=45.0MHz
23.04.2015,12:55:19,$HST:Receiver connected
23.04.2015,12:55:19,$CRX:Sweeplength=200
23.04.2015,12:55:19,$CRX:low_band_max=171MHz
23.04.2015,12:55:19,$CRX:mid_band_max=450MHz
23.04.2015,12:55:19,$CRX:high_band_max=863MHz
23.04.2015,12:55:19,$CRX:Idle=0x
23.04.2015,12:55:22,$HST:Auto stop due to data loss.
23.04.2015,12:55:22,$HST:Measurement stop
23.04.2015,12:55:22,$HST:Measurement wait...
23.04.2015,12:55:23,$HST:Measurement halted
23.04.2015,12:55:23,$HST:Measurement idle
23.04.2015,12:55:23,$CRX:Stopped
23.04.2015,12:55:23,$HST:Measurement enable
23.04.2015,12:55:23,$CRX:AGC gain = 1.57V
23.04.2015,12:55:23,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:55:23,$CRX:Analog Input = 9.24
23.04.2015,12:55:25,$HST:Check RS232-connection!
23.04.2015,12:55:28,$HST:Attempting Auto-Start
23.04.2015,12:55:28,$HST:Param. RCU due to START
23.04.2015,12:55:28,$HST:Actual focuscode 02
23.04.2015,12:55:28,$HST:Enable data transfer
23.04.2015,12:55:28,$HST:Receiver calibration
23.04.2015,12:55:28,$CRX:Started
23.04.2015,12:55:28,$HST:Start new FITS-file
23.04.2015,12:55:28,$HST:Continous measurement
23.04.2015,12:55:30,$CRX:e-Callisto ETH Zurich
23.04.2015,12:55:30,$HST:Watchdog triggered -> Reset
23.04.2015,12:55:30,$CRX:V1.5, 2006-11-04
23.04.2015,12:55:30,$CRX:ChargePump=On
23.04.2015,12:55:30,$HST:CD1316LV/IV detected
23.04.2015,12:55:30,$CRX:Debug=Off
23.04.2015,12:55:30,$CRX:Trigger=No
23.04.2015,12:55:30,$CRX:FPUcodex=0
23.04.2015,12:55:30,$CRX:GS =13
23.04.2015,12:55:30,$CRX:GA =253
23.04.2015,12:55:30,$CRX:Delay=0msec
23.04.2015,12:55:30,$CRX:Frequency=0.0MHz
23.04.2015,12:55:30,$HST:Receiver connected
23.04.2015,12:55:30,$CRX:Sweeplength=0
23.04.2015,12:55:30,$CRX:low_band_max=171MHz
23.04.2015,12:55:30,$CRX:mid_band_max=450MHz
23.04.2015,12:55:30,$CRX:high_band_max=863MHz
23.04.2015,12:55:30,$CRX:Idle=0x
23.04.2015,12:55:30,$CRX:ChargePump=On
23.04.2015,12:55:30,$HST:CD1316LV/IV detected
23.04.2015,12:55:30,$CRX:Debug=Off
23.04.2015,12:55:30,$CRX:Trigger=Extern
23.04.2015,12:55:30,$CRX:FPUcodex=0
23.04.2015,12:55:30,$CRX:GS =13
23.04.2015,12:55:30,$CRX:GA =624
23.04.2015,12:55:30,$CRX:Delay=0msec
23.04.2015,12:55:30,$CRX:Frequency=45.0MHz
23.04.2015,12:55:30,$HST:Receiver connected
23.04.2015,12:55:30,$CRX:Sweeplength=200
23.04.2015,12:55:30,$CRX:low_band_max=171MHz
23.04.2015,12:55:30,$CRX:mid_band_max=450MHz
23.04.2015,12:55:30,$CRX:high_band_max=863MHz
23.04.2015,12:55:30,$CRX:Idle=0x
23.04.2015,12:55:33,$HST:Auto stop due to data loss.
23.04.2015,12:55:33,$HST:Measurement stop
23.04.2015,12:55:33,$HST:Measurement wait...
23.04.2015,12:55:34,$HST:Measurement halted
23.04.2015,12:55:34,$HST:Measurement idle
23.04.2015,12:55:34,$CRX:Stopped
23.04.2015,12:55:34,$HST:Measurement enable
23.04.2015,12:55:34,$CRX:AGC gain = 1.56V
23.04.2015,12:55:34,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:55:34,$CRX:Analog Input = 9.24
23.04.2015,12:55:36,$HST:Check RS232-connection!
23.04.2015,12:55:39,$HST:Attempting Auto-Start
23.04.2015,12:55:39,$HST:Param. RCU due to START
23.04.2015,12:55:39,$HST:Actual focuscode 02
23.04.2015,12:55:39,$HST:Enable data transfer
23.04.2015,12:55:39,$HST:Receiver calibration
23.04.2015,12:55:39,$CRX:Started
23.04.2015,12:55:39,$HST:Start new FITS-file
23.04.2015,12:55:40,$HST:Continous measurement
23.04.2015,12:55:41,$CRX:e-Callisto ETH Zurich
23.04.2015,12:55:41,$HST:Watchdog triggered -> Reset
23.04.2015,12:55:41,$CRX:V1.5, 2006-11-04
23.04.2015,12:55:42,$CRX:ChargePump=On
23.04.2015,12:55:42,$HST:CD1316LV/IV detected
23.04.2015,12:55:42,$CRX:Debug=Off
23.04.2015,12:55:42,$CRX:Trigger=No
23.04.2015,12:55:42,$CRX:FPUcodex=0
23.04.2015,12:55:42,$CRX:GS =13
23.04.2015,12:55:42,$CRX:GA =253
23.04.2015,12:55:42,$CRX:Delay=0msec
23.04.2015,12:55:42,$CRX:Frequency=0.0MHz
23.04.2015,12:55:42,$HST:Receiver connected
23.04.2015,12:55:42,$CRX:Sweeplength=0
23.04.2015,12:55:42,$CRX:low_band_max=171MHz
23.04.2015,12:55:42,$CRX:mid_band_max=450MHz
23.04.2015,12:55:42,$CRX:high_band_max=863MHz
23.04.2015,12:55:42,$CRX:Idle=0x
23.04.2015,12:55:42,$CRX:ChargePump=On
23.04.2015,12:55:42,$HST:CD1316LV/IV detected
23.04.2015,12:55:42,$CRX:Debug=Off
23.04.2015,12:55:42,$CRX:Trigger=Extern
23.04.2015,12:55:42,$CRX:FPUcodex=0
23.04.2015,12:55:42,$CRX:GS =13
23.04.2015,12:55:42,$CRX:GA =624
23.04.2015,12:55:42,$CRX:Delay=0msec
23.04.2015,12:55:42,$CRX:Frequency=45.0MHz
23.04.2015,12:55:42,$HST:Receiver connected
23.04.2015,12:55:42,$CRX:Sweeplength=200
23.04.2015,12:55:42,$CRX:low_band_max=171MHz
23.04.2015,12:55:42,$CRX:mid_band_max=450MHz
23.04.2015,12:55:42,$CRX:high_band_max=863MHz
23.04.2015,12:55:42,$CRX:Idle=0x
23.04.2015,12:55:44,$HST:Auto stop due to data loss.
23.04.2015,12:55:45,$HST:Measurement stop
23.04.2015,12:55:45,$HST:Measurement wait...
23.04.2015,12:55:45,$HST:Measurement halted
23.04.2015,12:55:46,$HST:Measurement idle
23.04.2015,12:55:46,$CRX:Stopped
23.04.2015,12:55:46,$HST:Measurement enable
23.04.2015,12:55:46,$CRX:AGC gain = 1.56V
23.04.2015,12:55:46,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:55:46,$CRX:Analog Input = 9.24
23.04.2015,12:55:47,$HST:Check RS232-connection!
23.04.2015,12:55:50,$HST:Attempting Auto-Start
23.04.2015,12:55:51,$HST:Param. RCU due to START
23.04.2015,12:55:51,$HST:Actual focuscode 02
23.04.2015,12:55:51,$HST:Enable data transfer
23.04.2015,12:55:51,$HST:Receiver calibration
23.04.2015,12:55:51,$CRX:Started
23.04.2015,12:55:51,$HST:Start new FITS-file
23.04.2015,12:55:51,$HST:Continous measurement
23.04.2015,12:55:53,$CRX:e-Callisto ETH Zurich
23.04.2015,12:55:53,$HST:Watchdog triggered -> Reset
23.04.2015,12:55:53,$CRX:V1.5, 2006-11-04
23.04.2015,12:55:53,$CRX:ChargePump=On
23.04.2015,12:55:53,$HST:CD1316LV/IV detected
23.04.2015,12:55:53,$CRX:Debug=Off
23.04.2015,12:55:53,$CRX:Trigger=No
23.04.2015,12:55:53,$CRX:FPUcodex=0
23.04.2015,12:55:53,$CRX:GS =13
23.04.2015,12:55:53,$CRX:GA =253
23.04.2015,12:55:53,$CRX:Delay=0msec
23.04.2015,12:55:53,$CRX:Frequency=0.0MHz
23.04.2015,12:55:53,$HST:Receiver connected
23.04.2015,12:55:53,$CRX:Sweeplength=0
23.04.2015,12:55:53,$CRX:low_band_max=171MHz
23.04.2015,12:55:53,$CRX:mid_band_max=450MHz
23.04.2015,12:55:53,$CRX:high_band_max=863MHz
23.04.2015,12:55:53,$CRX:Idle=0x
23.04.2015,12:55:53,$CRX:ChargePump=On
23.04.2015,12:55:53,$HST:CD1316LV/IV detected
23.04.2015,12:55:53,$CRX:Debug=Off
23.04.2015,12:55:53,$CRX:Trigger=Extern
23.04.2015,12:55:53,$CRX:FPUcodex=0
23.04.2015,12:55:53,$CRX:GS =13
23.04.2015,12:55:53,$CRX:GA =624
23.04.2015,12:55:53,$CRX:Delay=0msec
23.04.2015,12:55:53,$CRX:Frequency=45.0MHz
23.04.2015,12:55:53,$HST:Receiver connected
23.04.2015,12:55:53,$CRX:Sweeplength=200
23.04.2015,12:55:53,$CRX:low_band_max=171MHz
23.04.2015,12:55:53,$CRX:mid_band_max=450MHz
23.04.2015,12:55:53,$CRX:high_band_max=863MHz
23.04.2015,12:55:53,$CRX:Idle=0x
23.04.2015,12:55:56,$HST:Auto stop due to data loss.
23.04.2015,12:55:56,$HST:Measurement stop
23.04.2015,12:55:56,$HST:Measurement wait...
23.04.2015,12:55:57,$HST:Measurement halted
23.04.2015,12:55:57,$HST:Measurement idle
23.04.2015,12:55:57,$CRX:Stopped
23.04.2015,12:55:57,$HST:Measurement enable
23.04.2015,12:55:57,$CRX:AGC gain = 1.57V
23.04.2015,12:55:57,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:55:57,$CRX:Analog Input = 9.24
23.04.2015,12:55:59,$HST:Check RS232-connection!
23.04.2015,12:56:02,$HST:Attempting Auto-Start
23.04.2015,12:56:02,$HST:Param. RCU due to START
23.04.2015,12:56:02,$HST:Actual focuscode 02
23.04.2015,12:56:02,$HST:Enable data transfer
23.04.2015,12:56:02,$HST:Receiver calibration
23.04.2015,12:56:02,$CRX:Started
23.04.2015,12:56:02,$HST:Start new FITS-file
23.04.2015,12:56:03,$HST:Continous measurement
23.04.2015,12:56:04,$CRX:e-Callisto ETH Zurich
23.04.2015,12:56:04,$HST:Watchdog triggered -> Reset
23.04.2015,12:56:04,$CRX:V1.5, 2006-11-04
23.04.2015,12:56:04,$CRX:ChargePump=On
23.04.2015,12:56:04,$HST:CD1316LV/IV detected
23.04.2015,12:56:04,$CRX:Debug=Off
23.04.2015,12:56:04,$CRX:Trigger=No
23.04.2015,12:56:04,$CRX:FPUcodex=0
23.04.2015,12:56:04,$CRX:GS =13
23.04.2015,12:56:04,$CRX:GA =253
23.04.2015,12:56:04,$CRX:Delay=0msec
23.04.2015,12:56:04,$CRX:Frequency=0.0MHz
23.04.2015,12:56:04,$HST:Receiver connected
23.04.2015,12:56:04,$CRX:Sweeplength=0
23.04.2015,12:56:04,$CRX:low_band_max=171MHz
23.04.2015,12:56:04,$CRX:mid_band_max=450MHz
23.04.2015,12:56:04,$CRX:high_band_max=863MHz
23.04.2015,12:56:04,$CRX:Idle=0x
23.04.2015,12:56:04,$CRX:ChargePump=On
23.04.2015,12:56:04,$HST:CD1316LV/IV detected
23.04.2015,12:56:04,$CRX:Debug=Off
23.04.2015,12:56:04,$CRX:Trigger=Extern
23.04.2015,12:56:04,$CRX:FPUcodex=0
23.04.2015,12:56:04,$CRX:GS =13
23.04.2015,12:56:04,$CRX:GA =624
23.04.2015,12:56:04,$CRX:Delay=0msec
23.04.2015,12:56:04,$CRX:Frequency=45.0MHz
23.04.2015,12:56:04,$HST:Receiver connected
23.04.2015,12:56:04,$CRX:Sweeplength=200
23.04.2015,12:56:04,$CRX:low_band_max=171MHz
23.04.2015,12:56:04,$CRX:mid_band_max=450MHz
23.04.2015,12:56:04,$CRX:high_band_max=863MHz
23.04.2015,12:56:04,$CRX:Idle=0x
23.04.2015,12:56:07,$HST:Auto stop due to data loss.
23.04.2015,12:56:07,$HST:Measurement stop
23.04.2015,12:56:08,$HST:Measurement wait...
23.04.2015,12:56:08,$HST:Measurement halted
23.04.2015,12:56:08,$HST:Measurement idle
23.04.2015,12:56:08,$CRX:Stopped
23.04.2015,12:56:09,$HST:Measurement enable
23.04.2015,12:56:09,$CRX:AGC gain = 1.57V
23.04.2015,12:56:09,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:56:09,$CRX:Analog Input = 9.24
23.04.2015,12:56:10,$HST:Check RS232-connection!
23.04.2015,12:56:13,$HST:Attempting Auto-Start
23.04.2015,12:56:13,$HST:Param. RCU due to START
23.04.2015,12:56:13,$HST:Actual focuscode 02
23.04.2015,12:56:14,$HST:Enable data transfer
23.04.2015,12:56:14,$HST:Receiver calibration
23.04.2015,12:56:14,$CRX:Started
23.04.2015,12:56:14,$HST:Start new FITS-file
23.04.2015,12:56:14,$HST:Continous measurement
23.04.2015,12:56:16,$CRX:e-Callisto ETH Zurich
23.04.2015,12:56:16,$HST:Watchdog triggered -> Reset
23.04.2015,12:56:16,$CRX:V1.5, 2006-11-04
23.04.2015,12:56:16,$CRX:ChargePump=On
23.04.2015,12:56:16,$HST:CD1316LV/IV detected
23.04.2015,12:56:16,$CRX:Debug=Off
23.04.2015,12:56:16,$CRX:Trigger=No
23.04.2015,12:56:16,$CRX:FPUcodex=0
23.04.2015,12:56:16,$CRX:GS =13
23.04.2015,12:56:16,$CRX:GA =253
23.04.2015,12:56:16,$CRX:Delay=0msec
23.04.2015,12:56:16,$CRX:Frequency=0.0MHz
23.04.2015,12:56:16,$HST:Receiver connected
23.04.2015,12:56:16,$CRX:Sweeplength=0
23.04.2015,12:56:16,$CRX:low_band_max=171MHz
23.04.2015,12:56:16,$CRX:mid_band_max=450MHz
23.04.2015,12:56:16,$CRX:high_band_max=863MHz
23.04.2015,12:56:16,$CRX:Idle=0x
23.04.2015,12:56:16,$CRX:ChargePump=On
23.04.2015,12:56:16,$HST:CD1316LV/IV detected
23.04.2015,12:56:16,$CRX:Debug=Off
23.04.2015,12:56:16,$CRX:Trigger=Extern
23.04.2015,12:56:16,$CRX:FPUcodex=0
23.04.2015,12:56:16,$CRX:GS =13
23.04.2015,12:56:16,$CRX:GA =624
23.04.2015,12:56:16,$CRX:Delay=0msec
23.04.2015,12:56:16,$CRX:Frequency=45.0MHz
23.04.2015,12:56:16,$HST:Receiver connected
23.04.2015,12:56:16,$CRX:Sweeplength=200
23.04.2015,12:56:16,$CRX:low_band_max=171MHz
23.04.2015,12:56:16,$CRX:mid_band_max=450MHz
23.04.2015,12:56:16,$CRX:high_band_max=863MHz
23.04.2015,12:56:16,$CRX:Idle=0x
23.04.2015,12:56:19,$HST:Auto stop due to data loss.
23.04.2015,12:56:19,$HST:Measurement stop
23.04.2015,12:56:19,$HST:Measurement wait...
23.04.2015,12:56:20,$HST:Measurement halted
23.04.2015,12:56:20,$HST:Measurement idle
23.04.2015,12:56:20,$CRX:Stopped
23.04.2015,12:56:20,$HST:Measurement enable
23.04.2015,12:56:20,$CRX:AGC gain = 1.56V
23.04.2015,12:56:20,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:56:20,$CRX:Analog Input = 9.24
23.04.2015,12:56:22,$HST:Check RS232-connection!
23.04.2015,12:56:25,$HST:Attempting Auto-Start
23.04.2015,12:56:25,$HST:Param. RCU due to START
23.04.2015,12:56:25,$HST:Actual focuscode 02
23.04.2015,12:56:25,$HST:Enable data transfer
23.04.2015,12:56:25,$HST:Receiver calibration
23.04.2015,12:56:25,$CRX:Started
23.04.2015,12:56:25,$HST:Start new FITS-file
23.04.2015,12:56:25,$HST:Continous measurement
23.04.2015,12:56:27,$CRX:e-Callisto ETH Zurich
23.04.2015,12:56:27,$HST:Watchdog triggered -> Reset
23.04.2015,12:56:27,$CRX:V1.5, 2006-11-04
23.04.2015,12:56:27,$CRX:ChargePump=On
23.04.2015,12:56:27,$HST:CD1316LV/IV detected
23.04.2015,12:56:27,$CRX:Debug=Off
23.04.2015,12:56:27,$CRX:Trigger=No
23.04.2015,12:56:27,$CRX:FPUcodex=0
23.04.2015,12:56:27,$CRX:GS =13
23.04.2015,12:56:27,$CRX:GA =253
23.04.2015,12:56:27,$CRX:Delay=0msec
23.04.2015,12:56:27,$CRX:Frequency=0.0MHz
23.04.2015,12:56:27,$HST:Receiver connected
23.04.2015,12:56:27,$CRX:Sweeplength=0
23.04.2015,12:56:27,$CRX:low_band_max=171MHz
23.04.2015,12:56:27,$CRX:mid_band_max=450MHz
23.04.2015,12:56:27,$CRX:high_band_max=863MHz
23.04.2015,12:56:27,$CRX:Idle=0x
23.04.2015,12:56:27,$CRX:ChargePump=On
23.04.2015,12:56:27,$HST:CD1316LV/IV detected
23.04.2015,12:56:27,$CRX:Debug=Off
23.04.2015,12:56:27,$CRX:Trigger=Extern
23.04.2015,12:56:27,$CRX:FPUcodex=0
23.04.2015,12:56:27,$CRX:GS =13
23.04.2015,12:56:27,$CRX:GA =624
23.04.2015,12:56:27,$CRX:Delay=0msec
23.04.2015,12:56:27,$CRX:Frequency=45.0MHz
23.04.2015,12:56:27,$HST:Receiver connected
23.04.2015,12:56:27,$CRX:Sweeplength=200
23.04.2015,12:56:27,$CRX:low_band_max=171MHz
23.04.2015,12:56:27,$CRX:mid_band_max=450MHz
23.04.2015,12:56:27,$CRX:high_band_max=863MHz
23.04.2015,12:56:27,$CRX:Idle=0x
23.04.2015,12:56:30,$HST:Auto stop due to data loss.
23.04.2015,12:56:30,$HST:Measurement stop
23.04.2015,12:56:30,$HST:Measurement wait...
23.04.2015,12:56:31,$HST:Measurement halted
23.04.2015,12:56:31,$HST:Measurement idle
23.04.2015,12:56:31,$CRX:Stopped
23.04.2015,12:56:32,$HST:Measurement enable
23.04.2015,12:56:32,$CRX:AGC gain = 1.57V
23.04.2015,12:56:32,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:56:32,$CRX:Analog Input = 9.24
23.04.2015,12:56:33,$HST:Check RS232-connection!
23.04.2015,12:56:36,$HST:Attempting Auto-Start
23.04.2015,12:56:36,$HST:Param. RCU due to START
23.04.2015,12:56:36,$HST:Actual focuscode 02
23.04.2015,12:56:36,$HST:Enable data transfer
23.04.2015,12:56:36,$HST:Receiver calibration
23.04.2015,12:56:36,$CRX:Started
23.04.2015,12:56:37,$HST:Start new FITS-file
23.04.2015,12:56:37,$HST:Continous measurement
23.04.2015,12:56:38,$CRX:e-Callisto ETH Zurich
23.04.2015,12:56:38,$HST:Watchdog triggered -> Reset
23.04.2015,12:56:38,$CRX:V1.5, 2006-11-04
23.04.2015,12:56:39,$CRX:ChargePump=On
23.04.2015,12:56:39,$HST:CD1316LV/IV detected
23.04.2015,12:56:39,$CRX:Debug=Off
23.04.2015,12:56:39,$CRX:Trigger=No
23.04.2015,12:56:39,$CRX:FPUcodex=0
23.04.2015,12:56:39,$CRX:GS =13
23.04.2015,12:56:39,$CRX:GA =253
23.04.2015,12:56:39,$CRX:Delay=0msec
23.04.2015,12:56:39,$CRX:Frequency=0.0MHz
23.04.2015,12:56:39,$HST:Receiver connected
23.04.2015,12:56:39,$CRX:Sweeplength=0
23.04.2015,12:56:39,$CRX:low_band_max=171MHz
23.04.2015,12:56:39,$CRX:mid_band_max=450MHz
23.04.2015,12:56:39,$CRX:high_band_max=863MHz
23.04.2015,12:56:39,$CRX:Idle=0x
23.04.2015,12:56:39,$CRX:ChargePump=On
23.04.2015,12:56:39,$HST:CD1316LV/IV detected
23.04.2015,12:56:39,$CRX:Debug=Off
23.04.2015,12:56:39,$CRX:Trigger=Extern
23.04.2015,12:56:39,$CRX:FPUcodex=0
23.04.2015,12:56:39,$CRX:GS =13
23.04.2015,12:56:39,$CRX:GA =624
23.04.2015,12:56:39,$CRX:Delay=0msec
23.04.2015,12:56:39,$CRX:Frequency=45.0MHz
23.04.2015,12:56:39,$HST:Receiver connected
23.04.2015,12:56:39,$CRX:Sweeplength=200
23.04.2015,12:56:39,$CRX:low_band_max=171MHz
23.04.2015,12:56:39,$CRX:mid_band_max=450MHz
23.04.2015,12:56:39,$CRX:high_band_max=863MHz
23.04.2015,12:56:39,$CRX:Idle=0x
23.04.2015,12:56:41,$HST:Auto stop due to data loss.
23.04.2015,12:56:42,$HST:Measurement stop
23.04.2015,12:56:42,$HST:Measurement wait...
23.04.2015,12:56:43,$HST:Measurement halted
23.04.2015,12:56:43,$HST:Measurement idle
23.04.2015,12:56:43,$CRX:Stopped
23.04.2015,12:56:43,$HST:Measurement enable
23.04.2015,12:56:43,$CRX:AGC gain = 1.57V
23.04.2015,12:56:43,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:56:43,$CRX:Analog Input = 9.24
23.04.2015,12:56:44,$HST:Check RS232-connection!
23.04.2015,12:56:47,$HST:Attempting Auto-Start
23.04.2015,12:56:48,$HST:Param. RCU due to START
23.04.2015,12:56:48,$HST:Actual focuscode 02
23.04.2015,12:56:48,$HST:Enable data transfer
23.04.2015,12:56:48,$HST:Receiver calibration
23.04.2015,12:56:48,$CRX:Started
23.04.2015,12:56:48,$HST:Start new FITS-file
23.04.2015,12:56:48,$HST:Continous measurement
23.04.2015,12:56:50,$CRX:e-Callisto ETH Zurich
23.04.2015,12:56:50,$HST:Watchdog triggered -> Reset
23.04.2015,12:56:50,$CRX:V1.5, 2006-11-04
23.04.2015,12:56:50,$CRX:ChargePump=On
23.04.2015,12:56:50,$HST:CD1316LV/IV detected
23.04.2015,12:56:50,$CRX:Debug=Off
23.04.2015,12:56:50,$CRX:Trigger=No
23.04.2015,12:56:50,$CRX:FPUcodex=0
23.04.2015,12:56:50,$CRX:GS =13
23.04.2015,12:56:50,$CRX:GA =253
23.04.2015,12:56:50,$CRX:Delay=0msec
23.04.2015,12:56:50,$CRX:Frequency=0.0MHz
23.04.2015,12:56:50,$HST:Receiver connected
23.04.2015,12:56:50,$CRX:Sweeplength=0
23.04.2015,12:56:50,$CRX:low_band_max=171MHz
23.04.2015,12:56:50,$CRX:mid_band_max=450MHz
23.04.2015,12:56:50,$CRX:high_band_max=863MHz
23.04.2015,12:56:50,$CRX:Idle=0x
23.04.2015,12:56:50,$CRX:ChargePump=On
23.04.2015,12:56:50,$HST:CD1316LV/IV detected
23.04.2015,12:56:50,$CRX:Debug=Off
23.04.2015,12:56:50,$CRX:Trigger=Extern
23.04.2015,12:56:50,$CRX:FPUcodex=0
23.04.2015,12:56:50,$CRX:GS =13
23.04.2015,12:56:50,$CRX:GA =624
23.04.2015,12:56:50,$CRX:Delay=0msec
23.04.2015,12:56:50,$CRX:Frequency=45.0MHz
23.04.2015,12:56:50,$HST:Receiver connected
23.04.2015,12:56:50,$CRX:Sweeplength=200
23.04.2015,12:56:50,$CRX:low_band_max=171MHz
23.04.2015,12:56:50,$CRX:mid_band_max=450MHz
23.04.2015,12:56:50,$CRX:high_band_max=863MHz
23.04.2015,12:56:50,$CRX:Idle=0x
23.04.2015,12:56:53,$HST:Auto stop due to data loss.
23.04.2015,12:56:53,$HST:Measurement stop
23.04.2015,12:56:53,$HST:Measurement wait...
23.04.2015,12:56:54,$HST:Measurement halted
23.04.2015,12:56:54,$HST:Measurement idle
23.04.2015,12:56:54,$CRX:Stopped
23.04.2015,12:56:54,$HST:Measurement enable
23.04.2015,12:56:54,$CRX:AGC gain = 1.57V
23.04.2015,12:56:54,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:56:54,$CRX:Analog Input = 9.24
23.04.2015,12:56:56,$HST:Check RS232-connection!
23.04.2015,12:56:59,$HST:Attempting Auto-Start
23.04.2015,12:56:59,$HST:Param. RCU due to START
23.04.2015,12:56:59,$HST:Actual focuscode 02
23.04.2015,12:56:59,$HST:Enable data transfer
23.04.2015,12:56:59,$HST:Receiver calibration
23.04.2015,12:56:59,$CRX:Started
23.04.2015,12:56:59,$HST:Start new FITS-file
23.04.2015,12:57:00,$HST:Continous measurement
23.04.2015,12:57:01,$CRX:e-Callisto ETH Zurich
23.04.2015,12:57:01,$HST:Watchdog triggered -> Reset
23.04.2015,12:57:01,$CRX:V1.5, 2006-11-04
23.04.2015,12:57:01,$CRX:ChargePump=On
23.04.2015,12:57:01,$HST:CD1316LV/IV detected
23.04.2015,12:57:01,$CRX:Debug=Off
23.04.2015,12:57:01,$CRX:Trigger=No
23.04.2015,12:57:01,$CRX:FPUcodex=0
23.04.2015,12:57:01,$CRX:GS =13
23.04.2015,12:57:01,$CRX:GA =253
23.04.2015,12:57:01,$CRX:Delay=0msec
23.04.2015,12:57:01,$CRX:Frequency=0.0MHz
23.04.2015,12:57:01,$HST:Receiver connected
23.04.2015,12:57:01,$CRX:Sweeplength=0
23.04.2015,12:57:01,$CRX:low_band_max=171MHz
23.04.2015,12:57:01,$CRX:mid_band_max=450MHz
23.04.2015,12:57:01,$CRX:high_band_max=863MHz
23.04.2015,12:57:01,$CRX:Idle=0x
23.04.2015,12:57:01,$CRX:ChargePump=On
23.04.2015,12:57:01,$HST:CD1316LV/IV detected
23.04.2015,12:57:01,$CRX:Debug=Off
23.04.2015,12:57:01,$CRX:Trigger=Extern
23.04.2015,12:57:01,$CRX:FPUcodex=0
23.04.2015,12:57:01,$CRX:GS =13
23.04.2015,12:57:01,$CRX:GA =624
23.04.2015,12:57:01,$CRX:Delay=0msec
23.04.2015,12:57:01,$CRX:Frequency=45.0MHz
23.04.2015,12:57:01,$HST:Receiver connected
23.04.2015,12:57:01,$CRX:Sweeplength=200
23.04.2015,12:57:01,$CRX:low_band_max=171MHz
23.04.2015,12:57:01,$CRX:mid_band_max=450MHz
23.04.2015,12:57:01,$CRX:high_band_max=863MHz
23.04.2015,12:57:01,$CRX:Idle=0x
23.04.2015,12:57:04,$HST:Auto stop due to data loss.
23.04.2015,12:57:04,$HST:Measurement stop
23.04.2015,12:57:05,$HST:Measurement wait...
23.04.2015,12:57:05,$HST:Measurement halted
23.04.2015,12:57:06,$HST:Measurement idle
23.04.2015,12:57:06,$CRX:Stopped
23.04.2015,12:57:06,$HST:Measurement enable
23.04.2015,12:57:06,$CRX:AGC gain = 1.57V
23.04.2015,12:57:06,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:57:06,$CRX:Analog Input = 9.24
23.04.2015,12:57:07,$HST:Check RS232-connection!
23.04.2015,12:57:10,$HST:Attempting Auto-Start
23.04.2015,12:57:10,$HST:Param. RCU due to START
23.04.2015,12:57:10,$HST:Actual focuscode 02
23.04.2015,12:57:11,$HST:Enable data transfer
23.04.2015,12:57:11,$HST:Receiver calibration
23.04.2015,12:57:11,$CRX:Started
23.04.2015,12:57:11,$HST:Start new FITS-file
23.04.2015,12:57:11,$HST:Continous measurement
23.04.2015,12:57:13,$CRX:e-Callisto ETH Zurich
23.04.2015,12:57:13,$HST:Watchdog triggered -> Reset
23.04.2015,12:57:13,$CRX:V1.5, 2006-11-04
23.04.2015,12:57:13,$CRX:ChargePump=On
23.04.2015,12:57:13,$HST:CD1316LV/IV detected
23.04.2015,12:57:13,$CRX:Debug=Off
23.04.2015,12:57:13,$CRX:Trigger=No
23.04.2015,12:57:13,$CRX:FPUcodex=0
23.04.2015,12:57:13,$CRX:GS =13
23.04.2015,12:57:13,$CRX:GA =253
23.04.2015,12:57:13,$CRX:Delay=0msec
23.04.2015,12:57:13,$CRX:Frequency=0.0MHz
23.04.2015,12:57:13,$HST:Receiver connected
23.04.2015,12:57:13,$CRX:Sweeplength=0
23.04.2015,12:57:13,$CRX:low_band_max=171MHz
23.04.2015,12:57:13,$CRX:mid_band_max=450MHz
23.04.2015,12:57:13,$CRX:high_band_max=863MHz
23.04.2015,12:57:13,$CRX:Idle=0x
23.04.2015,12:57:13,$CRX:ChargePump=On
23.04.2015,12:57:13,$HST:CD1316LV/IV detected
23.04.2015,12:57:13,$CRX:Debug=Off
23.04.2015,12:57:13,$CRX:Trigger=Extern
23.04.2015,12:57:13,$CRX:FPUcodex=0
23.04.2015,12:57:13,$CRX:GS =13
23.04.2015,12:57:13,$CRX:GA =624
23.04.2015,12:57:13,$CRX:Delay=0msec
23.04.2015,12:57:13,$CRX:Frequency=45.0MHz
23.04.2015,12:57:13,$HST:Receiver connected
23.04.2015,12:57:13,$CRX:Sweeplength=200
23.04.2015,12:57:13,$CRX:low_band_max=171MHz
23.04.2015,12:57:13,$CRX:mid_band_max=450MHz
23.04.2015,12:57:13,$CRX:high_band_max=863MHz
23.04.2015,12:57:13,$CRX:Idle=0x
23.04.2015,12:57:16,$HST:Auto stop due to data loss.
23.04.2015,12:57:16,$HST:Measurement stop
23.04.2015,12:57:16,$HST:Measurement wait...
23.04.2015,12:57:17,$HST:Measurement halted
23.04.2015,12:57:17,$HST:Measurement idle
23.04.2015,12:57:17,$CRX:Stopped
23.04.2015,12:57:17,$HST:Measurement enable
23.04.2015,12:57:17,$CRX:AGC gain = 1.56V
23.04.2015,12:57:17,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:57:17,$CRX:Analog Input = 9.24
23.04.2015,12:57:19,$HST:Check RS232-connection!
23.04.2015,12:57:22,$HST:Attempting Auto-Start
23.04.2015,12:57:22,$HST:Param. RCU due to START
23.04.2015,12:57:22,$HST:Actual focuscode 02
23.04.2015,12:57:22,$HST:Enable data transfer
23.04.2015,12:57:22,$HST:Receiver calibration
23.04.2015,12:57:22,$CRX:Started
23.04.2015,12:57:22,$HST:Start new FITS-file
23.04.2015,12:57:22,$HST:Continous measurement
23.04.2015,12:57:24,$CRX:e-Callisto ETH Zurich
23.04.2015,12:57:24,$HST:Watchdog triggered -> Reset
23.04.2015,12:57:24,$CRX:V1.5, 2006-11-04
23.04.2015,12:57:24,$CRX:ChargePump=On
23.04.2015,12:57:24,$HST:CD1316LV/IV detected
23.04.2015,12:57:24,$CRX:Debug=Off
23.04.2015,12:57:24,$CRX:Trigger=No
23.04.2015,12:57:24,$CRX:FPUcodex=0
23.04.2015,12:57:24,$CRX:GS =13
23.04.2015,12:57:24,$CRX:GA =253
23.04.2015,12:57:24,$CRX:Delay=0msec
23.04.2015,12:57:24,$CRX:Frequency=0.0MHz
23.04.2015,12:57:24,$HST:Receiver connected
23.04.2015,12:57:24,$CRX:Sweeplength=0
23.04.2015,12:57:24,$CRX:low_band_max=171MHz
23.04.2015,12:57:24,$CRX:mid_band_max=450MHz
23.04.2015,12:57:24,$CRX:high_band_max=863MHz
23.04.2015,12:57:24,$CRX:Idle=0x
23.04.2015,12:57:24,$CRX:ChargePump=On
23.04.2015,12:57:24,$HST:CD1316LV/IV detected
23.04.2015,12:57:24,$CRX:Debug=Off
23.04.2015,12:57:24,$CRX:Trigger=Extern
23.04.2015,12:57:24,$CRX:FPUcodex=0
23.04.2015,12:57:24,$CRX:GS =13
23.04.2015,12:57:24,$CRX:GA =624
23.04.2015,12:57:24,$CRX:Delay=0msec
23.04.2015,12:57:24,$CRX:Frequency=45.0MHz
23.04.2015,12:57:24,$HST:Receiver connected
23.04.2015,12:57:24,$CRX:Sweeplength=200
23.04.2015,12:57:24,$CRX:low_band_max=171MHz
23.04.2015,12:57:24,$CRX:mid_band_max=450MHz
23.04.2015,12:57:24,$CRX:high_band_max=863MHz
23.04.2015,12:57:24,$CRX:Idle=0x
23.04.2015,12:57:27,$HST:Auto stop due to data loss.
23.04.2015,12:57:27,$HST:Measurement stop
23.04.2015,12:57:27,$HST:Measurement wait...
23.04.2015,12:57:28,$HST:Measurement halted
23.04.2015,12:57:28,$HST:Measurement idle
23.04.2015,12:57:28,$CRX:Stopped
23.04.2015,12:57:29,$HST:Measurement enable
23.04.2015,12:57:29,$CRX:AGC gain = 1.56V
23.04.2015,12:57:29,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:57:29,$CRX:Analog Input = 9.24
23.04.2015,12:57:30,$HST:Check RS232-connection!
23.04.2015,12:57:33,$HST:Attempting Auto-Start
23.04.2015,12:57:33,$HST:Param. RCU due to START
23.04.2015,12:57:33,$HST:Actual focuscode 02
23.04.2015,12:57:33,$HST:Enable data transfer
23.04.2015,12:57:33,$HST:Receiver calibration
23.04.2015,12:57:33,$CRX:Started
23.04.2015,12:57:34,$HST:Start new FITS-file
23.04.2015,12:57:34,$HST:Continous measurement
23.04.2015,12:57:36,$CRX:e-Callisto ETH Zurich
23.04.2015,12:57:36,$HST:Watchdog triggered -> Reset
23.04.2015,12:57:36,$CRX:V1.5, 2006-11-04
23.04.2015,12:57:36,$CRX:ChargePump=On
23.04.2015,12:57:36,$HST:CD1316LV/IV detected
23.04.2015,12:57:36,$CRX:Debug=Off
23.04.2015,12:57:36,$CRX:Trigger=No
23.04.2015,12:57:36,$CRX:FPUcodex=0
23.04.2015,12:57:36,$CRX:GS =13
23.04.2015,12:57:36,$CRX:GA =253
23.04.2015,12:57:36,$CRX:Delay=0msec
23.04.2015,12:57:36,$CRX:Frequency=0.0MHz
23.04.2015,12:57:36,$HST:Receiver connected
23.04.2015,12:57:36,$CRX:Sweeplength=0
23.04.2015,12:57:36,$CRX:low_band_max=171MHz
23.04.2015,12:57:36,$CRX:mid_band_max=450MHz
23.04.2015,12:57:36,$CRX:high_band_max=863MHz
23.04.2015,12:57:36,$CRX:Idle=0x
23.04.2015,12:57:36,$CRX:ChargePump=On
23.04.2015,12:57:36,$HST:CD1316LV/IV detected
23.04.2015,12:57:36,$CRX:Debug=Off
23.04.2015,12:57:36,$CRX:Trigger=Extern
23.04.2015,12:57:36,$CRX:FPUcodex=0
23.04.2015,12:57:36,$CRX:GS =13
23.04.2015,12:57:36,$CRX:GA =624
23.04.2015,12:57:36,$CRX:Delay=0msec
23.04.2015,12:57:36,$CRX:Frequency=45.0MHz
23.04.2015,12:57:36,$HST:Receiver connected
23.04.2015,12:57:36,$CRX:Sweeplength=200
23.04.2015,12:57:36,$CRX:low_band_max=171MHz
23.04.2015,12:57:36,$CRX:mid_band_max=450MHz
23.04.2015,12:57:36,$CRX:high_band_max=863MHz
23.04.2015,12:57:36,$CRX:Idle=0x
23.04.2015,12:57:39,$HST:Auto stop due to data loss.
23.04.2015,12:57:39,$HST:Measurement stop
23.04.2015,12:57:39,$HST:Measurement wait...
23.04.2015,12:57:40,$HST:Measurement halted
23.04.2015,12:57:40,$HST:Measurement idle
23.04.2015,12:57:40,$CRX:Stopped
23.04.2015,12:57:40,$HST:Measurement enable
23.04.2015,12:57:40,$CRX:AGC gain = 1.56V
23.04.2015,12:57:40,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:57:40,$CRX:Analog Input = 9.24
23.04.2015,12:57:42,$HST:Check RS232-connection!
23.04.2015,12:57:45,$HST:Attempting Auto-Start
23.04.2015,12:57:45,$HST:Param. RCU due to START
23.04.2015,12:57:45,$HST:Actual focuscode 02
23.04.2015,12:57:45,$HST:Enable data transfer
23.04.2015,12:57:45,$HST:Receiver calibration
23.04.2015,12:57:45,$CRX:Started
23.04.2015,12:57:45,$HST:Start new FITS-file
23.04.2015,12:57:45,$HST:Continous measurement
23.04.2015,12:57:47,$CRX:e-Callisto ETH Zurich
23.04.2015,12:57:47,$HST:Watchdog triggered -> Reset
23.04.2015,12:57:47,$CRX:V1.5, 2006-11-04
23.04.2015,12:57:47,$CRX:ChargePump=On
23.04.2015,12:57:47,$HST:CD1316LV/IV detected
23.04.2015,12:57:47,$CRX:Debug=Off
23.04.2015,12:57:47,$CRX:Trigger=No
23.04.2015,12:57:47,$CRX:FPUcodex=0
23.04.2015,12:57:47,$CRX:GS =13
23.04.2015,12:57:47,$CRX:GA =253
23.04.2015,12:57:47,$CRX:Delay=0msec
23.04.2015,12:57:47,$CRX:Frequency=0.0MHz
23.04.2015,12:57:47,$HST:Receiver connected
23.04.2015,12:57:47,$CRX:Sweeplength=0
23.04.2015,12:57:47,$CRX:low_band_max=171MHz
23.04.2015,12:57:47,$CRX:mid_band_max=450MHz
23.04.2015,12:57:47,$CRX:high_band_max=863MHz
23.04.2015,12:57:47,$CRX:Idle=0x
23.04.2015,12:57:47,$CRX:ChargePump=On
23.04.2015,12:57:47,$HST:CD1316LV/IV detected
23.04.2015,12:57:47,$CRX:Debug=Off
23.04.2015,12:57:47,$CRX:Trigger=Extern
23.04.2015,12:57:47,$CRX:FPUcodex=0
23.04.2015,12:57:47,$CRX:GS =13
23.04.2015,12:57:47,$CRX:GA =624
23.04.2015,12:57:47,$CRX:Delay=0msec
23.04.2015,12:57:47,$CRX:Frequency=45.0MHz
23.04.2015,12:57:47,$HST:Receiver connected
23.04.2015,12:57:47,$CRX:Sweeplength=200
23.04.2015,12:57:47,$CRX:low_band_max=171MHz
23.04.2015,12:57:47,$CRX:mid_band_max=450MHz
23.04.2015,12:57:47,$CRX:high_band_max=863MHz
23.04.2015,12:57:47,$CRX:Idle=0x
23.04.2015,12:57:50,$HST:Auto stop due to data loss.
23.04.2015,12:57:50,$HST:Measurement stop
23.04.2015,12:57:50,$HST:Measurement wait...
23.04.2015,12:57:51,$HST:Measurement halted
23.04.2015,12:57:51,$HST:Measurement idle
23.04.2015,12:57:51,$CRX:Stopped
23.04.2015,12:57:51,$HST:Measurement enable
23.04.2015,12:57:51,$CRX:AGC gain = 1.56V
23.04.2015,12:57:51,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:57:51,$CRX:Analog Input = 9.24
23.04.2015,12:57:53,$HST:Check RS232-connection!
23.04.2015,12:57:56,$HST:Attempting Auto-Start
23.04.2015,12:57:56,$HST:Param. RCU due to START
23.04.2015,12:57:56,$HST:Actual focuscode 02
23.04.2015,12:57:56,$HST:Enable data transfer
23.04.2015,12:57:56,$HST:Receiver calibration
23.04.2015,12:57:56,$CRX:Started
23.04.2015,12:57:57,$HST:Start new FITS-file
23.04.2015,12:57:57,$HST:Continous measurement
23.04.2015,12:57:58,$CRX:e-Callisto ETH Zurich
23.04.2015,12:57:58,$HST:Watchdog triggered -> Reset
23.04.2015,12:57:58,$CRX:V1.5, 2006-11-04
23.04.2015,12:57:59,$CRX:ChargePump=On
23.04.2015,12:57:59,$HST:CD1316LV/IV detected
23.04.2015,12:57:59,$CRX:Debug=Off
23.04.2015,12:57:59,$CRX:Trigger=No
23.04.2015,12:57:59,$CRX:FPUcodex=0
23.04.2015,12:57:59,$CRX:GS =13
23.04.2015,12:57:59,$CRX:GA =253
23.04.2015,12:57:59,$CRX:Delay=0msec
23.04.2015,12:57:59,$CRX:Frequency=0.0MHz
23.04.2015,12:57:59,$HST:Receiver connected
23.04.2015,12:57:59,$CRX:Sweeplength=0
23.04.2015,12:57:59,$CRX:low_band_max=171MHz
23.04.2015,12:57:59,$CRX:mid_band_max=450MHz
23.04.2015,12:57:59,$CRX:high_band_max=863MHz
23.04.2015,12:57:59,$CRX:Idle=0x
23.04.2015,12:57:59,$CRX:ChargePump=On
23.04.2015,12:57:59,$HST:CD1316LV/IV detected
23.04.2015,12:57:59,$CRX:Debug=Off
23.04.2015,12:57:59,$CRX:Trigger=Extern
23.04.2015,12:57:59,$CRX:FPUcodex=0
23.04.2015,12:57:59,$CRX:GS =13
23.04.2015,12:57:59,$CRX:GA =624
23.04.2015,12:57:59,$CRX:Delay=0msec
23.04.2015,12:57:59,$CRX:Frequency=45.0MHz
23.04.2015,12:57:59,$HST:Receiver connected
23.04.2015,12:57:59,$CRX:Sweeplength=200
23.04.2015,12:57:59,$CRX:low_band_max=171MHz
23.04.2015,12:57:59,$CRX:mid_band_max=450MHz
23.04.2015,12:57:59,$CRX:high_band_max=863MHz
23.04.2015,12:57:59,$CRX:Idle=0x
23.04.2015,12:58:01,$HST:Auto stop due to data loss.
23.04.2015,12:58:02,$HST:Measurement stop
23.04.2015,12:58:02,$HST:Measurement wait...
23.04.2015,12:58:03,$HST:Measurement halted
23.04.2015,12:58:03,$HST:Measurement idle
23.04.2015,12:58:03,$CRX:Stopped
23.04.2015,12:58:03,$HST:Measurement enable
23.04.2015,12:58:03,$CRX:AGC gain = 1.56V
23.04.2015,12:58:03,$CRX:Emitter BF199 = 0.14V
23.04.2015,12:58:03,$CRX:Analog Input = 9.24
23.04.2015,12:58:04,$HST:Check RS232-connection!
23.04.2015,12:58:07,$HST:Attempting Auto-Start
23.04.2015,12:58:08,$HST:Param. RCU due to START
23.04.2015,12:58:08,$HST:Actual focuscode 02
23.04.2015,12:58:08,$HST:Enable data transfer
23.04.2015,12:58:08,$HST:Receiver calibration
23.04.2015,12:58:08,$CRX:Started
23.04.2015,12:58:08,$HST:Start new FITS-file
23.04.2015,12:58:08,$HST:Continous measurement
23.04.2015,13:10:02,$HST:Measurement stop
23.04.2015,13:10:02,$HST:FITS #17 200rows x 2855cols
23.04.2015,13:10:02,$HST:Measurement wait...
23.04.2015,13:10:02,$HST:EOT (&) detected
23.04.2015,13:10:02,$HST:Measurement halted
23.04.2015,13:10:02,$HST:Measurement idle
23.04.2015,13:10:02,$CRX:Stopped
23.04.2015,13:10:02,$HST:Measurement enable
23.04.2015,13:10:02,$CRX:AGC gain = 1.57V
23.04.2015,13:10:02,$CRX:Emitter BF199 = 0.14V
23.04.2015,13:10:02,$CRX:Analog Input = 9.24
23.04.2015,13:10:03,$HST:Start overview...
23.04.2015,13:10:03,$HST:Wait ~45sec please!
23.04.2015,13:10:45,$HST:End spectral overview...
23.04.2015,13:10:45,$HST:Data in log-directory
23.04.2015,13:11:08,$HST:Param. RCU due to START
23.04.2015,13:11:08,$HST:Actual focuscode 02
23.04.2015,13:11:08,$HST:Enable data transfer
23.04.2015,13:11:08,$HST:Receiver calibration
23.04.2015,13:11:08,$CRX:Started
23.04.2015,13:11:08,$HST:Start new FITS-file
23.04.2015,13:11:09,$HST:Continous measurement
23.04.2015,13:11:52,$HST:Measurement stop
23.04.2015,13:11:52,$HST:FITS #18 200rows x 175cols
23.04.2015,13:11:52,$HST:EOT (&) detected
23.04.2015,13:11:52,$HST:Measurement wait...
23.04.2015,13:11:52,$HST:Measurement halted
23.04.2015,13:11:52,$HST:Measurement idle
23.04.2015,13:11:52,$CRX:Stopped
23.04.2015,13:11:53,$HST:Measurement enable
23.04.2015,13:11:53,$CRX:AGC gain = 1.57V
23.04.2015,13:11:53,$CRX:Emitter BF199 = 0.14V
23.04.2015,13:11:53,$CRX:Analog Input = 9.24
23.04.2015,13:11:54,$HST:Start overview...
23.04.2015,13:11:54,$HST:Wait ~45sec please!
23.04.2015,13:12:36,$HST:End spectral overview...
23.04.2015,13:12:36,$HST:Data in log-directory
23.04.2015,13:16:19,$HST:Param. RCU due to START
23.04.2015,13:16:19,$HST:Actual focuscode 02
23.04.2015,13:16:20,$HST:Enable data transfer
23.04.2015,13:16:20,$HST:Receiver calibration
23.04.2015,13:16:20,$CRX:Started
23.04.2015,13:16:20,$HST:Start new FITS-file
23.04.2015,13:16:20,$HST:Continous measurement
23.04.2015,13:16:31,$HST:scheduler.cfg watched
23.04.2015,13:29:58,$HST:Measurement stop
23.04.2015,13:29:58,$HST:FITS #19 200rows x 3272cols
23.04.2015,13:29:58,$HST:Measurement wait...
23.04.2015,13:29:58,$HST:EOT (&) detected
23.04.2015,13:29:58,$HST:Measurement halted
23.04.2015,13:29:58,$HST:Measurement stop
23.04.2015,13:29:58,$CRX:Stopped
23.04.2015,13:29:59,$HST:Measurement wait...
23.04.2015,13:29:59,$HST:Measurement halted
23.04.2015,13:30:00,$HST:Measurement idle
23.04.2015,13:30:00,$CRX:Stopped
23.04.2015,13:30:00,$HST:Measurement enable
23.04.2015,13:30:00,$CRX:AGC gain = 1.56V
23.04.2015,13:30:00,$CRX:Emitter BF199 = 0.14V
23.04.2015,13:30:00,$CRX:Analog Input = 9.24
23.04.2015,13:30:00,$HST:Autostart via scheduler
23.04.2015,13:30:00,$HST:Param. RCU due to START
23.04.2015,13:30:00,$HST:Actual focuscode 02
23.04.2015,13:30:00,$HST:Enable data transfer
23.04.2015,13:30:00,$HST:Receiver calibration
23.04.2015,13:30:00,$CRX:Started
23.04.2015,13:30:00,$HST:Start new FITS-file
23.04.2015,13:30:00,$HST:Continous measurement
23.04.2015,13:45:00,$HST:FITS #20 200rows x 3600cols
23.04.2015,14:00:00,$HST:FITS #21 200rows x 3600cols
23.04.2015,14:15:00,$HST:FITS #22 200rows x 3600cols
23.04.2015,14:30:00,$HST:FITS #23 200rows x 3600cols
23.04.2015,14:45:00,$HST:FITS #24 200rows x 3600cols
23.04.2015,15:00:00,$HST:FITS #25 200rows x 3600cols
23.04.2015,15:15:00,$HST:FITS #26 200rows x 3600cols
23.04.2015,15:30:00,$HST:FITS #27 200rows x 3600cols
23.04.2015,15:45:00,$HST:FITS #28 200rows x 3600cols
23.04.2015,16:00:00,$HST:FITS #29 200rows x 3600cols
23.04.2015,16:15:00,$HST:FITS #30 200rows x 3600cols
23.04.2015,16:30:00,$HST:FITS #31 200rows x 3600cols
23.04.2015,16:45:00,$HST:FITS #32 200rows x 3600cols
23.04.2015,17:00:00,$HST:FITS #33 200rows x 3600cols
23.04.2015,17:15:00,$HST:FITS #34 200rows x 3600cols
23.04.2015,17:30:00,$HST:FITS #35 200rows x 3600cols
23.04.2015,17:45:00,$HST:FITS #36 200rows x 3600cols
23.04.2015,18:00:00,$HST:FITS #37 200rows x 3600cols
23.04.2015,18:14:58,$HST:Measurement stop
23.04.2015,18:14:58,$HST:FITS #38 200rows x 3591cols
23.04.2015,18:14:58,$HST:Measurement wait...
23.04.2015,18:14:58,$HST:EOT (&) detected
23.04.2015,18:14:58,$HST:Measurement halted
23.04.2015,18:14:58,$HST:Measurement stop
23.04.2015,18:14:58,$CRX:Stopped
23.04.2015,18:14:59,$HST:Measurement wait...
23.04.2015,18:14:59,$HST:Measurement halted
23.04.2015,18:14:59,$HST:Measurement idle
23.04.2015,18:14:59,$CRX:Stopped
23.04.2015,18:15:00,$HST:Measurement enable
23.04.2015,18:15:00,$CRX:AGC gain = 1.57V
23.04.2015,18:15:00,$CRX:Emitter BF199 = 0.14V
23.04.2015,18:15:00,$CRX:Analog Input = 9.24
23.04.2015,18:15:01,$HST:No more entries in scheduler.
24.04.2015,00:00:00,$HST:Midnight -> memo cleared
24.04.2015,00:00:00,$HST:EOF(logfile)