19.02.2015,15:52:14,$HST:Application just created
19.02.2015,15:52:14,$HST:SW-version 1.17, e-Callisto
19.02.2015,15:52:14,$HST:Configurationfile read
19.02.2015,15:52:14,$HST:Switched to automatic
19.02.2015,15:52:14,$HST:ATmega16 pre-configured
19.02.2015,15:52:14,$HST:Frequencyfile frq00255.cfg
19.02.2015,15:52:14,$HST:Callisto ready now...
19.02.2015,15:52:14,$HST:Measurement idle
19.02.2015,15:52:15,$HST:File scheduler.cfg read
19.02.2015,15:52:15,$HST:Measurement enable
19.02.2015,15:52:15,$CRX:AGC gain = 1.59V
19.02.2015,15:52:15,$CRX:Emitter BF199 = 0.13V
19.02.2015,15:52:15,$CRX:Analog Input = 9.24
19.02.2015,15:52:20,$HST:File frq00255.cfg read
19.02.2015,15:52:20,$HST:No calibration file found
19.02.2015,15:52:20,$HST:Plot buffer erased...
19.02.2015,15:52:20,$HST:Parametrisation RCU
19.02.2015,15:52:20,$CRX:ChargePump=On
19.02.2015,15:52:20,$HST:CD1316LV/IV detected
19.02.2015,15:52:20,$CRX:Debug=Off
19.02.2015,15:52:20,$CRX:Trigger=Intern
19.02.2015,15:52:20,$CRX:FPUcodex=1
19.02.2015,15:52:20,$CRX:GS =3396
19.02.2015,15:52:20,$CRX:GA =253
19.02.2015,15:52:20,$CRX:Delay=2msec
19.02.2015,15:52:20,$CRX:Frequency=45.0MHz
19.02.2015,15:52:20,$HST:Receiver connected
19.02.2015,15:52:20,$CRX:Sweeplength=200
19.02.2015,15:52:20,$CRX:low_band_max=171MHz
19.02.2015,15:52:20,$CRX:mid_band_max=450MHz
19.02.2015,15:52:20,$CRX:high_band_max=863MHz
19.02.2015,15:52:20,$CRX:Idle=0x
19.02.2015,15:52:20,$CRX:ChargePump=On
19.02.2015,15:52:20,$HST:CD1316LV/IV detected
19.02.2015,15:52:20,$CRX:Debug=Off
19.02.2015,15:52:20,$CRX:Trigger=Intern
19.02.2015,15:52:20,$CRX:FPUcodex=1
19.02.2015,15:52:20,$CRX:GS =3396
19.02.2015,15:52:20,$CRX:GA =253
19.02.2015,15:52:20,$CRX:Delay=2msec
19.02.2015,15:52:20,$CRX:Frequency=45.0MHz
19.02.2015,15:52:20,$HST:Receiver connected
19.02.2015,15:52:20,$CRX:Sweeplength=200
19.02.2015,15:52:20,$CRX:low_band_max=171MHz
19.02.2015,15:52:20,$CRX:mid_band_max=450MHz
19.02.2015,15:52:20,$CRX:high_band_max=863MHz
19.02.2015,15:52:20,$CRX:Idle=0x
19.02.2015,15:52:26,$HST:File FRQ00255.CFG read
19.02.2015,15:52:26,$HST:No calibration file found
19.02.2015,15:52:26,$HST:Plot buffer erased...
19.02.2015,15:52:26,$HST:Parametrisation RCU
19.02.2015,15:52:28,$HST:Switched to manual
19.02.2015,15:52:30,$HST:Param. RCU due to START
19.02.2015,15:52:30,$HST:Actual focuscode 01
19.02.2015,15:52:30,$HST:Enable data transfer
19.02.2015,15:52:30,$HST:Receiver calibration
19.02.2015,15:52:30,$HST:Start new FITS-file
19.02.2015,15:52:30,$HST:Continous measurement
19.02.2015,15:52:31,$HST:Yt plot selected
19.02.2015,15:52:31,$HST:XY plot selected
19.02.2015,15:52:32,$HST:XYZ plot selected
19.02.2015,15:52:46,$HST:Measurement stop
19.02.2015,15:52:46,$HST:Measurement wait...
19.02.2015,15:52:47,$HST:Measurement halted
19.02.2015,15:52:47,$HST:Measurement idle
19.02.2015,15:52:47,$HST:Measurement enable
19.02.2015,15:52:50,$HST:Param. RCU due to START
19.02.2015,15:52:50,$HST:Actual focuscode 01
19.02.2015,15:52:50,$HST:Enable data transfer
19.02.2015,15:52:50,$HST:Receiver calibration
19.02.2015,15:52:50,$HST:Start new FITS-file
19.02.2015,15:52:50,$HST:Continous measurement
19.02.2015,15:53:01,$HST:All threads terminated
19.02.2015,15:53:01,$HST:This application closed