19.11.2014,13:42:32,$HST:Application just created
19.11.2014,13:42:32,$HST:SW-version 1.16, e-Callisto
19.11.2014,13:42:32,$HST:Configurationfile read
19.11.2014,13:42:32,$HST:Switched to automatic
19.11.2014,13:42:32,$HST:ATmega16 pre-configured
19.11.2014,13:42:32,$HST:Frequencyfile frq00255.cfg
19.11.2014,13:42:32,$HST:Callisto ready now...
19.11.2014,13:42:33,$HST:Measurement idle
19.11.2014,13:42:33,$HST:File scheduler.cfg read
19.11.2014,13:42:33,$HST:Measurement enable
19.11.2014,13:42:33,$CRX:AGC gain = 1.79V
19.11.2014,13:42:33,$CRX:Emitter BF199 = 0.12V
19.11.2014,13:42:33,$CRX:Analog Input = 9.24
19.11.2014,13:42:38,$HST:XY plot selected
19.11.2014,13:42:39,$HST:File frq00255.cfg read
19.11.2014,13:42:39,$HST:No calibration file found
19.11.2014,13:42:39,$HST:Plot buffer erased...
19.11.2014,13:42:39,$HST:Parametrisation RCU
19.11.2014,13:42:39,$CRX:ChargePump=On
19.11.2014,13:42:39,$HST:CD1316LV/IV detected
19.11.2014,13:42:39,$CRX:Debug=Off
19.11.2014,13:42:39,$CRX:Trigger=Soft
19.11.2014,13:42:39,$CRX:FPUcodex=58
19.11.2014,13:42:39,$CRX:GS =61750
19.11.2014,13:42:39,$CRX:GA =253
19.11.2014,13:42:39,$CRX:Delay=2msec
19.11.2014,13:42:39,$CRX:Frequency=870.0MHz
19.11.2014,13:42:39,$HST:Receiver connected
19.11.2014,13:42:39,$CRX:Sweeplength=200
19.11.2014,13:42:39,$CRX:low_band_max=171MHz
19.11.2014,13:42:39,$CRX:mid_band_max=450MHz
19.11.2014,13:42:39,$CRX:high_band_max=863MHz
19.11.2014,13:42:39,$CRX:Idle=0x
19.11.2014,13:42:39,$CRX:ChargePump=On
19.11.2014,13:42:39,$HST:CD1316LV/IV detected
19.11.2014,13:42:39,$CRX:Debug=Off
19.11.2014,13:42:39,$CRX:Trigger=Extern
19.11.2014,13:42:39,$CRX:FPUcodex=58
19.11.2014,13:42:39,$CRX:GS =61750
19.11.2014,13:42:39,$CRX:GA =624
19.11.2014,13:42:39,$CRX:Delay=2msec
19.11.2014,13:42:39,$CRX:Frequency=45.0MHz
19.11.2014,13:42:39,$HST:Receiver connected
19.11.2014,13:42:39,$CRX:Sweeplength=200
19.11.2014,13:42:39,$CRX:low_band_max=171MHz
19.11.2014,13:42:39,$CRX:mid_band_max=450MHz
19.11.2014,13:42:39,$CRX:high_band_max=863MHz
19.11.2014,13:42:39,$CRX:Idle=0x
19.11.2014,13:42:41,$HST:scheduler.cfg watched
19.11.2014,13:42:53,$HST:Param. RCU due to START
19.11.2014,13:42:53,$HST:Actual focuscode 60
19.11.2014,13:42:53,$HST:Enable data transfer
19.11.2014,13:42:53,$HST:Continuous measurement
19.11.2014,13:42:53,$CRX:Started
19.11.2014,13:42:53,$HST:Start new FITS-file
19.11.2014,13:42:53,$HST:Continous measurement
19.11.2014,13:44:58,$HST:Measurement stop
19.11.2014,13:44:58,$HST:FITS #1 200rows x 498cols
19.11.2014,13:44:58,$HST:Measurement wait...
19.11.2014,13:44:58,$HST:EOT (&) detected
19.11.2014,13:44:58,$HST:Measurement halted
19.11.2014,13:44:58,$HST:Measurement stop
19.11.2014,13:44:58,$CRX:Stopped
19.11.2014,13:44:59,$HST:Measurement wait...
19.11.2014,13:44:59,$HST:Measurement halted
19.11.2014,13:45:00,$HST:Autostart via scheduler
19.11.2014,13:45:00,$HST:Param. RCU due to START
19.11.2014,13:45:00,$HST:Actual focuscode 58
19.11.2014,13:45:00,$CRX:Stopped
19.11.2014,13:45:00,$HST:Enable data transfer
19.11.2014,13:45:00,$HST:Continuous measurement
19.11.2014,13:45:00,$CRX:Started
19.11.2014,13:45:00,$HST:Start new FITS-file
19.11.2014,13:45:00,$HST:Continous measurement
19.11.2014,13:46:30,$HST:XYZ plot selected
19.11.2014,13:46:37,$HST:XYZ plot hidden
19.11.2014,14:00:00,$HST:FITS #2 200rows x 3600cols
19.11.2014,14:15:00,$HST:FITS #3 200rows x 3600cols
19.11.2014,14:30:00,$HST:FITS #4 200rows x 3600cols
19.11.2014,14:45:00,$HST:FITS #5 200rows x 3600cols
19.11.2014,15:00:00,$HST:FITS #6 200rows x 3600cols
19.11.2014,15:15:00,$HST:FITS #7 200rows x 3600cols
19.11.2014,15:29:58,$HST:Measurement stop
19.11.2014,15:29:58,$HST:FITS #8 200rows x 3591cols
19.11.2014,15:29:58,$HST:Measurement wait...
19.11.2014,15:29:58,$HST:EOT (&) detected
19.11.2014,15:29:58,$HST:Measurement halted
19.11.2014,15:29:58,$HST:Measurement stop
19.11.2014,15:29:58,$CRX:Stopped
19.11.2014,15:29:58,$HST:Measurement wait...
19.11.2014,15:29:59,$HST:Measurement halted
19.11.2014,15:29:59,$HST:Measurement idle
19.11.2014,15:29:59,$CRX:Stopped
19.11.2014,15:29:59,$HST:Measurement enable
19.11.2014,15:29:59,$CRX:AGC gain = 1.79V
19.11.2014,15:29:59,$CRX:Emitter BF199 = 0.12V
19.11.2014,15:29:59,$CRX:Analog Input = 9.24
19.11.2014,15:51:54,$HST:No more entries in scheduler.
19.11.2014,16:14:58,$HST:Measurement stop
19.11.2014,16:14:58,$HST:Measurement wait...
19.11.2014,16:14:59,$HST:Measurement halted
19.11.2014,16:14:59,$HST:Measurement idle
19.11.2014,16:14:59,$CRX:Stopped
19.11.2014,16:14:59,$HST:Measurement enable
19.11.2014,16:14:59,$CRX:AGC gain = 1.79V
19.11.2014,16:14:59,$CRX:Emitter BF199 = 0.12V
19.11.2014,16:14:59,$CRX:Analog Input = 9.24
19.11.2014,16:15:00,$HST:Radio monitoring
19.11.2014,16:15:00,$HST:Start overview...
19.11.2014,16:15:00,$HST:Wait ~45sec please!
19.11.2014,16:15:41,$HST:End spectral overview...
19.11.2014,16:15:41,$HST:Data in log-directory
19.11.2014,21:17:46,$HST:scheduler.cfg watched
20.11.2014,00:00:00,$HST:Midnight -> memo cleared
20.11.2014,00:00:00,$HST:EOF(logfile)