19.11.2014,13:45:24,$HST:Application just created
19.11.2014,13:45:24,$HST:SW-version 1.18, e-Callisto
19.11.2014,13:45:24,$HST:Configurationfile read
19.11.2014,13:45:24,$HST:Switched to automatic
19.11.2014,13:45:24,$HST:ATmega16 pre-configured
19.11.2014,13:45:24,$HST:Frequencyfile frq00175.cfg
19.11.2014,13:45:24,$HST:Callisto ready now...
19.11.2014,13:45:25,$HST:Measurement idle
19.11.2014,13:45:25,$HST:File scheduler.cfg read
19.11.2014,13:45:25,$HST:Measurement enable
19.11.2014,13:45:25,$CRX:AGC gain = 2.16V
19.11.2014,13:45:25,$CRX:Emitter BF199 = 0.14V
19.11.2014,13:45:25,$CRX:Analog Input = 9.24
19.11.2014,13:45:30,$HST:File frq00175.cfg read
19.11.2014,13:45:30,$HST:No calibration file found
19.11.2014,13:45:30,$HST:Plot buffer erased...
19.11.2014,13:45:30,$HST:Parametrisation RCU
19.11.2014,13:45:31,$CRX:ChargePump=On
19.11.2014,13:45:31,$HST:CD1316LV/IV detected
19.11.2014,13:45:31,$CRX:Debug=Off
19.11.2014,13:45:31,$CRX:Trigger=Extern
19.11.2014,13:45:31,$CRX:FPUcodex=25
19.11.2014,13:45:31,$CRX:GS =3480
19.11.2014,13:45:31,$CRX:GA =253
19.11.2014,13:45:31,$CRX:Delay=0msec
19.11.2014,13:45:31,$CRX:Frequency=45.0MHz
19.11.2014,13:45:31,$HST:Receiver connected
19.11.2014,13:45:31,$CRX:Sweeplength=200
19.11.2014,13:45:31,$CRX:low_band_max=171MHz
19.11.2014,13:45:31,$CRX:mid_band_max=450MHz
19.11.2014,13:45:31,$CRX:high_band_max=863MHz
19.11.2014,13:45:31,$CRX:Idle=0x
19.11.2014,13:45:31,$CRX:ChargePump=On
19.11.2014,13:45:31,$HST:CD1316LV/IV detected
19.11.2014,13:45:31,$CRX:Debug=Off
19.11.2014,13:45:31,$CRX:Trigger=Extern
19.11.2014,13:45:31,$CRX:FPUcodex=25
19.11.2014,13:45:31,$CRX:GS =3480
19.11.2014,13:45:31,$CRX:GA =624
19.11.2014,13:45:31,$CRX:Delay=0msec
19.11.2014,13:45:31,$CRX:Frequency=45.0MHz
19.11.2014,13:45:31,$HST:Receiver connected
19.11.2014,13:45:31,$CRX:Sweeplength=200
19.11.2014,13:45:31,$CRX:low_band_max=171MHz
19.11.2014,13:45:31,$CRX:mid_band_max=450MHz
19.11.2014,13:45:31,$CRX:high_band_max=863MHz
19.11.2014,13:45:31,$CRX:Idle=0x
19.11.2014,13:45:36,$HST:File FRQ00175.CFG read
19.11.2014,13:45:36,$HST:No calibration file found
19.11.2014,13:45:36,$HST:Plot buffer erased...
19.11.2014,13:45:36,$HST:Parametrisation RCU
19.11.2014,13:45:36,$CRX:ChargePump=On
19.11.2014,13:45:36,$HST:CD1316LV/IV detected
19.11.2014,13:45:36,$CRX:Debug=Off
19.11.2014,13:45:36,$CRX:Trigger=Extern
19.11.2014,13:45:36,$CRX:FPUcodex=25
19.11.2014,13:45:36,$CRX:GS =3480
19.11.2014,13:45:36,$CRX:GA =624
19.11.2014,13:45:36,$CRX:Delay=0msec
19.11.2014,13:45:36,$CRX:Frequency=45.0MHz
19.11.2014,13:45:36,$HST:Receiver connected
19.11.2014,13:45:36,$CRX:Sweeplength=200
19.11.2014,13:45:36,$CRX:low_band_max=171MHz
19.11.2014,13:45:36,$CRX:mid_band_max=450MHz
19.11.2014,13:45:36,$CRX:high_band_max=863MHz
19.11.2014,13:45:36,$CRX:Idle=0x
19.11.2014,13:45:36,$CRX:ChargePump=On
19.11.2014,13:45:36,$HST:CD1316LV/IV detected
19.11.2014,13:45:36,$CRX:Debug=Off
19.11.2014,13:45:36,$CRX:Trigger=Extern
19.11.2014,13:45:36,$CRX:FPUcodex=25
19.11.2014,13:45:36,$CRX:GS =3480
19.11.2014,13:45:36,$CRX:GA =624
19.11.2014,13:45:36,$CRX:Delay=0msec
19.11.2014,13:45:36,$CRX:Frequency=45.0MHz
19.11.2014,13:45:36,$HST:Receiver connected
19.11.2014,13:45:36,$CRX:Sweeplength=200
19.11.2014,13:45:36,$CRX:low_band_max=171MHz
19.11.2014,13:45:36,$CRX:mid_band_max=450MHz
19.11.2014,13:45:36,$CRX:high_band_max=863MHz
19.11.2014,13:45:36,$CRX:Idle=0x
19.11.2014,13:45:36,$HST:scheduler.cfg watched
19.11.2014,13:45:53,$HST:XY plot selected
19.11.2014,13:45:57,$HST:Param. RCU due to START
19.11.2014,13:45:57,$HST:Actual focuscode 25
19.11.2014,13:45:58,$HST:Enable data transfer
19.11.2014,13:45:58,$HST:Receiver calibration
19.11.2014,13:45:58,$CRX:Started
19.11.2014,13:45:58,$HST:Start new FITS-file
19.11.2014,13:45:58,$HST:Continous measurement
19.11.2014,13:59:58,$HST:Measurement stop
19.11.2014,13:59:58,$HST:FITS #1 200rows x 3360cols
19.11.2014,13:59:58,$HST:Measurement wait...
19.11.2014,13:59:58,$HST:EOT (&) detected
19.11.2014,13:59:58,$HST:Measurement halted
19.11.2014,13:59:58,$HST:Measurement stop
19.11.2014,13:59:58,$CRX:Stopped
19.11.2014,13:59:59,$HST:Measurement wait...
19.11.2014,13:59:59,$HST:Measurement halted
19.11.2014,14:00:00,$HST:Autostart via scheduler
19.11.2014,14:00:00,$HST:Param. RCU due to START
19.11.2014,14:00:00,$HST:Actual focuscode 25
19.11.2014,14:00:00,$CRX:Stopped
19.11.2014,14:00:00,$HST:Enable data transfer
19.11.2014,14:00:00,$HST:Receiver calibration
19.11.2014,14:00:00,$CRX:Started
19.11.2014,14:00:00,$HST:Start new FITS-file
19.11.2014,14:00:00,$HST:Continous measurement
19.11.2014,14:15:00,$HST:FITS #2 200rows x 3600cols
19.11.2014,14:30:00,$HST:FITS #3 200rows x 3600cols
19.11.2014,14:45:00,$HST:FITS #4 200rows x 3600cols
19.11.2014,15:00:00,$HST:FITS #5 200rows x 3600cols
19.11.2014,15:15:00,$HST:FITS #6 200rows x 3600cols
19.11.2014,15:30:00,$HST:FITS #7 200rows x 3600cols
19.11.2014,15:44:58,$HST:Measurement stop
19.11.2014,15:44:58,$HST:FITS #8 200rows x 3592cols
19.11.2014,15:44:58,$HST:Measurement wait...
19.11.2014,15:44:58,$HST:EOT (&) detected
19.11.2014,15:44:58,$HST:Measurement halted
19.11.2014,15:44:58,$HST:Measurement stop
19.11.2014,15:44:58,$CRX:Stopped
19.11.2014,15:44:58,$HST:Measurement wait...
19.11.2014,15:44:59,$HST:Measurement halted
19.11.2014,15:44:59,$HST:Measurement idle
19.11.2014,15:44:59,$CRX:Stopped
19.11.2014,15:45:00,$HST:Measurement enable
19.11.2014,15:45:00,$CRX:AGC gain = 2.16V
19.11.2014,15:45:00,$CRX:Emitter BF199 = 0.14V
19.11.2014,15:45:00,$CRX:Analog Input = 9.24
19.11.2014,15:45:01,$HST:No more entries in scheduler.
20.11.2014,00:00:00,$HST:Midnight -> memo cleared
20.11.2014,00:00:00,$HST:EOF(logfile)