18.11.2014,10:16:51,$HST:Application just created
18.11.2014,10:16:51,$HST:SW-version 1.16, e-Callisto
18.11.2014,10:16:51,$HST:Configurationfile read
18.11.2014,10:16:51,$HST:Switched to automatic
18.11.2014,10:16:51,$HST:ATmega16 pre-configured
18.11.2014,10:16:51,$HST:Frequencyfile frq00255.cfg
18.11.2014,10:16:51,$HST:Callisto ready now...
18.11.2014,10:16:51,$HST:Measurement idle
18.11.2014,10:16:52,$HST:File scheduler.cfg read
18.11.2014,10:16:52,$HST:Measurement enable
18.11.2014,10:16:52,$CRX:AGC gain = 1.79V
18.11.2014,10:16:52,$CRX:Emitter BF199 = 0.11V
18.11.2014,10:16:52,$CRX:Analog Input = 9.24
18.11.2014,10:16:57,$HST:File frq00255.cfg read
18.11.2014,10:16:57,$HST:No calibration file found
18.11.2014,10:16:57,$HST:Plot buffer erased...
18.11.2014,10:16:57,$HST:Parametrisation RCU
18.11.2014,10:16:57,$CRX:ChargePump=On
18.11.2014,10:16:57,$HST:CD1316LV/IV detected
18.11.2014,10:16:57,$CRX:Debug=Off
18.11.2014,10:16:57,$CRX:Trigger=Extern
18.11.2014,10:16:57,$CRX:FPUcodex=0
18.11.2014,10:16:57,$CRX:GS =13
18.11.2014,10:16:57,$CRX:GA =624
18.11.2014,10:16:57,$CRX:Delay=0msec
18.11.2014,10:16:57,$CRX:Frequency=45.0MHz
18.11.2014,10:16:57,$HST:Receiver connected
18.11.2014,10:16:57,$CRX:Sweeplength=200
18.11.2014,10:16:57,$CRX:low_band_max=171MHz
18.11.2014,10:16:57,$CRX:mid_band_max=450MHz
18.11.2014,10:16:57,$CRX:high_band_max=863MHz
18.11.2014,10:16:57,$CRX:Idle=0x
18.11.2014,10:16:57,$CRX:ChargePump=On
18.11.2014,10:16:57,$HST:CD1316LV/IV detected
18.11.2014,10:16:57,$CRX:Debug=Off
18.11.2014,10:16:57,$CRX:Trigger=Extern
18.11.2014,10:16:57,$CRX:FPUcodex=0
18.11.2014,10:16:57,$CRX:GS =13
18.11.2014,10:16:57,$CRX:GA =624
18.11.2014,10:16:57,$CRX:Delay=0msec
18.11.2014,10:16:57,$CRX:Frequency=45.0MHz
18.11.2014,10:16:57,$HST:Receiver connected
18.11.2014,10:16:57,$CRX:Sweeplength=200
18.11.2014,10:16:57,$CRX:low_band_max=171MHz
18.11.2014,10:16:57,$CRX:mid_band_max=450MHz
18.11.2014,10:16:57,$CRX:high_band_max=863MHz
18.11.2014,10:16:57,$CRX:Idle=0x
18.11.2014,10:17:05,$HST:XYZ plot selected
18.11.2014,10:17:06,$HST:Param. RCU due to START
18.11.2014,10:17:06,$HST:Actual focuscode 60
18.11.2014,10:17:06,$HST:Enable data transfer
18.11.2014,10:17:06,$HST:Continuous measurement
18.11.2014,10:17:06,$CRX:Started
18.11.2014,10:17:06,$HST:Start new FITS-file
18.11.2014,10:17:06,$HST:Continous measurement
18.11.2014,10:17:11,$HST:scheduler.cfg watched
18.11.2014,10:29:58,$HST:Measurement stop
18.11.2014,10:29:58,$HST:FITS #1 200rows x 3086cols
18.11.2014,10:29:58,$HST:Measurement wait...
18.11.2014,10:29:58,$HST:EOT (&) detected
18.11.2014,10:29:58,$HST:Measurement halted
18.11.2014,10:29:58,$HST:Measurement stop
18.11.2014,10:29:58,$CRX:Stopped
18.11.2014,10:29:59,$HST:Measurement wait...
18.11.2014,10:29:59,$HST:Measurement halted
18.11.2014,10:29:59,$HST:Measurement idle
18.11.2014,10:29:59,$CRX:Stopped
18.11.2014,10:30:00,$HST:Autostart via scheduler
18.11.2014,10:30:00,$HST:Param. RCU due to START
18.11.2014,10:30:00,$HST:Actual focuscode 58
18.11.2014,10:30:00,$CRX:AGC gain = 1.79V
18.11.2014,10:30:00,$CRX:Emitter BF199 = 0.12V
18.11.2014,10:30:00,$CRX:Analog Input = 9.24
18.11.2014,10:30:00,$HST:Enable data transfer
18.11.2014,10:30:00,$HST:Continuous measurement
18.11.2014,10:30:00,$CRX:Started
18.11.2014,10:30:00,$HST:Start new FITS-file
18.11.2014,10:30:00,$HST:Continous measurement
18.11.2014,10:45:00,$HST:FITS #2 200rows x 3600cols
18.11.2014,11:00:00,$HST:FITS #3 200rows x 3600cols
18.11.2014,11:15:00,$HST:FITS #4 200rows x 3600cols
18.11.2014,11:30:00,$HST:FITS #5 200rows x 3600cols
18.11.2014,11:45:00,$HST:FITS #6 200rows x 3600cols
18.11.2014,12:00:00,$HST:FITS #7 200rows x 3600cols
18.11.2014,12:15:00,$HST:FITS #8 200rows x 3600cols
18.11.2014,12:30:00,$HST:FITS #9 200rows x 3600cols
18.11.2014,12:45:00,$HST:FITS #10 200rows x 3600cols
18.11.2014,13:00:00,$HST:FITS #11 200rows x 3600cols
18.11.2014,13:15:00,$HST:FITS #12 200rows x 3600cols
18.11.2014,13:30:00,$HST:FITS #13 200rows x 3600cols
18.11.2014,13:45:00,$HST:FITS #14 200rows x 3600cols
18.11.2014,14:00:00,$HST:FITS #15 200rows x 3600cols
18.11.2014,14:15:00,$HST:FITS #16 200rows x 3600cols
18.11.2014,14:30:00,$HST:FITS #17 200rows x 3600cols
18.11.2014,14:45:00,$HST:FITS #18 200rows x 3600cols
18.11.2014,15:00:00,$HST:FITS #19 200rows x 3600cols
18.11.2014,15:15:00,$HST:FITS #20 200rows x 3600cols
18.11.2014,15:29:58,$HST:Measurement stop
18.11.2014,15:29:58,$HST:FITS #21 200rows x 3591cols
18.11.2014,15:29:58,$HST:EOT (&) detected
18.11.2014,15:29:58,$HST:Measurement wait...
18.11.2014,15:29:58,$HST:Measurement halted
18.11.2014,15:29:58,$HST:Measurement stop
18.11.2014,15:29:58,$CRX:Stopped
18.11.2014,15:29:58,$HST:Measurement wait...
18.11.2014,15:29:59,$HST:Measurement halted
18.11.2014,15:29:59,$HST:Measurement idle
18.11.2014,15:29:59,$CRX:Stopped
18.11.2014,15:29:59,$HST:Measurement enable
18.11.2014,15:29:59,$CRX:AGC gain = 1.79V
18.11.2014,15:29:59,$CRX:Emitter BF199 = 0.12V
18.11.2014,15:29:59,$CRX:Analog Input = 9.24
18.11.2014,16:14:58,$HST:Measurement stop
18.11.2014,16:14:58,$HST:Measurement wait...
18.11.2014,16:14:59,$HST:Measurement halted
18.11.2014,16:14:59,$HST:Measurement idle
18.11.2014,16:14:59,$CRX:Stopped
18.11.2014,16:14:59,$HST:Measurement enable
18.11.2014,16:14:59,$CRX:AGC gain = 1.79V
18.11.2014,16:14:59,$CRX:Emitter BF199 = 0.12V
18.11.2014,16:14:59,$CRX:Analog Input = 9.24
18.11.2014,16:15:00,$HST:Radio monitoring
18.11.2014,16:15:00,$HST:Start overview...
18.11.2014,16:15:00,$HST:Wait ~45sec please!
18.11.2014,16:15:01,$HST:No more entries in scheduler.
18.11.2014,16:15:41,$HST:End spectral overview...
18.11.2014,16:15:41,$HST:Data in log-directory
19.11.2014,00:00:00,$HST:Midnight -> memo cleared
19.11.2014,00:00:00,$HST:EOF(logfile)