30.07.2014,19:28:48,$HST:Application just created
30.07.2014,19:28:48,$HST:SW-version 1.18, e-Callisto
30.07.2014,19:28:48,$HST:Configurationfile read
30.07.2014,19:28:48,$HST:Switched to automatic
30.07.2014,19:28:48,$HST:ATmega16 pre-configured
30.07.2014,19:28:48,$HST:Frequencyfile frq00175.cfg
30.07.2014,19:28:48,$HST:Callisto ready now...
30.07.2014,19:28:49,$HST:Measurement idle
30.07.2014,19:28:49,$HST:File scheduler.cfg read
30.07.2014,19:28:49,$HST:No more entries in scheduler.
30.07.2014,19:28:49,$HST:Measurement enable
30.07.2014,19:28:49,$CRX:AGC gain = 2.18V
30.07.2014,19:28:49,$CRX:Emitter BF199 = 0.15V
30.07.2014,19:28:49,$CRX:Analog Input = 9.24
30.07.2014,19:28:52,$HST:File frq00175.cfg read
30.07.2014,19:28:52,$HST:No calibration file found
30.07.2014,19:28:52,$HST:Plot buffer erased...
30.07.2014,19:28:52,$HST:Parametrisation RCU
30.07.2014,19:28:52,$CRX:ChargePump=On
30.07.2014,19:28:52,$HST:CD1316LV/IV detected
30.07.2014,19:28:52,$CRX:Debug=Off
30.07.2014,19:28:52,$CRX:Trigger=Extern
30.07.2014,19:28:52,$CRX:FPUcodex=24
30.07.2014,19:28:52,$CRX:GS =61763
30.07.2014,19:28:52,$CRX:GA =253
30.07.2014,19:28:52,$CRX:Delay=0msec
30.07.2014,19:28:52,$CRX:Frequency=45.0MHz
30.07.2014,19:28:52,$HST:Receiver connected
30.07.2014,19:28:52,$CRX:Sweeplength=200
30.07.2014,19:28:52,$CRX:low_band_max=171MHz
30.07.2014,19:28:52,$CRX:mid_band_max=450MHz
30.07.2014,19:28:52,$CRX:high_band_max=863MHz
30.07.2014,19:28:52,$CRX:Idle=0x
30.07.2014,19:28:52,$CRX:ChargePump=On
30.07.2014,19:28:52,$HST:CD1316LV/IV detected
30.07.2014,19:28:52,$CRX:Debug=Off
30.07.2014,19:28:52,$CRX:Trigger=Extern
30.07.2014,19:28:52,$CRX:FPUcodex=24
30.07.2014,19:28:52,$CRX:GS =61763
30.07.2014,19:28:52,$CRX:GA =624
30.07.2014,19:28:52,$CRX:Delay=0msec
30.07.2014,19:28:52,$CRX:Frequency=45.0MHz
30.07.2014,19:28:52,$HST:Receiver connected
30.07.2014,19:28:52,$CRX:Sweeplength=200
30.07.2014,19:28:52,$CRX:low_band_max=171MHz
30.07.2014,19:28:52,$CRX:mid_band_max=450MHz
30.07.2014,19:28:52,$CRX:high_band_max=863MHz
30.07.2014,19:28:52,$CRX:Idle=0x
30.07.2014,19:28:55,$HST:XY plot selected
30.07.2014,19:28:59,$HST:XY plot hidden
30.07.2014,19:29:01,$HST:XY plot selected
30.07.2014,19:29:02,$HST:Param. RCU due to START
30.07.2014,19:29:02,$HST:Actual focuscode 24
30.07.2014,19:29:02,$HST:Enable data transfer
30.07.2014,19:29:02,$HST:Receiver calibration
30.07.2014,19:29:02,$CRX:Started
30.07.2014,19:29:02,$HST:Start new FITS-file
30.07.2014,19:29:03,$HST:Continous measurement
30.07.2014,19:29:16,$HST:XYZ plot selected
30.07.2014,19:29:28,$HST:XYZ plot hidden
30.07.2014,19:29:33,$HST:XY plot hidden
30.07.2014,19:29:34,$HST:Measurement stop
30.07.2014,19:29:34,$HST:FITS #1 200rows x 126cols
30.07.2014,19:29:34,$HST:Measurement wait...
30.07.2014,19:29:34,$HST:EOT (&) detected
30.07.2014,19:29:34,$HST:Measurement halted
30.07.2014,19:29:35,$HST:Measurement idle
30.07.2014,19:29:35,$CRX:Stopped
30.07.2014,19:29:35,$HST:Measurement enable
30.07.2014,19:29:35,$CRX:AGC gain = 2.38V
30.07.2014,19:29:35,$CRX:Emitter BF199 = 0.15V
30.07.2014,19:29:35,$CRX:Analog Input = 9.24
31.07.2014,00:00:00,$HST:Midnight -> memo cleared
31.07.2014,00:00:00,$HST:EOF(logfile)