18.03.2014,08:38:36,$HST:Application just created
18.03.2014,08:38:36,$HST:SW-version 1.17, e-Callisto
18.03.2014,08:38:36,$HST:Configurationfile read
18.03.2014,08:38:36,$HST:Switched to automatic
18.03.2014,08:38:36,$HST:ATmega16 pre-configured
18.03.2014,08:38:36,$HST:Frequencyfile frq00255.cfg
18.03.2014,08:38:36,$HST:Callisto ready now...
18.03.2014,08:38:37,$HST:Measurement idle
18.03.2014,08:38:37,$HST:File scheduler.cfg read
18.03.2014,08:38:37,$HST:Measurement enable
18.03.2014,08:38:43,$HST:File frq00255.cfg read
18.03.2014,08:38:43,$HST:No calibration file found
18.03.2014,08:38:43,$HST:Plot buffer erased...
18.03.2014,08:38:43,$HST:Parametrisation RCU
18.03.2014,08:38:50,$HST:File FRQ00255.CFG read
18.03.2014,08:38:50,$HST:No calibration file found
18.03.2014,08:38:50,$HST:Plot buffer erased...
18.03.2014,08:38:50,$HST:Parametrisation RCU
18.03.2014,08:38:55,$CRX:e-Callisto ETH Zurich
18.03.2014,08:38:55,$HST:Watchdog triggered -> Reset
18.03.2014,08:38:55,$CRX:V1.5, 2006-11-04
18.03.2014,08:38:56,$CRX:ChargePump=On
18.03.2014,08:38:56,$HST:CD1316LV/IV detected
18.03.2014,08:38:56,$CRX:Debug=Off
18.03.2014,08:38:56,$CRX:Trigger=No
18.03.2014,08:38:56,$CRX:FPUcodex=0
18.03.2014,08:38:56,$CRX:GS =13
18.03.2014,08:38:56,$CRX:GA =253
18.03.2014,08:38:56,$CRX:Delay=0msec
18.03.2014,08:38:56,$CRX:Frequency=0.0MHz
18.03.2014,08:38:56,$HST:Receiver connected
18.03.2014,08:38:56,$CRX:Sweeplength=0
18.03.2014,08:38:56,$CRX:low_band_max=171MHz
18.03.2014,08:38:56,$CRX:mid_band_max=450MHz
18.03.2014,08:38:56,$CRX:high_band_max=863MHz
18.03.2014,08:38:56,$CRX:Idle=0x
18.03.2014,08:38:56,$CRX:ChargePump=On
18.03.2014,08:38:56,$HST:CD1316LV/IV detected
18.03.2014,08:38:56,$CRX:Debug=Off
18.03.2014,08:38:56,$CRX:Trigger=Intern
18.03.2014,08:38:56,$CRX:FPUcodex=0
18.03.2014,08:38:56,$CRX:GS =107
18.03.2014,08:38:56,$CRX:GA =253
18.03.2014,08:38:56,$CRX:Delay=0msec
18.03.2014,08:38:56,$CRX:Frequency=45.0MHz
18.03.2014,08:38:56,$HST:Receiver connected
18.03.2014,08:38:56,$CRX:Sweeplength=200
18.03.2014,08:38:56,$CRX:low_band_max=171MHz
18.03.2014,08:38:56,$CRX:mid_band_max=450MHz
18.03.2014,08:38:56,$CRX:high_band_max=863MHz
18.03.2014,08:38:56,$CRX:Idle=0x
18.03.2014,08:38:58,$HST:Auto stop due to data loss.
18.03.2014,08:38:59,$HST:Measurement stop
18.03.2014,08:38:59,$HST:Measurement wait...
18.03.2014,08:39:00,$HST:Measurement halted
18.03.2014,08:39:00,$HST:Measurement idle
18.03.2014,08:39:00,$CRX:Stopped
18.03.2014,08:39:00,$HST:Measurement enable
18.03.2014,08:39:00,$CRX:AGC gain = 1.58V
18.03.2014,08:39:00,$CRX:Emitter BF199 = 0.13V
18.03.2014,08:39:00,$CRX:Analog Input = 9.24
18.03.2014,08:39:01,$HST:Check RS232-connection!
18.03.2014,08:39:04,$HST:Attempting Auto-Start
18.03.2014,08:39:05,$HST:Param. RCU due to START
18.03.2014,08:39:05,$HST:Actual focuscode 01
18.03.2014,08:39:05,$HST:XY plot selected
18.03.2014,08:39:05,$HST:Enable data transfer
18.03.2014,08:39:05,$HST:Receiver calibration
18.03.2014,08:39:05,$CRX:Started
18.03.2014,08:39:05,$HST:Start new FITS-file
18.03.2014,08:39:05,$HST:Continous measurement
18.03.2014,08:39:08,$HST:XYZ plot selected
18.03.2014,08:44:58,$HST:Measurement stop
18.03.2014,08:44:58,$HST:FITS #1 200rows x 1411cols
18.03.2014,08:44:58,$HST:Measurement wait...
18.03.2014,08:44:58,$HST:EOT (&) detected
18.03.2014,08:44:58,$HST:Measurement halted
18.03.2014,08:44:58,$HST:Measurement stop
18.03.2014,08:44:58,$CRX:Stopped
18.03.2014,08:44:59,$HST:Measurement wait...
18.03.2014,08:44:59,$HST:Measurement halted
18.03.2014,08:45:00,$HST:Measurement idle
18.03.2014,08:45:00,$CRX:Stopped
18.03.2014,08:45:00,$HST:Autostart via scheduler
18.03.2014,08:45:00,$HST:Param. RCU due to START
18.03.2014,08:45:00,$HST:Actual focuscode 59
18.03.2014,08:45:00,$CRX:AGC gain = 1.59V
18.03.2014,08:45:00,$CRX:Emitter BF199 = 0.13V
18.03.2014,08:45:00,$CRX:Analog Input = 9.24
18.03.2014,08:45:00,$HST:Enable data transfer
18.03.2014,08:45:00,$HST:Continuous measurement
18.03.2014,08:45:00,$CRX:Started
18.03.2014,08:45:00,$HST:Start new FITS-file
18.03.2014,08:45:00,$HST:Continous measurement
18.03.2014,09:00:00,$HST:FITS #2 200rows x 3600cols
18.03.2014,09:15:00,$HST:FITS #3 200rows x 3600cols
18.03.2014,09:30:00,$HST:FITS #4 200rows x 3600cols
18.03.2014,09:45:00,$HST:FITS #5 200rows x 3600cols
18.03.2014,10:00:00,$HST:FITS #6 200rows x 3600cols
18.03.2014,10:15:00,$HST:FITS #7 200rows x 3600cols
18.03.2014,10:30:00,$HST:FITS #8 200rows x 3600cols
18.03.2014,10:45:00,$HST:FITS #9 200rows x 3600cols
18.03.2014,11:00:00,$HST:FITS #10 200rows x 3600cols
18.03.2014,11:15:00,$HST:FITS #11 200rows x 3600cols
18.03.2014,11:29:58,$HST:Measurement stop
18.03.2014,11:29:58,$HST:FITS #12 200rows x 3591cols
18.03.2014,11:29:58,$HST:Measurement wait...
18.03.2014,11:29:58,$HST:EOT (&) detected
18.03.2014,11:29:58,$HST:Measurement halted
18.03.2014,11:29:58,$HST:Measurement stop
18.03.2014,11:29:58,$CRX:Stopped
18.03.2014,11:29:58,$HST:Measurement wait...
18.03.2014,11:29:59,$HST:Measurement halted
18.03.2014,11:29:59,$HST:Measurement idle
18.03.2014,11:29:59,$CRX:Stopped
18.03.2014,11:29:59,$HST:Measurement enable
18.03.2014,11:29:59,$CRX:AGC gain = 1.59V
18.03.2014,11:29:59,$CRX:Emitter BF199 = 0.13V
18.03.2014,11:29:59,$CRX:Analog Input = 9.24
18.03.2014,11:30:00,$HST:Autostart via scheduler
18.03.2014,11:30:00,$HST:Param. RCU due to START
18.03.2014,11:30:00,$HST:Actual focuscode 59
18.03.2014,11:30:00,$HST:Enable data transfer
18.03.2014,11:30:00,$HST:Continuous measurement
18.03.2014,11:30:00,$CRX:Started
18.03.2014,11:30:00,$HST:Start new FITS-file
18.03.2014,11:30:00,$HST:Continous measurement
18.03.2014,11:40:33,$HST:Yt plot selected
18.03.2014,11:40:36,$HST:XY plot selected
18.03.2014,11:45:00,$HST:FITS #13 200rows x 3600cols
18.03.2014,12:00:00,$HST:FITS #14 200rows x 3600cols
18.03.2014,12:15:00,$HST:FITS #15 200rows x 3600cols
18.03.2014,12:22:15,$HST:Yt plot hidden
18.03.2014,12:22:19,$HST:XYZ plot selected
18.03.2014,12:30:00,$HST:FITS #16 200rows x 3600cols
18.03.2014,12:45:00,$HST:FITS #17 200rows x 3600cols
18.03.2014,13:00:00,$HST:FITS #18 200rows x 3600cols
18.03.2014,13:15:00,$HST:FITS #19 200rows x 3600cols
18.03.2014,13:30:00,$HST:FITS #20 200rows x 3600cols
18.03.2014,13:45:00,$HST:FITS #21 200rows x 3600cols
18.03.2014,14:00:00,$HST:FITS #22 200rows x 3600cols
18.03.2014,14:15:00,$HST:FITS #23 200rows x 3600cols
18.03.2014,14:30:00,$HST:FITS #24 200rows x 3600cols
18.03.2014,14:32:39,$HST:XY plot selected
18.03.2014,14:42:38,$HST:XY plot selected
18.03.2014,14:45:00,$HST:FITS #25 200rows x 3600cols
18.03.2014,15:00:00,$HST:FITS #26 200rows x 3600cols
18.03.2014,15:15:00,$HST:FITS #27 200rows x 3600cols
18.03.2014,15:30:00,$HST:FITS #28 200rows x 3600cols
18.03.2014,15:45:00,$HST:FITS #29 200rows x 3600cols
18.03.2014,16:00:00,$HST:FITS #30 200rows x 3600cols
18.03.2014,16:15:00,$HST:FITS #31 200rows x 3600cols
18.03.2014,16:30:00,$HST:FITS #32 200rows x 3600cols
18.03.2014,16:45:00,$HST:FITS #33 200rows x 3600cols
18.03.2014,17:00:00,$HST:FITS #34 200rows x 3600cols
18.03.2014,17:14:58,$HST:Measurement stop
18.03.2014,17:14:58,$HST:FITS #35 200rows x 3592cols
18.03.2014,17:14:58,$HST:EOT (&) detected
18.03.2014,17:14:58,$HST:Measurement wait...
18.03.2014,17:14:58,$HST:Measurement halted
18.03.2014,17:14:58,$HST:Measurement stop
18.03.2014,17:14:58,$CRX:Stopped
18.03.2014,17:14:58,$HST:Measurement wait...
18.03.2014,17:14:59,$HST:Measurement halted
18.03.2014,17:14:59,$HST:Measurement idle
18.03.2014,17:14:59,$CRX:Stopped
18.03.2014,17:14:59,$HST:Measurement enable
18.03.2014,17:14:59,$CRX:AGC gain = 1.59V
18.03.2014,17:14:59,$CRX:Emitter BF199 = 0.13V
18.03.2014,17:14:59,$CRX:Analog Input = 9.24
18.03.2014,17:59:58,$HST:Measurement stop
18.03.2014,17:59:58,$HST:Measurement wait...
18.03.2014,17:59:59,$HST:Measurement halted
18.03.2014,17:59:59,$HST:Measurement idle
18.03.2014,17:59:59,$CRX:Stopped
18.03.2014,17:59:59,$HST:Measurement enable
18.03.2014,17:59:59,$CRX:AGC gain = 1.59V
18.03.2014,17:59:59,$CRX:Emitter BF199 = 0.13V
18.03.2014,17:59:59,$CRX:Analog Input = 9.24
18.03.2014,18:00:00,$HST:Radio monitoring
18.03.2014,18:00:00,$HST:Start overview...
18.03.2014,18:00:00,$HST:Wait ~45sec please!
18.03.2014,18:00:01,$HST:No more entries in scheduler.
18.03.2014,18:00:41,$HST:End spectral overview...
18.03.2014,18:00:41,$HST:Data in log-directory
19.03.2014,00:00:00,$HST:Midnight -> memo cleared
19.03.2014,00:00:00,$HST:EOF(logfile)