27.11.2013,10:12:28,$HST:Application just created
27.11.2013,10:12:28,$HST:SW-version 1.16, e-Callisto
27.11.2013,10:12:28,$HST:Configurationfile read
27.11.2013,10:12:28,$HST:Switched to automatic
27.11.2013,10:12:28,$HST:ATmega16 pre-configured
27.11.2013,10:12:28,$HST:Frequencyfile frq00255.cfg
27.11.2013,10:12:28,$HST:Callisto ready now...
27.11.2013,10:12:29,$HST:Measurement idle
27.11.2013,10:12:29,$HST:File scheduler.cfg read
27.11.2013,10:12:29,$HST:Measurement enable
27.11.2013,10:12:29,$CRX:AGC gain = 2.18V
27.11.2013,10:12:29,$CRX:Emitter BF199 = 0.11V
27.11.2013,10:12:29,$CRX:Analog Input = 9.24
27.11.2013,10:12:35,$HST:File frq00255.cfg read
27.11.2013,10:12:35,$HST:No calibration file found
27.11.2013,10:12:35,$HST:Plot buffer erased...
27.11.2013,10:12:35,$HST:Parametrisation RCU
27.11.2013,10:12:35,$CRX:ChargePump=On
27.11.2013,10:12:35,$HST:CD1316LV/IV detected
27.11.2013,10:12:35,$CRX:Debug=Off
27.11.2013,10:12:35,$CRX:Trigger=Soft
27.11.2013,10:12:35,$CRX:FPUcodex=59
27.11.2013,10:12:35,$CRX:GS =3394
27.11.2013,10:12:35,$CRX:GA =253
27.11.2013,10:12:35,$CRX:Delay=2msec
27.11.2013,10:12:35,$CRX:Frequency=870.0MHz
27.11.2013,10:12:35,$HST:Receiver connected
27.11.2013,10:12:35,$CRX:Sweeplength=200
27.11.2013,10:12:35,$CRX:low_band_max=171MHz
27.11.2013,10:12:35,$CRX:mid_band_max=450MHz
27.11.2013,10:12:35,$CRX:high_band_max=863MHz
27.11.2013,10:12:35,$CRX:Idle=0x
27.11.2013,10:12:35,$CRX:ChargePump=On
27.11.2013,10:12:35,$HST:CD1316LV/IV detected
27.11.2013,10:12:35,$CRX:Debug=Off
27.11.2013,10:12:35,$CRX:Trigger=Extern
27.11.2013,10:12:35,$CRX:FPUcodex=59
27.11.2013,10:12:35,$CRX:GS =3394
27.11.2013,10:12:35,$CRX:GA =624
27.11.2013,10:12:35,$CRX:Delay=2msec
27.11.2013,10:12:35,$CRX:Frequency=45.0MHz
27.11.2013,10:12:35,$HST:Receiver connected
27.11.2013,10:12:35,$CRX:Sweeplength=200
27.11.2013,10:12:35,$CRX:low_band_max=171MHz
27.11.2013,10:12:35,$CRX:mid_band_max=450MHz
27.11.2013,10:12:35,$CRX:high_band_max=863MHz
27.11.2013,10:12:35,$CRX:Idle=0x
27.11.2013,10:12:40,$HST:scheduler.cfg watched
27.11.2013,10:12:44,$HST:Param. RCU due to START
27.11.2013,10:12:44,$HST:Actual focuscode 59
27.11.2013,10:12:44,$HST:Enable data transfer
27.11.2013,10:12:44,$HST:Continuous measurement
27.11.2013,10:12:44,$CRX:Started
27.11.2013,10:12:44,$HST:Start new FITS-file
27.11.2013,10:12:45,$HST:XY plot selected
27.11.2013,10:12:45,$HST:Continous measurement