27.11.2013,10:41:54,$HST:Application just created
27.11.2013,10:41:54,$HST:SW-version 1.18, e-Callisto
27.11.2013,10:41:54,$HST:Configurationfile read
27.11.2013,10:41:54,$HST:Switched to automatic
27.11.2013,10:41:54,$HST:ATmega16 pre-configured
27.11.2013,10:41:54,$HST:Frequencyfile frq00175.cfg
27.11.2013,10:41:54,$HST:Callisto ready now...
27.11.2013,10:41:55,$HST:Measurement idle
27.11.2013,10:41:55,$HST:File scheduler.cfg read
27.11.2013,10:41:55,$HST:Measurement enable
27.11.2013,10:41:55,$CRX:AGC gain = 2.35V
27.11.2013,10:41:55,$CRX:Emitter BF199 = 0.14V
27.11.2013,10:41:55,$CRX:Analog Input = 9.24
27.11.2013,10:42:01,$HST:File frq00175.cfg read
27.11.2013,10:42:01,$HST:No calibration file found
27.11.2013,10:42:01,$HST:Plot buffer erased...
27.11.2013,10:42:01,$HST:Parametrisation RCU
27.11.2013,10:42:01,$CRX:ChargePump=On
27.11.2013,10:42:01,$HST:CD1316LV/IV detected
27.11.2013,10:42:01,$CRX:Debug=Off
27.11.2013,10:42:01,$CRX:Trigger=Extern
27.11.2013,10:42:01,$CRX:FPUcodex=25
27.11.2013,10:42:01,$CRX:GS =3376
27.11.2013,10:42:01,$CRX:GA =253
27.11.2013,10:42:01,$CRX:Delay=0msec
27.11.2013,10:42:01,$CRX:Frequency=45.0MHz
27.11.2013,10:42:01,$HST:Receiver connected
27.11.2013,10:42:01,$CRX:Sweeplength=200
27.11.2013,10:42:01,$CRX:low_band_max=171MHz
27.11.2013,10:42:01,$CRX:mid_band_max=450MHz
27.11.2013,10:42:01,$CRX:high_band_max=863MHz
27.11.2013,10:42:01,$CRX:Idle=0x
27.11.2013,10:42:01,$CRX:ChargePump=On
27.11.2013,10:42:01,$HST:CD1316LV/IV detected
27.11.2013,10:42:01,$CRX:Debug=Off
27.11.2013,10:42:01,$CRX:Trigger=Extern
27.11.2013,10:42:01,$CRX:FPUcodex=25
27.11.2013,10:42:01,$CRX:GS =3393
27.11.2013,10:42:01,$CRX:GA =253
27.11.2013,10:42:01,$CRX:Delay=0msec
27.11.2013,10:42:01,$CRX:Frequency=45.0MHz
27.11.2013,10:42:01,$HST:Receiver connected
27.11.2013,10:42:01,$CRX:Sweeplength=200
27.11.2013,10:42:01,$CRX:low_band_max=171MHz
27.11.2013,10:42:01,$CRX:mid_band_max=450MHz
27.11.2013,10:42:01,$CRX:high_band_max=863MHz
27.11.2013,10:42:01,$CRX:Idle=0x
27.11.2013,10:42:07,$HST:File FRQ00175.CFG read
27.11.2013,10:42:07,$HST:No calibration file found
27.11.2013,10:42:07,$HST:Plot buffer erased...
27.11.2013,10:42:07,$HST:Parametrisation RCU
27.11.2013,10:48:22,$HST:XY plot selected
27.11.2013,10:48:23,$HST:Param. RCU due to START
27.11.2013,10:48:23,$HST:Actual focuscode 25
27.11.2013,10:48:23,$HST:Enable data transfer
27.11.2013,10:48:23,$HST:Receiver calibration
27.11.2013,10:48:23,$HST:Start new FITS-file
27.11.2013,10:48:23,$HST:Continous measurement
27.11.2013,10:48:31,$HST:All threads terminated
27.11.2013,10:48:31,$HST:This application closed