2/7/2013,14:38:01,$HST:Application just created
2/7/2013,14:38:01,$HST:SW-version 1.09, e-Callisto
2/7/2013,14:38:01,$HST:Configurationfile read
2/7/2013,14:38:01,$HST:Switched to automatic
2/7/2013,14:38:01,$HST:ATmega16 pre-configured
2/7/2013,14:38:01,$HST:Frequencyfile frq00999.cfg
2/7/2013,14:38:01,$HST:Callisto ready now...
2/7/2013,14:38:02,$HST:Measurement idle
2/7/2013,14:38:02,$HST:File scheduler.cfg read
2/7/2013,14:38:02,$HST:Measurement enable
2/7/2013,14:38:02,$CRX:AGC gain = 0.00V
2/7/2013,14:38:02,$CRX:Emitter BF199 = 0.14V
2/7/2013,14:38:02,$CRX:Analog Input = 9.24
2/7/2013,14:38:07,$HST:File frq00999.cfg read
2/7/2013,14:38:07,$HST:No calibration file found
2/7/2013,14:38:07,$HST:Plot buffer erased...
2/7/2013,14:38:07,$HST:Parametrisation RCU
2/7/2013,14:38:08,$HST:XY plot selected
2/7/2013,14:38:13,$HST:Param. RCU due to START
2/7/2013,14:38:13,$HST:Actual focuscode 25
2/7/2013,14:38:13,$HST:Enable data transfer
2/7/2013,14:38:13,$HST:Receiver calibration
2/7/2013,14:38:13,$CRX:Started
2/7/2013,14:38:13,$HST:Start new FITS-file
2/7/2013,14:38:13,$HST:Continous measurement
2/7/2013,14:39:10,$HST:XY plot hidden
2/7/2013,14:39:10,$HST:XYZ plot selected
2/7/2013,14:53:13,$HST:FITS #1 200rows x 3600cols
2/7/2013,15:08:23,$HST:FITS #2 200rows x 3600cols
2/7/2013,15:23:23,$HST:FITS #3 200rows x 3600cols
2/7/2013,15:38:23,$HST:FITS #4 200rows x 3600cols
2/7/2013,15:53:23,$HST:FITS #5 200rows x 3600cols
2/7/2013,15:59:56,$HST:Measurement stop
2/7/2013,15:59:56,$HST:FITS #6 200rows x 1570cols
2/7/2013,15:59:56,$HST:Measurement wait...
2/7/2013,15:59:56,$HST:Auto stop due to data loss.
2/7/2013,15:59:56,$HST:Check RS232-connection!
2/7/2013,15:59:56,$HST:Auto stop due to data loss.
2/7/2013,15:59:56,$HST:Check RS232-connection!
2/7/2013,15:59:56,$HST:EOT (&) detected
2/7/2013,15:59:56,$HST:Measurement stop
2/7/2013,15:59:56,$HST:Measurement wait...
2/7/2013,15:59:57,$HST:Measurement halted
2/7/2013,15:59:57,$HST:Measurement idle
2/7/2013,15:59:57,$CRX:Stopped
2/7/2013,15:59:57,$HST:Measurement enable
2/7/2013,15:59:57,$CRX:AGC gain = 1.76V
2/7/2013,15:59:57,$CRX:Emitter BF199 = 0.14V
2/7/2013,15:59:57,$CRX:Analog Input = 9.24
2/7/2013,16:00:01,$HST:No more entries in scheduler.
2/8/2013,00:00:00,$HST:Midnight -> memo cleared
2/8/2013,00:00:00,$HST:EOF(logfile)