1/23/2013,13:03:11,$HST:Application just created
1/23/2013,13:03:11,$HST:SW-version 1.09, e-Callisto
1/23/2013,13:03:11,$HST:Configurationfile read
1/23/2013,13:03:11,$HST:Switched to automatic
1/23/2013,13:03:11,$HST:ATmega16 pre-configured
1/23/2013,13:03:11,$HST:Frequencyfile frq00999.cfg
1/23/2013,13:03:11,$HST:Callisto ready now...
1/23/2013,13:03:13,$HST:Measurement idle
1/23/2013,13:03:13,$HST:File scheduler.cfg read
1/23/2013,13:03:13,$HST:Measurement enable
1/23/2013,13:03:13,$CRX:AGC gain = 1.78V
1/23/2013,13:03:13,$CRX:Emitter BF199 = 0.15V
1/23/2013,13:03:13,$CRX:Analog Input = 9.24
1/23/2013,13:03:19,$HST:File frq00999.cfg read
1/23/2013,13:03:19,$HST:No calibration file found
1/23/2013,13:03:19,$HST:Plot buffer erased...
1/23/2013,13:03:19,$HST:Parametrisation RCU
1/23/2013,13:03:23,$HST:Param. RCU due to START
1/23/2013,13:03:23,$HST:Actual focuscode 24
1/23/2013,13:03:23,$HST:Enable data transfer
1/23/2013,13:03:23,$HST:Receiver calibration
1/23/2013,13:03:23,$CRX:Started
1/23/2013,13:03:23,$HST:Start new FITS-file
1/23/2013,13:03:23,$HST:Continous measurement
1/23/2013,13:03:24,$HST:XY plot selected
1/23/2013,13:03:47,$HST:XYZ plot selected
1/23/2013,13:18:30,$HST:FITS #1 200rows x 3600cols
1/23/2013,13:33:31,$HST:FITS #2 200rows x 3600cols
1/23/2013,13:48:31,$HST:FITS #3 200rows x 3600cols
1/23/2013,14:03:31,$HST:FITS #4 200rows x 3600cols
1/23/2013,14:18:31,$HST:FITS #5 200rows x 3600cols
1/23/2013,14:33:31,$HST:FITS #6 200rows x 3600cols
1/23/2013,14:48:31,$HST:FITS #7 200rows x 3600cols
1/23/2013,15:03:31,$HST:FITS #8 200rows x 3600cols
1/23/2013,15:18:32,$HST:FITS #9 200rows x 3600cols
1/23/2013,15:33:31,$HST:FITS #10 200rows x 3600cols
1/23/2013,15:44:56,$HST:Measurement stop
1/23/2013,15:44:56,$HST:FITS #11 200rows x 2737cols
1/23/2013,15:44:56,$HST:Measurement wait...
1/23/2013,15:44:56,$HST:Auto stop due to data loss.
1/23/2013,15:44:56,$HST:Check RS232-connection!
1/23/2013,15:44:56,$HST:Auto stop due to data loss.
1/23/2013,15:44:56,$HST:Check RS232-connection!
1/23/2013,15:44:56,$HST:EOT (&) detected
1/23/2013,15:44:56,$HST:Measurement stop
1/23/2013,15:44:56,$HST:Measurement wait...
1/23/2013,15:44:58,$HST:Measurement halted
1/23/2013,15:44:58,$HST:Measurement idle
1/23/2013,15:44:58,$CRX:Stopped
1/23/2013,15:44:58,$HST:Measurement enable
1/23/2013,15:44:58,$CRX:AGC gain = 1.78V
1/23/2013,15:44:58,$CRX:Emitter BF199 = 0.15V
1/23/2013,15:44:58,$CRX:Analog Input = 9.24
1/23/2013,15:45:01,$HST:No more entries in scheduler.
1/24/2013,00:00:00,$HST:Midnight -> memo cleared
1/24/2013,00:00:00,$HST:EOF(logfile)