11/5/2012,13:11:51,$HST:Application just created
11/5/2012,13:11:51,$HST:SW-version 1.09, e-Callisto
11/5/2012,13:11:51,$HST:Configurationfile read
11/5/2012,13:11:51,$HST:Switched to automatic
11/5/2012,13:11:51,$HST:ATmega16 pre-configured
11/5/2012,13:11:51,$HST:Frequencyfile frq00999.cfg
11/5/2012,13:11:51,$HST:Callisto ready now...
11/5/2012,13:11:53,$HST:Measurement idle
11/5/2012,13:11:53,$HST:File scheduler.cfg read
11/5/2012,13:11:53,$HST:Measurement enable
11/5/2012,13:11:53,$CRX:AGC gain = 0.00V
11/5/2012,13:11:53,$CRX:Emitter BF199 = 0.14V
11/5/2012,13:11:53,$CRX:Analog Input = 9.24
11/5/2012,13:11:59,$HST:File frq00999.cfg read
11/5/2012,13:11:59,$HST:No calibration file found
11/5/2012,13:11:59,$HST:Plot buffer erased...
11/5/2012,13:11:59,$HST:Parametrisation RCU
11/5/2012,13:14:15,$HST:Param. RCU due to START
11/5/2012,13:14:15,$HST:Actual focuscode 25
11/5/2012,13:14:15,$HST:Enable data transfer
11/5/2012,13:14:15,$HST:Receiver calibration
11/5/2012,13:14:15,$CRX:Started
11/5/2012,13:14:15,$HST:Start new FITS-file
11/5/2012,13:14:15,$HST:Continous measurement
11/5/2012,13:14:16,$HST:XY plot selected
11/5/2012,13:29:15,$HST:FITS #1 200rows x 3600cols
11/5/2012,13:44:15,$HST:FITS #2 200rows x 3600cols
11/5/2012,13:57:26,$HST:XYZ plot selected
11/5/2012,13:59:15,$HST:FITS #3 200rows x 3600cols
11/5/2012,14:14:16,$HST:FITS #4 200rows x 3600cols
11/5/2012,14:29:16,$HST:FITS #5 200rows x 3600cols
11/5/2012,14:44:16,$HST:FITS #6 200rows x 3600cols
11/5/2012,14:59:16,$HST:FITS #7 200rows x 3600cols
11/5/2012,15:14:16,$HST:FITS #8 200rows x 3600cols
11/5/2012,15:29:16,$HST:FITS #9 200rows x 3600cols
11/5/2012,15:29:56,$HST:Measurement stop
11/5/2012,15:29:56,$HST:FITS #10 200rows x 160cols
11/5/2012,15:29:56,$HST:Measurement wait...
11/5/2012,15:29:56,$HST:Auto stop due to data loss.
11/5/2012,15:29:56,$HST:Check RS232-connection!
11/5/2012,15:29:56,$HST:Auto stop due to data loss.
11/5/2012,15:29:56,$HST:Check RS232-connection!
11/5/2012,15:29:56,$HST:EOT (&) detected
11/5/2012,15:29:56,$HST:Measurement stop
11/5/2012,15:29:56,$HST:Measurement wait...
11/5/2012,15:29:57,$HST:Measurement halted
11/5/2012,15:29:57,$HST:Measurement idle
11/5/2012,15:29:57,$CRX:Stopped
11/5/2012,15:29:57,$HST:Measurement enable
11/5/2012,15:29:57,$CRX:AGC gain = 1.76V
11/5/2012,15:29:57,$CRX:Emitter BF199 = 0.14V
11/5/2012,15:29:57,$CRX:Analog Input = 9.24
11/5/2012,15:30:01,$HST:No more entries in scheduler.
11/6/2012,00:00:00,$HST:Midnight -> memo cleared
11/6/2012,00:00:00,$HST:EOF(logfile)