8/2/2012,16:14:03,$HST:Application just created
8/2/2012,16:14:03,$HST:SW-version 1.09, e-Callisto
8/2/2012,16:14:03,$HST:Configurationfile read
8/2/2012,16:14:03,$HST:Switched to automatic
8/2/2012,16:14:03,$HST:ATmega16 pre-configured
8/2/2012,16:14:03,$HST:Frequencyfile frq00806.cfg
8/2/2012,16:14:03,$HST:Callisto ready now...
8/2/2012,16:14:04,$HST:Measurement idle
8/2/2012,16:14:04,
8/2/2012,16:14:04,$CRX:V1.5, 2006-11-04
8/2/2012,16:14:04,$HST:File scheduler.cfg read
8/2/2012,16:14:04,$HST:Measurement enable
8/2/2012,16:14:04,$CRX:AGC gain = 0.00V
8/2/2012,16:14:04,$CRX:Emitter BF199 = 0.14V
8/2/2012,16:14:04,$CRX:Analog Input = 9.24
8/2/2012,16:14:06,$HST:XY plot selected
8/2/2012,16:14:10,$HST:File frq00806.cfg read
8/2/2012,16:14:10,$HST:File CAL00806.prn read
8/2/2012,16:14:10,$HST:Plot buffer erased...
8/2/2012,16:14:10,$HST:Parametrisation RCU
8/2/2012,16:14:11,$HST:Param. RCU due to START
8/2/2012,16:14:11,$HST:Actual focuscode 25
8/2/2012,16:14:11,$HST:Enable data transfer
8/2/2012,16:14:11,$HST:Receiver calibration
8/2/2012,16:14:11,$CRX:Started
8/2/2012,16:14:11,$HST:Start new FITS-file
8/2/2012,16:14:11,$HST:Continous measurement
8/2/2012,16:29:11,$HST:FITS #1 200rows x 3600cols
8/2/2012,16:44:11,$HST:FITS #2 200rows x 3600cols
8/2/2012,16:59:11,$HST:FITS #3 200rows x 3600cols
8/2/2012,17:14:11,$HST:FITS #4 200rows x 3600cols
8/2/2012,17:29:11,$HST:FITS #5 200rows x 3600cols
8/2/2012,17:44:11,$HST:FITS #6 200rows x 3600cols
8/2/2012,17:59:11,$HST:FITS #7 200rows x 3600cols
8/2/2012,18:14:11,$HST:FITS #8 200rows x 3600cols
8/2/2012,18:29:11,$HST:FITS #9 200rows x 3600cols
8/2/2012,18:29:56,$HST:Measurement stop
8/2/2012,18:29:56,$HST:FITS #10 200rows x 178cols
8/2/2012,18:29:56,$HST:Measurement wait...
8/2/2012,18:29:56,$HST:Auto stop due to data loss.
8/2/2012,18:29:56,$HST:Check RS232-connection!
8/2/2012,18:29:56,$HST:Auto stop due to data loss.
8/2/2012,18:29:56,$HST:Check RS232-connection!
8/2/2012,18:29:56,$HST:EOT (&) detected
8/2/2012,18:29:56,$HST:Measurement stop
8/2/2012,18:29:56,$HST:Measurement wait...
8/2/2012,18:29:57,$HST:Measurement halted
8/2/2012,18:29:57,$HST:Measurement idle
8/2/2012,18:29:57,$CRX:Stopped
8/2/2012,18:29:57,$HST:Measurement enable
8/2/2012,18:29:57,$CRX:AGC gain = 1.76V
8/2/2012,18:29:57,$CRX:Emitter BF199 = 0.14V
8/2/2012,18:29:57,$CRX:Analog Input = 9.24
8/2/2012,18:30:01,$HST:No more entries in scheduler.
8/3/2012,00:00:00,$HST:Midnight -> memo cleared
8/3/2012,00:00:00,$HST:EOF(logfile)