3/28/2012,13:28:07,$HST:Application just created
3/28/2012,13:28:07,$HST:SW-version 1.09, e-Callisto
3/28/2012,13:28:07,$HST:Configurationfile read
3/28/2012,13:28:07,$HST:Switched to automatic
3/28/2012,13:28:07,$HST:ATmega16 pre-configured
3/28/2012,13:28:07,$HST:Frequencyfile frq00806.cfg
3/28/2012,13:28:07,$HST:Callisto ready now...
3/28/2012,13:28:09,$HST:Measurement idle
3/28/2012,13:28:09,$HST:File scheduler.cfg read
3/28/2012,13:28:09,$HST:Measurement enable
3/28/2012,13:28:09,$CRX:AGC gain = 1.78V
3/28/2012,13:28:09,$CRX:Emitter BF199 = 0.15V
3/28/2012,13:28:09,$CRX:Analog Input = 9.24
3/28/2012,13:28:14,$HST:File frq00806.cfg read
3/28/2012,13:28:15,$HST:File CAL00806.prn read
3/28/2012,13:28:15,$HST:Plot buffer erased...
3/28/2012,13:28:15,$HST:Parametrisation RCU
3/28/2012,13:30:17,$HST:XY plot selected
3/28/2012,13:30:26,$HST:Param. RCU due to START
3/28/2012,13:30:26,$HST:Actual focuscode 24
3/28/2012,13:30:26,$HST:Enable data transfer
3/28/2012,13:30:26,$HST:Receiver calibration
3/28/2012,13:30:26,$CRX:Started
3/28/2012,13:30:26,$HST:Start new FITS-file
3/28/2012,13:30:26,$HST:Continous measurement
3/28/2012,13:30:29,$HST:Yt plot selected
3/28/2012,13:46:20,$HST:FITS #1 200rows x 3600cols
3/28/2012,14:01:21,$HST:FITS #2 200rows x 3600cols
3/28/2012,14:16:35,$HST:FITS #3 200rows x 3600cols
3/28/2012,14:31:35,$HST:FITS #4 200rows x 3600cols
3/28/2012,14:46:35,$HST:FITS #5 200rows x 3600cols
3/28/2012,15:01:40,$HST:FITS #6 200rows x 3600cols
3/28/2012,15:16:40,$HST:FITS #7 200rows x 3600cols
3/28/2012,15:31:40,$HST:FITS #8 200rows x 3600cols
3/28/2012,15:46:40,$HST:FITS #9 200rows x 3600cols
3/28/2012,16:01:40,$HST:FITS #10 200rows x 3600cols
3/28/2012,16:16:40,$HST:FITS #11 200rows x 3600cols
3/28/2012,16:31:40,$HST:FITS #12 200rows x 3600cols
3/28/2012,16:46:40,$HST:FITS #13 200rows x 3600cols
3/28/2012,17:01:40,$HST:FITS #14 200rows x 3600cols
3/28/2012,17:14:56,$HST:Measurement stop
3/28/2012,17:14:56,$HST:FITS #15 200rows x 3183cols
3/28/2012,17:14:56,$HST:Auto stop due to data loss.
3/28/2012,17:14:56,$HST:Check RS232-connection!
3/28/2012,17:14:56,$HST:Auto stop due to data loss.
3/28/2012,17:14:56,$HST:Check RS232-connection!
3/28/2012,17:14:56,$HST:EOT (&) detected
3/28/2012,17:14:57,$HST:Measurement stop
3/28/2012,17:14:57,$HST:Measurement wait...
3/28/2012,17:14:58,$HST:Measurement halted
3/28/2012,17:14:58,$CRX:Stopped
3/28/2012,17:14:58,$HST:Measurement idle
3/28/2012,17:14:58,$HST:Measurement enable
3/28/2012,17:14:58,$CRX:AGC gain = 1.78V
3/28/2012,17:14:58,$CRX:Emitter BF199 = 0.15V
3/28/2012,17:14:58,$CRX:Analog Input = 9.24
3/28/2012,17:15:01,$HST:No more entries in scheduler.
3/29/2012,00:00:00,$HST:Midnight -> memo cleared
3/29/2012,00:00:00,$HST:EOF(logfile)