1/13/2012,13:58:42,$HST:Application just created
1/13/2012,13:58:42,$HST:SW-version 1.09, e-Callisto
1/13/2012,13:58:42,$HST:Configurationfile read
1/13/2012,13:58:42,$HST:Switched to automatic
1/13/2012,13:58:42,$HST:ATmega16 pre-configured
1/13/2012,13:58:42,$HST:Frequencyfile frq00806.cfg
1/13/2012,13:58:42,$HST:Callisto ready now...
1/13/2012,13:58:43,$HST:Measurement idle
1/13/2012,13:58:43,$HST:File scheduler.cfg read
1/13/2012,13:58:43,$HST:Measurement enable
1/13/2012,13:58:43,$CRX:AGC gain = 0.00V
1/13/2012,13:58:43,$CRX:Emitter BF199 = 0.14V
1/13/2012,13:58:43,$CRX:Analog Input = 9.24
1/13/2012,13:58:48,$HST:File frq00806.cfg read
1/13/2012,13:58:48,$HST:File CAL00806.prn read
1/13/2012,13:58:48,$HST:Plot buffer erased...
1/13/2012,13:58:48,$HST:Parametrisation RCU
1/13/2012,13:58:53,$HST:XY plot selected
1/13/2012,13:58:54,$HST:Param. RCU due to START
1/13/2012,13:58:54,$HST:Actual focuscode 25
1/13/2012,13:58:54,$HST:Enable data transfer
1/13/2012,13:58:54,$HST:Receiver calibration
1/13/2012,13:58:54,$CRX:Started
1/13/2012,13:58:54,$HST:Start new FITS-file
1/13/2012,13:58:54,$HST:Continous measurement
1/13/2012,14:13:54,$HST:FITS #1 200rows x 3600cols
1/13/2012,14:28:54,$HST:FITS #2 200rows x 3600cols
1/13/2012,14:43:54,$HST:FITS #3 200rows x 3600cols
1/13/2012,14:58:54,$HST:FITS #4 200rows x 3600cols
1/13/2012,15:13:54,$HST:FITS #5 200rows x 3600cols
1/13/2012,15:28:54,$HST:FITS #6 200rows x 3600cols
1/13/2012,15:29:56,$HST:Measurement stop
1/13/2012,15:29:56,$HST:FITS #7 200rows x 247cols
1/13/2012,15:29:56,$HST:Measurement wait...
1/13/2012,15:29:56,$HST:Auto stop due to data loss.
1/13/2012,15:29:56,$HST:Check RS232-connection!
1/13/2012,15:29:56,$HST:Auto stop due to data loss.
1/13/2012,15:29:56,$HST:Check RS232-connection!
1/13/2012,15:29:56,$HST:EOT (&) detected
1/13/2012,15:29:56,$HST:Measurement stop
1/13/2012,15:29:56,$HST:Measurement wait...
1/13/2012,15:29:57,$HST:Measurement halted
1/13/2012,15:29:57,$HST:Measurement idle
1/13/2012,15:29:57,$CRX:Stopped
1/13/2012,15:29:57,$HST:Measurement enable
1/13/2012,15:29:57,$CRX:AGC gain = 1.76V
1/13/2012,15:29:57,$CRX:Emitter BF199 = 0.14V
1/13/2012,15:29:57,$CRX:Analog Input = 9.24
1/13/2012,15:30:01,$HST:No more entries in scheduler.
1/14/2012,00:00:00,$HST:Midnight -> memo cleared
1/14/2012,00:00:00,$HST:EOF(logfile)