13.09.2011,19:47:44,$HST:Application just created
13.09.2011,19:47:44,$HST:SW-version 1.09, e-Callisto
13.09.2011,19:47:44,$HST:Configurationfile read
13.09.2011,19:47:44,$HST:Switched to automatic
13.09.2011,19:47:44,$HST:ATmega16 pre-configured
13.09.2011,19:47:44,$HST:Frequencyfile frq00306.cfg
13.09.2011,19:47:44,$HST:Callisto ready now...
13.09.2011,19:47:45,$HST:Measurement idle
13.09.2011,19:47:45,$HST:File scheduler.cfg read
13.09.2011,19:47:45,$HST:No more entries in scheduler.
13.09.2011,19:47:45,$HST:Measurement enable
13.09.2011,19:47:45,$CRX:AGC gain = 2.18V
13.09.2011,19:47:45,$CRX:Emitter BF199 = 0.12V
13.09.2011,19:47:45,$CRX:Analog Input = 9.24
13.09.2011,19:47:46,$HST:File frq00306.cfg read
13.09.2011,19:47:46,$HST:No calibration file found
13.09.2011,19:47:46,$HST:Plot buffer erased...
13.09.2011,19:47:46,$HST:Parametrisation RCU
13.09.2011,19:47:49,$HST:XY plot selected
13.09.2011,19:47:53,$HST:Param. RCU due to START
13.09.2011,19:47:53,$HST:Actual focuscode 59
13.09.2011,19:47:53,$HST:Enable data transfer
13.09.2011,19:47:53,$HST:Continuous measurement
13.09.2011,19:47:53,$CRX:Started
13.09.2011,19:47:53,$HST:Start new FITS-file
13.09.2011,19:47:53,$HST:Continous measurement
13.09.2011,19:48:25,$HST:Measurement stop
13.09.2011,19:48:25,$HST:FITS #1 100rows x 262cols
13.09.2011,19:48:26,$HST:Measurement wait...
13.09.2011,19:48:26,$HST:Auto stop due to data loss.
13.09.2011,19:48:26,$HST:Check RS232-connection!
13.09.2011,19:48:26,$HST:Auto stop due to data loss.
13.09.2011,19:48:26,$HST:Check RS232-connection!
13.09.2011,19:48:26,$HST:EOT (&) detected
13.09.2011,19:48:26,$HST:Measurement stop
13.09.2011,19:48:26,$HST:Measurement wait...
13.09.2011,19:48:26,$HST:Measurement halted
13.09.2011,19:48:26,$CRX:Stopped
13.09.2011,19:48:26,$HST:Measurement idle
13.09.2011,19:48:26,$HST:Measurement enable
13.09.2011,19:48:26,$CRX:AGC gain = 2.18V
13.09.2011,19:48:26,$CRX:Emitter BF199 = 0.12V
13.09.2011,19:48:26,$CRX:Analog Input = 9.24
14.09.2011,00:00:00,$HST:Midnight -> memo cleared
14.09.2011,00:00:00,$HST:EOF(logfile)