02.07.2011,21:13:35,$HST:Application just created
02.07.2011,21:13:35,$HST:SW-version 1.09, e-Callisto
02.07.2011,21:13:35,$HST:Configurationfile read
02.07.2011,21:13:35,$HST:Switched to automatic
02.07.2011,21:13:35,$HST:ATmega16 pre-configured
02.07.2011,21:13:35,$HST:Frequencyfile frq00306.cfg
02.07.2011,21:13:35,$HST:Callisto ready now...
02.07.2011,21:13:37,$HST:Measurement idle
02.07.2011,21:13:37,$HST:File scheduler.cfg read
02.07.2011,21:13:37,$HST:No more entries in scheduler.
02.07.2011,21:13:37,$HST:Measurement enable
02.07.2011,21:13:37,$CRX:AGC gain = 2.18V
02.07.2011,21:13:37,$CRX:Emitter BF199 = 0.12V
02.07.2011,21:13:37,$CRX:Analog Input = 9.24
02.07.2011,21:13:40,$HST:File frq00306.cfg read
02.07.2011,21:13:40,$HST:No calibration file found
02.07.2011,21:13:40,$HST:Plot buffer erased...
02.07.2011,21:13:40,$HST:Parametrisation RCU
02.07.2011,21:13:43,$HST:XY plot selected
02.07.2011,21:13:44,$HST:Param. RCU due to START
02.07.2011,21:13:44,$HST:Actual focuscode 59
02.07.2011,21:13:45,$HST:Enable data transfer
02.07.2011,21:13:45,$HST:Continuous measurement
02.07.2011,21:13:45,$CRX:Started
02.07.2011,21:13:45,$HST:Start new FITS-file
02.07.2011,21:13:45,$HST:Continous measurement
02.07.2011,21:13:50,$HST:Measurement stop
02.07.2011,21:13:50,$HST:FITS #1 100rows x 39cols
02.07.2011,21:13:50,$HST:Auto stop due to data loss.
02.07.2011,21:13:50,$HST:Check RS232-connection!
02.07.2011,21:13:50,$HST:Auto stop due to data loss.
02.07.2011,21:13:50,$HST:Check RS232-connection!
02.07.2011,21:13:50,$HST:EOT (&) detected
02.07.2011,21:13:51,$HST:Measurement stop
02.07.2011,21:13:51,$HST:Measurement wait...
02.07.2011,21:13:51,$HST:Measurement halted
02.07.2011,21:13:52,$HST:Measurement idle
02.07.2011,21:13:52,$CRX:Stopped
02.07.2011,21:13:52,$HST:Measurement enable
02.07.2011,21:13:52,$CRX:AGC gain = 2.18V
02.07.2011,21:13:52,$CRX:Emitter BF199 = 0.12V
02.07.2011,21:13:52,$CRX:Analog Input = 9.24
03.07.2011,00:00:00,$HST:Midnight -> memo cleared
03.07.2011,00:00:00,$HST:EOF(logfile)