01/02/2011,13:32:20,$HST:Application just created
01/02/2011,13:32:20,$HST:SW-version 1.09, e-Callisto
01/02/2011,13:32:20,$HST:Configurationfile read
01/02/2011,13:32:20,$HST:Switched to automatic
01/02/2011,13:32:20,$HST:ATmega16 pre-configured
01/02/2011,13:32:20,$HST:Frequencyfile frq05005.cfg
01/02/2011,13:32:20,$HST:Callisto ready now...
01/02/2011,13:32:21,$HST:Measurement idle
01/02/2011,13:32:21,$HST:File scheduler.cfg read
01/02/2011,13:32:21,$HST:Measurement enable
01/02/2011,13:32:21,$CRX:AGC gain = 2.49V
01/02/2011,13:32:21,$CRX:Emitter BF199 = 0.14V
01/02/2011,13:32:21,$CRX:Analog Input = 9.24
01/02/2011,13:32:23,$HST:XYZ plot selected
01/02/2011,13:32:23,$HST:File frq05005.cfg read
01/02/2011,13:32:23,$HST:No calibration file found
01/02/2011,13:32:23,$HST:Plot buffer erased...
01/02/2011,13:32:23,$HST:Parametrisation RCU
01/02/2011,13:32:24,$HST:XY plot selected
01/02/2011,13:32:24,$HST:Yt plot selected
01/02/2011,13:32:25,$HST:Param. RCU due to START
01/02/2011,13:32:25,$HST:Actual focuscode 59
01/02/2011,13:32:25,$HST:Enable data transfer
01/02/2011,13:32:25,$HST:Receiver calibration
01/02/2011,13:32:25,$CRX:Started
01/02/2011,13:32:25,$HST:Start new FITS-file
01/02/2011,13:32:25,$HST:Continous measurement
01/02/2011,13:32:38,$HST:Info panel opened
01/02/2011,13:47:25,$HST:FITS #1 100rows x 7200cols
01/02/2011,14:02:25,$HST:FITS #2 100rows x 7200cols
01/02/2011,14:17:25,$HST:FITS #3 100rows x 7200cols
01/02/2011,14:32:25,$HST:FITS #4 100rows x 7200cols
01/02/2011,14:47:25,$HST:FITS #5 100rows x 7200cols
01/02/2011,15:02:25,$HST:FITS #6 100rows x 7200cols
01/02/2011,15:17:25,$HST:FITS #7 100rows x 7200cols
01/02/2011,15:32:25,$HST:FITS #8 100rows x 7200cols
01/02/2011,15:47:25,$HST:FITS #9 100rows x 7200cols
01/02/2011,16:02:25,$HST:FITS #10 100rows x 7200cols
01/02/2011,16:14:58,$HST:Measurement stop
01/02/2011,16:14:58,$HST:FITS #11 100rows x 6021cols
01/02/2011,16:14:58,$HST:Auto stop due to data loss.
01/02/2011,16:14:58,$HST:Check RS232-connection!
01/02/2011,16:14:58,$HST:Auto stop due to data loss.
01/02/2011,16:14:58,$HST:Check RS232-connection!
01/02/2011,16:14:58,$HST:EOT (&) detected
01/02/2011,16:14:58,$HST:Measurement stop
01/02/2011,16:14:58,$HST:Measurement wait...
01/02/2011,16:14:58,$HST:Measurement halted
01/02/2011,16:14:58,$HST:Measurement stop
01/02/2011,16:14:58,$CRX:Stopped
01/02/2011,16:14:58,$HST:Measurement wait...
01/02/2011,16:14:59,$HST:Measurement halted
01/02/2011,16:14:59,$HST:Measurement idle
01/02/2011,16:14:59,$CRX:Stopped
01/02/2011,16:14:59,$HST:Measurement enable
01/02/2011,16:14:59,$CRX:AGC gain = 2.49V
01/02/2011,16:14:59,$CRX:Emitter BF199 = 0.14V
01/02/2011,16:14:59,$CRX:Analog Input = 9.24
01/02/2011,16:15:01,$HST:No more entries in scheduler.
02/02/2011,00:00:00,$HST:Midnight -> memo cleared
02/02/2011,00:00:00,$HST:EOF(logfile)